** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[PortCitySlim]

need some serious help please

Try this...

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 3.4GHz............................[ 425 x 8.0  ]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 425      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2 [Disabled] 
 
******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv]
PCI Express Clock Drive.........................[ 900mv]
CPU Clock Skew..................................[ 0ps]
MCH Clock Skew..................................[ 0ps]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
Extreme Memory Profile (XMP)....................[ Auto  ]
(G) MCH Frequency Latch.........................[ Auto   ]
System Memory Multiplier........................[ 2.40B ]
Memory Frequency   ..............1066...... ...1020
DRAM Timing Selectable..........................[ Manual  ]
 
CAS Latency Time...............[ 5    ].........[ 5     ]
tRCD...........................[ 5    ].........[ 5     ]
tRP............................[ 5    ].........[ 5     ]
tRAS...........................[ 15   ].........[ 15     ]
 
******Advanced Timing Control******
 
tRRD...........................[ 4   ]..........[ Auto     ]
tWTR...........................[ 4   ]..........[ Auto     ]
tWR............................[ 6   ]..........[ Auto     ]
tRFC...........................[ 72   ].........[ 54     ]
tRTP...........................[ 4   ]..........[ Auto     ]
Command Rate (cmd).............[ 0   ]..........[ 2T     ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 9 or 10, lower is better if it boots and is stable ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1066     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 9 or 10, lower is better if it boots and is stable ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto     ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto     ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto     ]
 
Dimm 1 Clock Skew Control.......................[ Auto     ]
Dimm 2 Clock Skew Control.......................[ Auto     ]
DDR Write Training..............................[ Auto     ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1066     ]
Data Driving Pull Up Level......................[ Auto     ]
cmd Driving Pull Up Level.......................[ Auto     ]
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]
 
Data Driving Pull Down Level....................[ Auto     ]
cmd Driving Pull Down Level.....................[ Auto     ]
ctrl Driving Pull Down Level....................[ Auto     ]
clk Driving Pull Down Level.....................[ Auto     ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled  ]
CPU Vcore         [ 1.25    ]...................[ 1.28V ]
CPU Termination   [ 1.20    ]...................[ 1.30     ]
CPU PLL           [ 1.50    ]...................[ 1.50     ]
CPU Reference     [ 0.760   ]...................[ Auto     ]
 
MCH Core          [ 1.100   ]...................[ 1.26   ]
MCH Reference     [ 0.760   ]...................[ Auto   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 1.050    ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]

DRAM Voltage      [ 2.10    ]...................[ 2.100  ] 
DRAM Termination  [     ]...................[ 1.050  ]
Channel A Ref     [     ]...................[ 1.050  ]
Channel B Ref     [     ]...................[ 1.050  ]

*****************Advanced BIOS Features********* 


Limit CPUID Max to 3 ................. [disable] 
No-Execute memory Protect ............ [disable] 
CPU Enhance Halt (CIE) ............... [disable] 
C2/C2E State Support ................. [disable] 
C4/C4E State Support ................. [disable] 
CPU Thermal Monitor................... [disable] 
CPU EIST Function..................... [disable]
Virtualization Technology ............ [disable]

For 3.4ghz you might need more then 1.18 vcore, try running at a voltage nearer to your VID at first and then lower it if you can. Remember with Load Line enabled you are going to notice about a 0.03v drop from your bios setting in CPUZ, so if your target voltage is 1.25 you need 1.28 set in bios. I am not good enough at setting reference voltages but since you are only trying for a 425FSB overclock you should not be raising your Termination and MCH core levels high enough that the auto setting will hold your stability back to much and one of the better OC guys can help you set your reference volts later. You might end up needing slightly higher Termination and MCH levels, I am new to this board but I am sure this will start you in the right direction. I never use any of the Advanced BIOS crap like Virtualization/Thermal Monitor/No-Execute since this can cause stability problems, especially turn off Virtualization unless you actually use it to run Virtual OS's. Also, with your RAM being a 2x2gb 1066mhz kit I would use the 2.4B setting to get a bit closer to your standard ram speed(example is 425fsb x 2.4b = 1020mhz RAM speed). If you can, use the Ram multi's that are attached to the 333mhz and 400mhz latch but other latches can be used as well depending on what RAM speed you are aiming for. Also make sure you set your Ram voltage to specs, I am assuming the spec for your kit is 2.1v and the 1.050 reference for that voltage is good.

EDIT: I changed your overclock from 8.5x400 to 8x425 since this board can easily handle 425FSB. With 425FSB you should get much better RAM performance then with the 400FSB you were aiming for. Your perfect Vcore could be lower then what I put in the code but since I do not know your VID or if you have passed a small ftt run at 1.8vcore I changed it to 1.28(~1.25 in reality) just to get you started. If for some reason the 2.4B multi does not boot due to the bug associated with it you can try 2.5A for 1062mhz RAM.