** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

**coop** · 03-01-2009, 01:42 PM

@pangingIII, decent pi time. This is with out changing memory timing much w/ddr2
[IMG]

[/IMG]
and after working with clock skew I could do PL-8 at here
[IMG]

[/IMG]

**darthvedor** · 03-01-2009, 01:59 PM

Hi all,

Here is mine all settings on auto except VRAM is 2.0

**PortCitySlim** · 03-01-2009, 03:47 PM

Originally Posted by Hoss331

The cpu reference and nb reference on this board is the gtls from the dlx. The references you were using were probably to low. What you were using was essentially a .622 cpu gtl and .633 nb gtl. Try the settings below but boot it up at 430FSB then in windows use ET6 to up the FSB to 470 and test.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.2GHz............................[ 470 x 9.0 ]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 470     ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2 [Disabled] 
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv   ]
PCI Express Clock Drive.........................[ 1000mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 0ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ STANDARD ]
(G) MCH Frequency Latch.........................[ 333   ]
System Memory Multipler.........................[ 2.40B    ]
Memory Frequency 1066...........................[ 1128      ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5        ]
tRCD............................................[ 5        ]
tRP.............................................[ 5        ]
tRAS............................................[ 15       ]
 
******Advanced Timing Control******
 
tRRD[4]..........................................[ Auto    ]
tWTR[4]..........................................[ Auto    ]
tWR[13]..........................................[ Auto    ]
tRFC[68].........................................[ 54      ]
tRTP[4]..........................................[ Auto    ]
Command Rate (cmd)[0]............................[ 2T    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 9       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 9       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [  ]..........................[ 1.3875 ]
CPU Termination   [ 1.20    ]...................[ 1.36    ]
CPU PLL           [ 1.50    ]...................[ 1.57    ]
CPU Reference     [ 0.760   ]...................[ 0.886   ]
 
MCH Core          [ 1.100   ]...................[ 1.36    ]
MCH Reference     [ 0.760   ]...................[ 0.901   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 1.030   ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]
 
DRAM Voltage      [ 1.800   ]...................[ 2.060   ]
DRAM Termination  [ 0.900   ]...................[ 1.030   ]
Channel A Ref     [ 0.900   ]...................[ 1.030   ]
Channel B Ref     [ 0.900   ]...................[ 1.030   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Disabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Disabled ]

Thanks! Tongiht after work I will start testing this. I am sure I got my vcore set to about 1 or 2 notches of where I need to be. The RAM settings are going to be the hardest for me to set, on the P5Q I could run 460FSB/1150mhz/1.94v/PL8/Moderate Twister and get much better benchmark/latency results in everest then what I am getting so far with this board.

**OC Nub** · 03-01-2009, 05:54 PM

Looking a several guys palate, I noticed the advanced clock control was set to 1000/1000/0/50. I am trying to get my 9550 to 4.25ghz. Will this help and what exactly does this do? This will be my 24/7 oc. Are you guys just running these clocks for benching or are they 24/7 safe?

**l33t p1mp** · 03-01-2009, 05:56 PM

What planet do you live on? 27 hours in a day? I wish days were that long where I live...

**EliTE22** · 03-01-2009, 06:03 PM

Originally Posted by OC Nub

Looking a several guys palate, I noticed the advanced clock control was set to 1000/1000/0/50. I am trying to get my 9550 to 4.25ghz. Will this help and what exactly does this do? This will be my 24/7 oc. Are you guys just running these clocks for benching or are they 24/7 safe?

for 4.25ghz u shouldnt have use 1000/1000/0/50 maybe 800/800/0/50 but 700/700/0/0 should work fine my cpu like 700/800/0/0 at slower speed like 4.25 to 4.35ghz. do u have a EO, it should do 4.25ghz pretty easy with good 24/7 voltages

**Touche** · 03-01-2009, 06:04 PM

Originally Posted by coop

@pangingIII, decent pi time. This is with out changing memory timing much w/ddr2

and after working with clock skew I could do PL-8 at here

Templates please

**EliTE22** · 03-01-2009, 06:06 PM

Originally Posted by l33t p1mp

What planet do you live on? 27 hours in a day? I wish days were that long where I live...

