I just finished reading this whole thread. Took me about a week and I don't think I retained
half of the information, but thanks to all of you guys I have learned a lot.
I need some help with linx and any suggestions at all with my settings.
I can pass prime95 but linx stops with error after first loop. My average temp is below 70c.
I can drop my vcore if I go to 4500MHz but stops linx after two loops. Here's my settings:
Code:Target CPU Frequency 4600MHz Target DRAM Frequency 2005MHz LN2 Mode [Disabled]*** QPI Loadline Calibration [Enabled]*** Sync Mode [] AI Overclock Tuner [Manual] OC From CPU level Up [Auto] 2D Performance Booster [Disabled] CPU Ratio Setting [23.0] CPU Turbo Power Limit [Disabled] >CPU Configuration---------------------------- CPU Ratio Setting [23.0] C1E Support [Disabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetch [Enabled] MPS and ACPI MADT ordering [Modern ordering] Intel(R) Virtualization Tech [Enabled] CPU TM Function [Disabled] Execute Disable Bit [Enabled] Intel(R) HT Technology [Enabled] *Active Processor Cores [All] A20M [Disabled] *Intel(R) SpeedStep(TM) Tech [Disabled] Intel(R) C-STATE Tech [Disabled] C State package limit setting [] C1 Auto Demotion [] C3 Auto Demotion [] ---------------------------------------------- BCLK Frequency [200] PCIE Frequency [100] DRAM Frequency [DDR3-2005MHz] UCLK Frequency [3008MHz] QPI Link Data Rate [Auto] Memory Configuration Protect [Disabled] >DRAM Timing Control-------------------------- CAS# Latency [ 8 DRAM Clock] RAS# to CAS# Delay [ 8 DRAM Clock] RAS# PRE Time [ 8 DRAM Clock] RAS# ACT Time [24 DRAM Clock] RAS# to RAS# Delay [Auto] REF Cycle Time [Auto] WRITE Recovery Time [Auto] READ to PRE Time [Auto] FOUR ACT WIN Time [Auto] Back-To-BackCAS# Delay [Auto] Timing Mode [1N] Round Trip Latency on CHA [Auto] Round Trip Latency on CHB [Auto] Round Trip Latency on CHC [Auto] WRITE To READ Delay(DD) [Auto] WRITE To READ Delay(DR) [Auto] WRITE To READ Delay(SR) [Auto] READ To WRITE Delay(DD) [Auto] READ To WRITE Delay(DR) [Auto] READ To WRITE Delay(SR) [Auto] READ To READ Delay(DD) [Auto] READ To READ Delay(DR) [Auto] READ To READ Delay(SR) [Auto] WRITE To WRITE Delay(DD) [Auto] WRITE To WRITE Delay(DR) [Auto] WRITE To WRITE Delay(SR) [Auto] ---------------------------------------------- CPU Differential Amplitude [Auto] CPU Clock Skew [Auto] IOH Clock Skew [Auto] ------------ Extreme Engine Digi+ ------------ Digi+ PWR Mode [T-Balanced] PWM Volt. Control [Auto] Load-Line Calibration [Full Calibration] CPU Voltage OCP [Enabled] CPU PWM Frequency [Auto] Extreme OV [Disabled] Extreme OC [Auto] CPU Voltage [1.47500] CPU PLL Voltage [Auto] QPI/DRAM Core Voltage [1.30000] DRAM Bus Voltage [1.65625] >DRAM REF Voltages---------------------------- DRAM DATA REF Voltage on CHA [Auto] DRAM CTRL REF Voltage on CHA [Auto] DRAM DATA REF Voltage on CHB [Auto] DRAM CTRL REF Voltage on CHB [Auto] DRAM DATA REF Voltage on CHC [Auto] DRAM CTRL REF Voltage on CHC [Auto] ---------------------------------------------- IOH Voltage [1.15275] IOH PCIE Voltage [Auto] ICH Voltage [1.15275] ICH PCIE Voltage [Auto] ---------- Spread Spectrum Control ----------- CPU Spread Spectrum [Auto] PCIE Spread Spectrum [Auto] ***on-board jumper dependant
Reply With Quote
Bookmarks