The cpu reference and nb reference on this board is the gtls from the dlx. The references you were using were probably to low. What you were using was essentially a .622 cpu gtl and .633 nb gtl. Try the settings below but boot it up at 430FSB then in windows use ET6 to up the FSB to 470 and test.Originally Posted by PortCitySlim
Hoss, I took your settings and tweaked them a bit for my next 470x9 run. What do you think? Anything to high or to low? Oh, yeah and BTW what ever I did to the ram settings changed my CPUZ read out, it reads 5-5-5-15 now like it should.
Well sh*t, that passes small ftt's but crashes OCCT Ram test within seconds. More then likely it is my ram settings, I really wish that damn 2.40B would boot. Maybe I'll back down to 1:1 and try 8.5x500. Could you give me what you think would be decent VTT, MCH and reference volts for 500FSB.
Code:******Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Auto ] CPU Clock Ratio.................................[ 9 ] Fine CPU Clock Ratio............................[ + 0.0 ] CPU Frequency 4.2GHz............................[ 470 x 9.0 ] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 470 ] PCI Express Frequency (Mhz).....................[ 100 ] C.I.A 2 [Disabled] ******Advanced Clock Control****** CPU Clock Drive.................................[ 1000mv ] PCI Express Clock Drive.........................[ 1000mv ] CPU Clock Skew..................................[ 0ps ] MCH Clock Skew..................................[ 0ps ] ******DRAM Performance Control****** Performance Enhance.............................[ STANDARD ] (G) MCH Frequency Latch.........................[ 333 ] System Memory Multipler.........................[ 2.40B ] Memory Frequency 1066...........................[ 1128 ] DRAM Timing Selectable..........................[ Manual ] CAS Latency Time................................[ 5 ] tRCD............................................[ 5 ] tRP.............................................[ 5 ] tRAS............................................[ 15 ] ******Advanced Timing Control****** tRRD[4]..........................................[ Auto ] tWTR[4]..........................................[ Auto ] tWR[13]..........................................[ Auto ] tRFC[68].........................................[ 54 ] tRTP[4]..........................................[ Auto ] Command Rate (cmd)[0]............................[ 2T ] ******Channel A Timing Settings****** Static tRead Value [ 9 ] ................[ 9 ] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ] tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 9 ] ................[ 9 ] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ] tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ ]..........................[ 1.3875 ] CPU Termination [ 1.20 ]...................[ 1.36 ] CPU PLL [ 1.50 ]...................[ 1.57 ] CPU Reference [ 0.760 ]...................[ 0.886 ] MCH Core [ 1.100 ]...................[ 1.36 ] MCH Reference [ 0.760 ]...................[ 0.901 ] MCH/DRAM Refernce [ 0.900 ]...................[ 1.030 ] ICH I/O [ 1.500 ]...................[ 1.500 ] ICH Core [ 1.100 ]...................[ 1.100 ] DRAM Voltage [ 1.800 ]...................[ 2.060 ] DRAM Termination [ 0.900 ]...................[ 1.030 ] Channel A Ref [ 0.900 ]...................[ 1.030 ] Channel B Ref [ 0.900 ]...................[ 1.030 ] ******Advanced BIOS Features****** Limit CPUID Max to 3............................[ Disabled ] No-Execute memory Protect.......................[ Disabled ] CPU Enhance Halt (CIE)..........................[ Disabled ] C2/C2E State Support............................[ Disabled ] C4/C4E State Support............................[ Disabled ] CPU Thermal Monitor.............................[ Disabled ] CPU EIST Function...............................[ Disabled ] Virtualization Technology.......................[ Disabled ]
Reply With Quote
Bookmarks