are u talking about 24/7

meaning 24 hours a day, 7 days a week, is that supposed to be funny

**OC Nub** · 03-01-2009, 06:30 PM

Originally Posted by EliTE22

for 4.25ghz u shouldnt have use 1000/1000/0/50 maybe 800/800/0/50 but 700/700/0/0 should work fine my cpu like 700/800/0/0 at slower speed like 4.25 to 4.35ghz. do u have a EO, it should do 4.25ghz pretty easy with good 24/7 voltages

Thanks for responding. Yes its an EO. It is set to 800/900/0/0 atm. I guess thats default

, haven't adjusted it. just set it to 800/800/0/0 to see what happens. This is my first quad, never had to mess with most of these voltages before. On my e8400 and old mobo I ran all voltages normal/stock except the vcore. Have heard of people burning up boards due to hi voltages oc'ing a quad so kinda afraid to bump them up too hi. current volatages are.. 471x8.5 1.33125 vcore (no llc) or 1.256 LLC enabled. vtt 1.20, mch 1.28, cpu reference .785, mch reference .80, 333strap 240b 1130mhz Prime blend stable. What is considered safe for vtt, mch, cpu ref and mch ref.voltages? No water cooling just air. Thanks

**ghost_recon88** · 03-01-2009, 06:38 PM

Originally Posted by stasio

EP45-UD3P.F4Pi

Is this BIOS better for quads then normal F4? What's special about it?

**richpmd** · 03-01-2009, 06:39 PM

This week I've playing with a GIGABYTE GA-EP45-UD3P with an e8400 (E0), Freezer 7 Pro and 4 1GB Patriot DDR2 800 RAM. Unbelievably easy build. Overclocking is so easy a caveman could do it (no disrespect to you cavemen out there!) With literally one button push on Easytune 6 I had 4.05 (stock speed was 3.0). With no other changes I pushed up the FSB to achieve 4.3 in 15 minutes that is OCCT stable. Got it up to 4.635 long enough to run a 10.172 Superpi 1.5 mod.

**EliTE22** · 03-01-2009, 06:45 PM

Originally Posted by OC Nub

Thanks for responding. Yes its an EO. It is set to 800/900/0/0 atm. I guess thats default

, haven't adjusted it. just set it to 800/800/0/0 to see what happens. This is my first quad, never had to mess with most of these voltages before. On my e8400 and old mobo I ran all voltages normal/stock except the vcore. Have heard of people burning up boards due to hi voltages oc'ing a quad so kinda afraid to bump them up too hi. current volatages are.. 471x8.5 1.33125 vcore (no llc) or 1.256 LLC enabled. vtt 1.20, mch 1.28, cpu reference .785, mch reference .80, 333strap 240b 1130mhz Prime blend stable. What is considered safe for vtt, mch, cpu ref and mch ref.voltages? No water cooling just air. Thanks

for safe voltage just watch the temps, if its cool it will be fine, and with air it will get too hot before u really get into the high voltages take to stay under 1.5vcore and vtt

,
try getting the vtt closer to the vcore. maybe 1.3v and 0.871v cpu ref. voltage & mch 0.871v, should help lower the vcore a little, keep running it with out llc if u can, llc can be a headache better to leave it disable if u can

**anniku989** · 03-01-2009, 07:12 PM

Any fsb/multi or voltage change other than these settings causes it to reboot back to defaults for me...

Any idea's? I know this chip'll do 4.0 at 1.39 I believe, and I know the ram is tested good. I just have a feeling there's a setting in the bio's that's off and causing it to go fubar on me

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 19        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 3.8GHz............................[ 333 x 10.0 ]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 333    ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2 [Disabled] 
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv   ]
PCI Express Clock Drive.........................[ 1000mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 0ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ Auto   ]
System Memory Multipler.........................[ Auto   ]
Memory Frequency 1066...........................[ 1033      ]
DRAM Timing Selectable..........................[ Auto   ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [  ]..........................[ normal]
CPU Termination   [ 1.20    ]...................[ normal    ]
CPU PLL           [ 1.50    ]...................[ normal    ]
CPU Reference     [ 0.760   ]...................[ normal   ]
 
MCH Core          [ 1.100   ]...................[ normal    ]
MCH Reference     [ 0.760   ]...................[ normal   ]
MCH/DRAM Refernce [ 0.900   ]...................[ normal   ]
ICH I/O           [ 1.500   ]...................[ normal   ]
ICH Core          [ 1.100   ]...................[ normal   ]
 
