Hoss, I took your settings and tweaked them a bit for my next 470x9 run. What do you think? Anything to high or to low? Oh, yeah and BTW what ever I did to the ram settings changed my CPUZ read out, it reads 5-5-5-15 now like it should.
Well sh*t, that passes small ftt's but crashes OCCT Ram test within seconds. More then likely it is my ram settings, I really wish that damn 2.40B would boot. Maybe I'll back down to 1:1 and try 8.5x500. Could you give me what you think would be decent VTT, MCH and reference volts for 500FSB.Code:******Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Auto ] CPU Clock Ratio.................................[ 9 ] Fine CPU Clock Ratio............................[ + 0.0 ] CPU Frequency 4.2GHz............................[ 470 x 9.0 ] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 470 ] PCI Express Frequency (Mhz).....................[ 100 ] C.I.A 2 [Disabled] ******Advanced Clock Control****** CPU Clock Drive.................................[ 1000mv ] PCI Express Clock Drive.........................[ 1000mv ] CPU Clock Skew..................................[ 0ps ] MCH Clock Skew..................................[ 0ps ] ******DRAM Performance Control****** Performance Enhance.............................[ Turbo ] (G) MCH Frequency Latch.........................[ Auto ] System Memory Multipler.........................[ 2.00B ] Memory Frequency 1066...........................[ 1175 ] DRAM Timing Selectable..........................[ Manual ] CAS Latency Time................................[ 5 ] tRCD............................................[ 5 ] tRP.............................................[ 5 ] tRAS............................................[ 15 ] ******Advanced Timing Control****** tRRD[4]..........................................[ Auto ] tWTR[4]..........................................[ Auto ] tWR[13]...........................................[ Auto ] tRFC[68].........................................[ 54 ] tRTP[4]..........................................[ Auto ] Command Rate (cmd)[0]............................[ 2T ] ******Channel A Timing Settings****** Static tRead Value [ 9 ] ................[ 9 ] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ] tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 9 ] ................[ 9 ] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ] tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ] tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ 1200 ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ ]..........................[ 1.3875 ] CPU Termination [ 1.20 ]...................[ 1.36 ] CPU PLL [ 1.50 ]...................[ 1.57 ] CPU Reference [ 0.760 ]...................[ 0.846 ] MCH Core [ 1.100 ]...................[ 1.36 ] MCH Reference [ 0.760 ]...................[ 0.861 ] MCH/DRAM Refernce [ 0.900 ]...................[ 1.030 ] ICH I/O [ 1.500 ]...................[ 1.500 ] ICH Core [ 1.100 ]...................[ 1.100 ] DRAM Voltage [ 1.800 ]...................[ 2.060 ] DRAM Termination [ 0.900 ]...................[ 1.030 ] Channel A Ref [ 0.900 ]...................[ 1.030 ] Channel B Ref [ 0.900 ]...................[ 1.030 ] ******Advanced BIOS Features****** Limit CPUID Max to 3............................[ Disabled ] No-Execute memory Protect.......................[ Disabled ] CPU Enhance Halt (CIE)..........................[ Disabled ] C2/C2E State Support............................[ Disabled ] C4/C4E State Support............................[ Disabled ] CPU Thermal Monitor.............................[ Disabled ] CPU EIST Function...............................[ Disabled ] Virtualization Technology.......................[ Disabled ]
Reply With Quote
Bookmarks