DFI LP UT X58-T3EH8 - First bench, bios screens etc

[The Watcher]

hi guys did someone try bios 0217 yet.
i have a prob when using this bios. run cpuz 1.5 and arena then the proc multi goes down and up on it's own. and also windows report the wrong clock(it just same like when u use a notebook).
my setting are:

Genie BIOS Setting (thank to PRJ)
CPU Feature
Set VR Current Limit Max: Enabled
Thermal Management Control: Disabled
EIST Function: Enabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled
TDC = Disabled
TDP = Disabled

***** Logical Processor Setting ****
Intel HT Technology: Enabled
Active Processor Cores: All

DRAM Timing
Memory Control Setting: AUTO
Memory LowGap: 1024M

DRAM Command Rate: 1N
CAS Latency Time (tCL): 8
RAS# to CAS# Delay (tRCD): 8
RAS# Precharge (tRP): 8
Precharge Delay (tRAS): 24
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): AUTO
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1.298v
CPU VID Special Add Limit: Enabled
CPU VID Special Add: 0.070
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.63v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: 0.025
CPU VTT Voltage: 1.26v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.11v
IOH Analog Voltage: 1.10v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Strong
IOH QPI Drive Strength: Strong

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Enabled
1 core Max Turbo Ratio: 29x
2 core Max Turbo Ratio: 29x
3 core Max Turbo Ratio: 29x
4 core Max Turbo Ratio: 29x
CPU Non-Turbo Clock Ratio: 24x

BCLK/UCLK/QPI Controller Settings
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: 6400GT
CPU Base Clock (BCLK): 135 Mhz
Boot Up CPU Base Clock: 135
PCIE Clock: 102 Mhz
DRAM Frequency: BCLK x 12 1620 MHz
UnCore Frequency: BCLK x 24 3249 MHz

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Set back to bios 0206 and run normal.
thank's