DRAM Voltage      [ 1.800   ]...................[ normal   ]
DRAM Termination  [ 0.900   ]...................[ normal   ]
Channel A Ref     [ 0.900   ]...................[ normal   ]
Channel B Ref     [ 0.900   ]...................[ normal   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Disabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Disabled ]

**coop** · 03-01-2009, 07:40 PM

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto 
CPU Clock Ratio .......................: 9.0
Fine CPU Clock Ratio ..................: 0.5 
CPU Frequency .........................: 4.70GHz (495 X 9.5)

Clock Chip Control 

Standard Clock Control

CPU Host Clock Control.................: [Enabled] 
CPU Host Frequency (Mhz) ..............: 495 
PCI Express Frequency (Mhz) ...........: 100 
C.I.A.2 ...............................: [Disabled] 

Advanced Clock Control

CPU Clock Drive........................: 700
PCI Express Clock Drive................: 900
CPU Clock Skew (ps)....................: 50ps 
MCH Clock Skew (ps)....................: 100ps 

DRAM Performance Control

Performance Enhance....................: Turbo
Extreme Memory Profile (X.M.P.)........: Disabled 
(G)MCH Frequency Latch.................: 333MHz 
System Memory Multiplier ..............: 2.40D 
Memory Frequency (Mhz) ................: 1188Mhz

DRAM Timing Selectable ................: Manual 

Standard Timing Control

CAS Latency Time.......................: 5 
tRCD ..................................: 5 
tRP'...................................: 5 
tRAS...................................: 15 

Advanced Timing Control

Everything In Advanced Timing Control on auto. 
but tRFC 56 and Drive Strength Profiles 1066
DDR Write Training: Disable
Motherboard Voltage Control

CPU

Load-Line Calibration..................: [Disabled] 
CPU Vcore..............................: 1.375V
CPU Termination........................: 1.34V
CPU PLL................................: 1.63V
CPU Reference..........................: 0.888  

MCH/ICH

MCH Core...............................: 1.34V  
Reference..............................: 0.768*
MCH/DRAM Ref...........................: 0.890v
ICH I/O................................: 1.5V 
ICH Core...............................: 1.100V 

DRAM
DRAM Voltage...........................: 2.24v
DRAM Termination ......................: Auto 
Channel A Reference....................: Auto
Channel B Reference ...................: Auto

**Just learnin'** · 03-01-2009, 07:43 PM

Originally Posted by ghost_recon88

Is this BIOS better for quads then normal F4? What's special about it?

It's a benching BIOS for Duo's with E0 support removed to achieve faster SuperPi times I believe

**ghost_recon88** · 03-01-2009, 08:04 PM

Originally Posted by Just learnin'

It's a benching BIOS for Duo's with E0 support removed to achieve faster SuperPi times I believe

Thanks, I wonder if it has the same effect on E0 quads? Only one way to find out

**anniku989** · 03-01-2009, 08:11 PM

Originally Posted by coop

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto 
CPU Clock Ratio .......................: 9.0
Fine CPU Clock Ratio ..................: 0.5 
CPU Frequency .........................: 4.70GHz (495 X 9.5)

Clock Chip Control 

Standard Clock Control

CPU Host Clock Control.................: [Enabled] 
CPU Host Frequency (Mhz) ..............: 495 
PCI Express Frequency (Mhz) ...........: 100 
C.I.A.2 ...............................: [Disabled] 

Advanced Clock Control

CPU Clock Drive........................: 700
PCI Express Clock Drive................: 900
CPU Clock Skew (ps)....................: 50ps 
MCH Clock Skew (ps)....................: 100ps 

DRAM Performance Control

Performance Enhance....................: Turbo
Extreme Memory Profile (X.M.P.)........: Disabled 
(G)MCH Frequency Latch.................: 333MHz 
System Memory Multiplier ..............: 2.40D 
Memory Frequency (Mhz) ................: 1188Mhz

DRAM Timing Selectable ................: Manual 

Standard Timing Control

CAS Latency Time.......................: 5 
tRCD ..................................: 5 
tRP'...................................: 5 
tRAS...................................: 15 

Advanced Timing Control

Everything In Advanced Timing Control on auto. 
but tRFC 56 and Drive Strength Profiles 1066
DDR Write Training: Disable
Motherboard Voltage Control

CPU

Load-Line Calibration..................: [Disabled] 
CPU Vcore..............................: 1.375V
CPU Termination........................: 1.34V
CPU PLL................................: 1.63V
CPU Reference..........................: 0.888  

MCH/ICH

MCH Core...............................: 1.34V  
Reference..............................: 0.768*
MCH/DRAM Ref...........................: 0.890v
ICH I/O................................: 1.5V 
ICH Core...............................: 1.100V 

DRAM
DRAM Voltage...........................: 2.24v
DRAM Termination ......................: Auto 
Channel A Reference....................: Auto
Channel B Reference ...................: Auto

(if that is for me)
Isn't the dram voltage a bit high for stock ?

