Originally Posted by CryptiK
skuldarin, any suggestions on what to try with my rTL's?
Thanks to you two guys I finally passed linx. I think the biggest factor was the HT. That leads me to three questions.
1. I was able to pass prime95 with HT on at 4.6 but not linx. Once I turn HT off I can pass linx. How important is it to pass say 20 loops with linx if I can pass prime95. I mean other than benching and being able to post in the 4.5 club and stuff like that because linx is the requirement? Is it good enough, or in other words, is my system stable enough passing prime95.
2. Is a higher speed with HT off better than a lower speed with HT on or visa versa. For example, 4.6 HT off compared to 4.5 HT on.
3. Why the difference between prime95 and linx or what is the difference?
OK, I will play with that some also, or do you think I still need to since I've passed linx?
Also, do you guys have any suggestion on how I can bring my vcore down or am I pretty much stuck with where I have it for the 4.6GHz. If so would you say for 24/7 I will need to just bring the speed down so that I can keep the vcore no higher than 4.5?
Here's my settings showing the changes I've made:
Code:Target CPU Frequency 4600MHz Target DRAM Frequency 2005MHz LN2 Mode [Disabled]*** QPI Loadline Calibration [Enabled]*** Sync Mode [] AI Overclock Tuner [Manual] OC From CPU level Up [Auto] 2D Performance Booster [Disabled] CPU Ratio Setting [23.0] CPU Turbo Power Limit [Disabled] >CPU Configuration---------------------------- CPU Ratio Setting [23.0] C1E Support [Disabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetch [Enabled] MPS and ACPI MADT ordering [Modern ordering] Intel(R) Virtualization Tech [Enabled] CPU TM Function [Disabled] Execute Disable Bit [Enabled] Intel(R) HT Technology [Enabled] Disabled *Active Processor Cores [All] A20M [Disabled] *Intel(R) SpeedStep(TM) Tech [Disabled] Intel(R) C-STATE Tech [Disabled] C State package limit setting [] C1 Auto Demotion [] C3 Auto Demotion [] ---------------------------------------------- BCLK Frequency [200] PCIE Frequency [100] DRAM Frequency [DDR3-2005MHz] UCLK Frequency [3008MHz] QPI Link Data Rate [Auto] 7218 Memory Configuration Protect [Disabled] >DRAM Timing Control-------------------------- CAS# Latency [ 8 DRAM Clock] RAS# to CAS# Delay [ 8 DRAM Clock] RAS# PRE Time [ 8 DRAM Clock] RAS# ACT Time [24 DRAM Clock] RAS# to RAS# Delay [Auto] REF Cycle Time [Auto] WRITE Recovery Time [Auto] READ to PRE Time [Auto] FOUR ACT WIN Time [Auto] Back-To-BackCAS# Delay [Auto] Timing Mode [1N] Round Trip Latency on CHA [Auto] Round Trip Latency on CHB [Auto] Round Trip Latency on CHC [Auto] WRITE To READ Delay(DD) [Auto] WRITE To READ Delay(DR) [Auto] WRITE To READ Delay(SR) [Auto] READ To WRITE Delay(DD) [Auto] READ To WRITE Delay(DR) [Auto] READ To WRITE Delay(SR) [Auto] READ To READ Delay(DD) [Auto] READ To READ Delay(DR) [Auto] READ To READ Delay(SR) [Auto] WRITE To WRITE Delay(DD) [Auto] WRITE To WRITE Delay(DR) [Auto] WRITE To WRITE Delay(SR) [Auto] ---------------------------------------------- CPU Differential Amplitude [Auto] CPU Clock Skew [Auto] IOH Clock Skew [Auto] ------------ Extreme Engine Digi+ ------------ Digi+ PWR Mode [T-Balanced] PWM Volt. Control [Auto] Load-Line Calibration [Full Calibration] CPU Voltage OCP [Enabled] CPU PWM Frequency [Auto] Extreme OV [Disabled] Extreme OC [Auto] CPU Voltage [1.47500] CPU PLL Voltage [Auto] 1.4045 QPI/DRAM Core Voltage [1.30000] 1.3625 DRAM Bus Voltage [1.65625] Auto >DRAM REF Voltages---------------------------- DRAM DATA REF Voltage on CHA [Auto] DRAM CTRL REF Voltage on CHA [Auto] DRAM DATA REF Voltage on CHB [Auto] DRAM CTRL REF Voltage on CHB [Auto] DRAM DATA REF Voltage on CHC [Auto] DRAM CTRL REF Voltage on CHC [Auto] ---------------------------------------------- IOH Voltage [1.15275] IOH PCIE Voltage [Auto] ICH Voltage [1.15275] ICH PCIE Voltage [Auto] ---------- Spread Spectrum Control ----------- CPU Spread Spectrum [Auto] PCIE Spread Spectrum [Auto] ***on-board jumper dependant
Reply With Quote
Bookmarks