The following settings give me a BSOD before entering Windows:

I am using BIOS F7c
Now, if I just change the the FSB to 400 and manualy enter my RAM timings and keep everything else on auto. I can boot into Windows and am prime stable for 3 hours...?

What do you think?

There are so many variables.

I also tried the settings listed a page or so back and could not get it to POST.


Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: FAST 			
CPU Clock Ratio .......................: 9			
Fine CPU Clock Ratio...................: 0.5			
CPU Frequency .........................: 3.80GHz (400X9.5)

Clock Chip Control 
Standard Clock Control
CPU Host Clock Control.................: [Enabled] 		
CPU Host Frequency (Mhz) ..............: 400			
PCI Express Frequency (Mhz) ...........: 100			
C.I.A.2 ...............................: [Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 800mV 
PCI Express Clock Drive................: 900mV 
CPU Clock Skew (ps)....................: 0ps 
MCH Clock Skew (ps)....................: 0ps 


DRAM Performance Control
Performance Enhance....................: [STANDARD]		
Extreme Memory Profile (X.M.P.)........: [Disabled]		
(G)MCH Frequency Latch.................: [AUTO]
System Memory Multiplier ..............: 2.66D			
Memory Frequency (Mhz) ................: 1066		
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time.......................: 5
tRCD ..................................: 5
tRP'...................................: 5
tRAS...................................: 15

Advanced Timing Control
tRRD...................................: 4
tWTR...................................: 4
tWR....................................: 5 
tRFC...................................: 62 
tRTP...................................: 4
Command Rate (CMD) ....................: 2

Driving Strength Profiles
Driving Strength ......................: 1066

Channel A
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO] 
Twr2wr(Different Rank).................: 8 [AUTO] 
Twr2rd(Different Rank).................: 7 [AUTO] 
Trd2wr(Same/Diff Rank).................: 9 [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]

Channel B
Static tRead Value.....................: 10
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: 8 [AUTO] 
Twr2wr(Different Rank).................: 8 [AUTO] 
Twr2rd(Different Rank).................: 7 [AUTO] 
Trd2wr(Same/Diff Rank).................: 9 [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [AUTO]


Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Disabled]		
CPU Vcore..............................: 1.250v 		
CPU Termination........................: 1.240V 		
CPU PLL................................: 1.570V 	
CPU Reference..........................: 0.760V [AUTO] 		


MCH/ICH
MCH Core...............................: 1.240V 		
MCH Reference..........................: 0.760v [AUTO]		
MCH/DRAM Ref...........................: 0.900V [AUTO]		
ICH I/O................................: 1.570V 		
ICH Core...............................: 1.200V 		

DRAM
DRAM Voltage...........................: 1.9v 	
DRAM Termination ......................: 0.900V [AUTO]		
Channel A Reference....................: 0.900V [AUTO]		
Channel B Reference ...................: 0.900V [AUTO]		

Advanced Settings
Limit CPUID Max. to 3..................: [Disabled]
No-Execute Memory Protect..............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support...................: [Disabled]
x C4/C4E State Support.................: [Disabled]
CPU Thermal Monitor 2(TM2) ............: [Disabled]
CPU EIST Function......................: [Disabled]
Virtualization Technology..............: [Disabled] 

Integrated Peripherals
Legacy USB Storage Detect .............:[Enabled]