** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[PortCitySlim]

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.5    ]
CPU Frequency 3.6GHz............................[ 425 x 8.5  ]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 425      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2 [Disabled] 
 
******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv]
PCI Express Clock Drive.........................[ 900mv]
CPU Clock Skew..................................[ 0ps]
MCH Clock Skew..................................[ 0ps]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Turbo ]
Extreme Memory Profile (XMP)....................[ Auto  ]
(G) MCH Frequency Latch.........................[ 333   ]
System Memory Multiplier........................[ 2.40B ]
Memory Frequency   ..............1066.............1020
DRAM Timing Selectable..........................[ Manual]
 
CAS Latency Time...............[ 5    ].........[ 5     ]
tRCD...........................[ 5    ].........[ 5     ]
tRP............................[ 5    ].........[ 5     ]
tRAS...........................[ 15   ].........[ 15    ]
 
******Advanced Timing Control******
 
tRRD...........................[ 4   ]..........[ Auto     ]
tWTR...........................[ 4   ]..........[ Auto     ]
tWR............................[ 6   ]..........[ Auto     ]
tRFC...........................[ 72   ].........[ 54       ]
tRTP...........................[ 4   ]..........[ Auto     ]
Command Rate (cmd).............[ 0   ]..........[ 2        ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 9        ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ Auto     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 9        ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ Auto     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled  ]
CPU Vcore         [ 1.25    ]...................[ 1.25V    ]
CPU Termination   [ 1.20    ]...................[ 1.20     ]
CPU PLL           [ 1.50    ]...................[ 1.50     ]
CPU Reference     [ 0.760   ]...................[ Auto     ]
 
MCH Core          [ 1.100   ]...................[ 1.240   ]
MCH Reference     [ 0.760   ]...................[ 0.800   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 0.96    ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]

DRAM Voltage      [1.8]...................[2.1  ] 
DRAM Termination  [0.9]...................[1.050]
Channel A Ref     [0.9]...................[1.050]
Channel B Ref     [0.9]...................[1.050]

*****************Advanced BIOS Features********* 


Limit CPUID Max to 3 ................. [disable] 
No-Execute memory Protect ............ [enable] 
CPU Enhance Halt (CIE) ............... [disable] 
C2/C2E State Support ................. [disable] 
C4/C4E State Support ................. [disable] 
CPU Thermal Monitor................... [enable] 
CPU EIST Function..................... [disable]
Virtualization Technology ............ [disable]

The first thing that catches my eye is your MCH/DRAM Reference. I would adjust this to 1.050 like your channel A/B reference. These settings I gave you last night for 2.1v RAM are exactly the same settings that Hoss331 is using for his overclock stability and they are passing 8+ hour Prime95 blends. I use a lower ram voltage but it lowers down easily enough, for every .02v you lower your RAM you will notice that the reference for that lowers .01v. I am at 2.00v RAM and a 1.000 reference.

Leaving your CPU TM and No-Execute might not cause you problems(I used to run with them enabled). But remember down the line when you try a blend/OCCT RAM large ftt packet test that disabling these can sometimes solve buggy instability problems.

Setting your performance enhance to turbo might not improve your performance overall, after tweaking you might get better settings to boot on standard. I would say that you should start with Standard and after your finished tweaking everything see if you can run on Turbo. My RAM settings are exactly as follows...

******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[  Auto/333   ] 
System Memory Multiplier........................[ 2.40B ]
Memory Frequency   ..............1066.............[ 1128 ]
DRAM Timing Selectable..........................[ Manual ]
 
CAS Latency Time...............[ 5    ].........[ 5     ]
tRCD...........................[ 5    ].........[ 5     ]
tRP............................[ 5    ].........[ 5     ]
tRAS...........................[ 15   ].........[ 15    ]
 
******Advanced Timing Control******
 
tRRD...........................[ 4   ]..........[ Auto     ]
tWTR...........................[ 4   ]..........[ Auto     ]
tWR............................[ 13   ]..........[ Auto     ]
tRFC...........................[ 68   ].........[ 54       ]
tRTP...........................[ 4   ]..........[ Auto     ]
Command Rate (cmd).............[ 2   ]..........[ 2      ]
 
******Channel A AND B Timing Settings******     
 
Static tRead Value        [ 8 ] ................[  8   ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Enabled   ]
 
******Channel A AND B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200 OC   ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]

And this is what I get when I run Everest....