Quote Originally Posted by Jsunn View Post
Sorry about that....

Here are my settings, I used what you suggested and I was able to boot into Windows, but BSOD in Prime 95 Blend...

Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto <=== 
CPU Clock Ratio .......................: 9 <=== 
Fine CPU Clock Ratio...................: 0.0 <=== 
CPU Frequency .........................: 4.05 GHz (450X9)

Clock Chip Control 
Standard Clock Control
CPU Host Clock Control.................: [Enabled] 
CPU Host Frequency (Mhz) ..............: 450 
PCI Express Frequency (Mhz) ...........: Auto <=== 
C.I.A.2 ...............................: [Disabled] <===


Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 700mV <===
PCI Express Clock Drive................: 700mV <===
CPU Clock Skew (ps)....................: 0ps 
MCH Clock Skew (ps)....................: 0ps 


DRAM Performance Control
Performance Enhance....................: [Turbo] <=== 
Extreme Memory Profile (X.M.P.)........: [Auto] <=== 
(G)MCH Frequency Latch.................: [333MHz] <===
System Memory Multiplier ..............: 2.4B <=== 
Memory Frequency (Mhz) ................: 1080 
DRAM Timing Selectable ................: [Manual] <===

Standard Timing Control
CAS Latency Time.......................: 5 <===
tRCD ..................................: 5 <===
tRP'...................................: 5 <===
tRAS...................................: 15 <===

Advanced Timing Control
tRRD...................................: 4 <===
tWTR...................................: 4 <===
tWR....................................: 12 <===
tRFC...................................: 68 <===
tRTP...................................: 4 <===
Command Rate (CMD) ....................: Auto <===

Driving Strength Profiles
Driving Strength ......................: Auto <===

Channel A
Static tRead Value.....................: 8 <=== or [AUTO]
tRD Phase0 Adjustment..................: [AUTO]
tRD Phase1 Adjustment..................: [AUTO]
tRD Phase2 Adjustment .................: [AUTO]
tRD Phase3 Adjustment..................: [AUTO]
Trd2rd(Different Rank).................: [AUTO] 
Twr2wr(Different Rank).................: [AUTO] 
Twr2rd(Different Rank).................: [AUTO] 
Trd2wr(Same/Diff Rank).................: [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [Disable] <=== or [AUTO]

Channel B
Static tRead Value.....................: 8 <=== [AUTO]
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: [AUTO] 
Twr2wr(Different Rank).................: [AUTO] 
Twr2rd(Different Rank).................: [AUTO] 
Trd2wr(Same/Diff Rank).................: [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [Disable] <=== or [AUTO]


Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enable] 
CPU Vcore..............................: 1.250v <===> 1.325v then try lowering this value down 
CPU Termination........................: 1.26V <=== then try lowering this value down to 1.24, 1.22, 1.20 
CPU PLL................................: 1.50V <=== 
CPU Reference..........................: [AUTO] <=== 


MCH/ICH
MCH Core...............................: 1.26V <=== then try lowering this value down to 1.24, 1.22. 
MCH Reference..........................: 0.740v <=== 
MCH/DRAM Ref...........................: [AUTO] <=== 
ICH I/O................................: 1.500V <=== 
ICH Core...............................: 1.100V <=== 

DRAM
DRAM Voltage...........................: 1.9v <=== 
DRAM Termination ......................: [AUTO] <=== 
Channel A Reference....................: [AUTO] <=== 
Channel B Reference ...................: [AUTO] <===
sorry i missed this post, i didn't notice it yesterday.

anyway, so this is your last message...

"I tried the settings and I was able to boot into windows. First time since trying to go to 4GHz, but it BSOD after about 5 min in Prime 95. Looks like this might be teh right path."

now i know you use the setting above, but you will want to tell me again, all the voltage value setting in your BIOS include the exact and the rest of your settings.