@ PangingIII,

I didn't have a lot of luck with the last settings. I was able to boot into windows with all of the BIOS settings, but upone restart I would get a BIOS error and have to try something else.

I did what you suggested by changing the MCH Ref Voltages up and down. All of my settings are below. The MCH Ref was the only value I changed for each trial. The values I tested are below.

Do you think I have a chip that is just limited? Thanks again for your help, and I am also learning a great deal about the board as well.

Thanks Again,
Jason

Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto 
CPU Clock Ratio .......................: 9 
Fine CPU Clock Ratio...................: 0.0 
CPU Frequency .........................: 4.00 GHz (445X9) 

Clock Chip Control 
Standard Clock Control
CPU Host Clock Control.................: [Enabled] 
CPU Host Frequency (Mhz) ..............: 445 
PCI Express Frequency (Mhz) ...........: Auto 
C.I.A.2 ...............................: [Disabled] 

Advanced Clock Control [Press Enter]
CPU Clock Drive........................: 700mV 
PCI Express Clock Drive................: 700mV 
CPU Clock Skew (ps)....................: 0ps 
MCH Clock Skew (ps)....................: 0ps 


DRAM Performance Control
Performance Enhance....................: [Turbo]
Extreme Memory Profile (X.M.P.)........: [Auto] 
(G)MCH Frequency Latch.................: [333MHz] 
System Memory Multiplier ..............: 2.4B 
Memory Frequency (Mhz) ................: 1068 

DRAM Timing Selectable ................: [Manual] 

Standard Timing Control
CAS Latency Time.......................: 5 
tRCD ..................................: 5 
tRP'...................................: 5 
tRAS...................................: 15 

Advanced Timing Control
tRRD...................................: [AUTO] 
tWTR...................................: [AUTO] 
tWR....................................: [AUTO] 
tRFC...................................: [ 56 ]  
tRTP...................................: [AUTO] 
Command Rate (CMD) ....................: [AUTO] 

Driving Strength Profiles
Driving Strength ......................: [AUTO]

Channel A
Static tRead Value.....................: [AUTO] 
tRD Phase0 Adjustment..................: [AUTO]
tRD Phase1 Adjustment..................: [AUTO]
tRD Phase2 Adjustment .................: [AUTO]
tRD Phase3 Adjustment..................: [AUTO]
Trd2rd(Different Rank).................: [AUTO] 
Twr2wr(Different Rank).................: [AUTO] 
Twr2rd(Different Rank).................: [AUTO] 
Trd2wr(Same/Diff Rank).................: [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [Disable] 

Channel B
Static tRead Value.....................: [AUTO] 
tRD Phase0 Adjustment..................: 0 [AUTO]
tRD Phase1 Adjustment..................: 0 [AUTO]
tRD Phase2 Adjustment .................: 0 [AUTO]
tRD Phase3 Adjustment..................: 0 [AUTO]
Trd2rd(Different Rank).................: [AUTO] 
Twr2wr(Different Rank).................: [AUTO] 
Twr2rd(Different Rank).................: [AUTO] 
Trd2wr(Same/Diff Rank).................: [AUTO] 
Dimm1 Clock Skew Control...............: [AUTO]
Dimm2 Clock Skew Control...............: [AUTO]
DDR Write Training.....................: [Disable] 


Motherboard Voltage Control
CPU
Load-Line Calibration..................: [Enabled] 
CPU Vcore..............................: 1.35V 
CPU Termination........................: 1.22V 
CPU PLL................................: 1.50V 
CPU Reference..........................: [AUTO] 


MCH/ICH
MCH Core...............................: 1.20V 
MCH Reference..........................: xxxx <=== The values I entered here are as follows.
All had the same result:  0.742v, 0.752v, 0.772v, 0.732v, 0.762v
MCH/DRAM Ref...........................: [AUTO] 
ICH I/O................................: 1.500V 
ICH Core...............................: 1.100V 

DRAM
DRAM Voltage...........................: 1.80v <-> 1.90v <===
DRAM Termination ......................: [AUTO] 
Channel A Reference....................: [AUTO] 
Channel B Reference ...................: [AUTO]