"ASUS P5Q Deluxe discussion".

[Tulû]

Your at 413fsb x8? If you want 3.4ghz really bad then I would quit your blend and go back to 425. Use my setting but maybe start just a bit higher at first with FSB and NB volts and then work your way down if your wish.


EDIT: Tell us your complete ram settings. Make sure they are set to stock levels, 1200mhz and whatever your recommended voltage is. Disable Static Read Control at first you can always tweak that later, set to PL10 and leave your twister on auto. I guess you can use MemOC Charger if you like, it has never caused me issues. You just want your Ram to pass a blend or Ram test with OCCT right now. When you get your NB/FSB/RAM setting stable you are good to go ahead and start tweaking your ram by lowering the PL and using Static Read Control

Ok.
My rams are rated @ 1200MHz @ 5-5-5-18 trfc 33 @2.1V
Btw , 80 mins've passed with no error .

Now i'll apply these :

AI Overclock tuner: manual
CPU Ratio Setting: 8
FSB Strap to North Bridge: AUTO
FSB Frequency: 425
PCI-E Frequency: 100
DRAM Frequency: 1187
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 18
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: manual
Common Performance Level [10]
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1,37125
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1,56
FSB Termination Voltage: 1,34
DRAM Voltage: 2,10
NB Voltage: 1,34
NB GTL Reference: AUTO
SBridge Voltage: AUTO
PCIE SATA Voltage: AUTO

Load Line Calibration: enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : auto
NB Clock Skew : auto

Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: -
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: enabled
Execute Disable Bit: Disabled


Now , is there any modify needed , waiting for you .
I did not get blend stopped , yet.

Edit : Almost past 2 hours and stable.
Haven't applied above settings yet.
PortCitySlim , if you confirm these settings i will aplly.