**Hoss331** · 03-01-2009, 08:16 PM

Originally Posted by anniku989

Any fsb/multi or voltage change other than these settings causes it to reboot back to defaults for me...

Any idea's? I know this chip'll do 4.0 at 1.39 I believe, and I know the ram is tested good. I just have a feeling there's a setting in the bio's that's off and causing it to go fubar on me

See if this boots.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.5    ]
CPU Frequency 3.6GHz............................[ 425 x 8.5 ]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 425     ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2 [Disabled] 
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv   ]
PCI Express Clock Drive.........................[ 1000mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 0ps     ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 266   ]
System Memory Multipler.........................[ 2.50A    ]
Memory Frequency 1066...........................[ 1062      ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5        ]
tRCD............................................[ 5        ]
tRP.............................................[ 5        ]
tRAS............................................[ 15       ]
 
******Advanced Timing Control******
 
tRRD[4]..........................................[ Auto    ]
tWTR[4]..........................................[ Auto    ]
tWR[13]..........................................[ Auto    ]
tRFC[68].........................................[ 54      ]
tRTP[4]..........................................[ Auto    ]
Command Rate (cmd)[0]............................[ 2T    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ - ] ................[ Auto     ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1066     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ - ] ................[ Auto     ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1066     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [  ]..........................[ 1.35    ]
CPU Termination   [ 1.20    ]...................[ 1.30    ]
CPU PLL           [ 1.50    ]...................[ 1.50    ]
CPU Reference     [ 0.760   ]...................[ Auto    ]
 
MCH Core          [ 1.100   ]...................[ 1.30    ]
MCH Reference     [ 0.760   ]...................[ Auto    ]
MCH/DRAM Refernce [ 0.900   ]...................[ Auto    ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]
 
DRAM Voltage      [ 1.800   ]...................[ 2.10   ]
DRAM Termination  [ 0.900   ]...................[ Auto   ]
Channel A Ref     [ 0.900   ]...................[ Auto   ]
Channel B Ref     [ 0.900   ]...................[ Auto   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Disabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Disabled ]

**ptr727** · 03-01-2009, 08:16 PM

I found this thread, but it is huge thread dealing with all sorts of issues, but I only have a problem with resuming from sleep / S3.

I have a thread going at AnandTech, where I read the great EP45-UD3P review that made me buy the board, that deals just with resume from sleep / S3 problems, if you have similar problems or solutions I'd appreciate your help:
http://forums.anandtech.com/messagev...readid=2281869

P.

**coop** · 03-01-2009, 08:26 PM

actually Touche requested it. stock??

**anniku989** · 03-01-2009, 08:38 PM

Originally Posted by Hoss331

See if this boots.

Negative on that, sir. No boot here!

**Hoss331** · 03-01-2009, 09:06 PM

hmmm, that should have booted 3.6 no problem. Have you tried that quick boost in ET6?

**anniku989** · 03-01-2009, 09:32 PM

Originally Posted by Hoss331

hmmm, that should have booted 3.6 no problem. Have you tried that quick boost in ET6?

I have a feeling there's an option I'm missing in the bio's somewhere...

I assumed the 'boost' functions in ET6 were crap (says it'll oc to 4.5 w/ vcore at like 1.6 lol), guess I'll try out the first level though

**coop** · 03-01-2009, 09:36 PM

anniku989, try those again but disable the " DDR Write Training" and raise "tRFC" to something like 58. It is easy to change after boot w/memset.

**Hoss331** · 03-01-2009, 10:03 PM

Originally Posted by anniku989

I have a feeling there's an option I'm missing in the bio's somewhere...

I assumed the 'boost' functions in ET6 were crap (says it'll oc to 4.5 w/ vcore at like 1.6 lol), guess I'll try out the first level though

Ive never used it but I figured if it did boot it would atleast give you some figures to work with. If you think theres an option your missing try loading optimized defaults to clear everything then reenter the other settings.

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

advanced clock control

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: ** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

advanced clock control

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P