Originally Posted by
pangingIII
i like to suggest you to always post your letest bios setting if you want to get done with the basic of this particular overclock quicker.
Sorry about that....
Here are my settings, I used what you suggested and I was able to boot into Windows, but BSOD in Prime 95 Blend...
Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto <===
CPU Clock Ratio .......................: 9 <===
Fine CPU Clock Ratio...................: 0.0 <===
CPU Frequency .........................: 4.05 GHz (450X9)
Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 450
PCI Express Frequency (Mhz) ...........: Auto <===
C.I.A.2 ...............................: [Disabled] <===
Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 700mV <===
PCI Express Clock Drive................: 700mV <===
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance....................: [Turbo] <===
Extreme Memory Profile (X.M.P.)........: [Auto] <===
(G)MCH Frequency Latch.................: [333MHz] <===
System Memory Multiplier ..............: 2.4B <===
Memory Frequency (Mhz) ................: 1080
DRAM Timing Selectable ................: [Manual] <===
Standard Timing Control
CAS Latency Time.......................: 5 <===
tRCD ..................................: 5 <===
tRP'...................................: 5 <===
tRAS...................................: 15 <===
Advanced Timing Control
tRRD...................................: 4 <===
tWTR...................................: 4 <===
tWR....................................: 12 <===
tRFC...................................: 68 <===
tRTP...................................: 4 <===
Command Rate (CMD) ....................: Auto <===
Driving Strength Profiles
Driving Strength ......................: Auto <===
Channel A
Static tRead Value.....................: 8 <=== or [AUTO]
tRD Phase0 Adjustment..................: [AUTO]
tRD Phase1 Adjustment..................: [AUTO]
tRD Phase2 Adjustment .................: [AUTO]
tRD Phase3 Adjustment..................: [AUTO]
Trd2rd(Different Rank).................: [AUTO]
Twr2wr(Different Rank).................: [AUTO]
Twr2rd(Different Rank).................: [AUTO]
Trd2wr(Same/Diff Rank).................: [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [Disable] <=== or [AUTO]
Channel B
Static tRead Value.....................: 8 <=== [AUTO]
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: [AUTO]
Twr2wr(Different Rank).................: [AUTO]
Twr2rd(Different Rank).................: [AUTO]
Trd2wr(Same/Diff Rank).................: [AUTO]
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [Disable] <=== or [AUTO]
Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enable]
CPU Vcore..............................: 1.250v <===> 1.325v then try lowering this value down
CPU Termination........................: 1.26V <=== then try lowering this value down to 1.24, 1.22, 1.20
CPU PLL................................: 1.50V <===
CPU Reference..........................: [AUTO] <===
MCH/ICH
MCH Core...............................: 1.26V <=== then try lowering this value down to 1.24, 1.22.
MCH Reference..........................: 0.740v <===
MCH/DRAM Ref...........................: [AUTO] <===
ICH I/O................................: 1.500V <===
ICH Core...............................: 1.100V <===
DRAM
DRAM Voltage...........................: 1.9v <===
DRAM Termination ......................: [AUTO] <===
Channel A Reference....................: [AUTO] <===
Channel B Reference ...................: [AUTO] <===
Reply With Quote
Bookmarks