Trying to come up with some settings that can get me a stable 4.0
These below setting get me booted into windows but not stable goes BSOD on me with Prime quick
Anyone have any suggestions or better settings that may work ?
Code:******Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Turbo ] CPU Clock Ratio.................................[ 8 ] Fine CPU Clock Ratio............................[ + 0.0 ] CPU Frequency 4.5GHz............................[ 500 x 8.0] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 500 ] PCI Express Frequency (Mhz).....................[ 100 ] C.I.A 2.........................................[ Disabled ] ******Advanced Clock Control****** CPU Clock Drive.................................[ 800mv ] PCI Express Clock Drive.........................[ 800mv ] CPU Clock Skew..................................[ 50ps ] MCH Clock Skew..................................[ 100ps ] ******DRAM Performance Control****** Performance Enhance.............................[ Turbo ] Extreme Memory Profile (X.M.P)..................[ Disabled ] (G) MCH Frequency Latch.........................[ 333 ] System Memory Multipler.........................[ 2.40B ] Memory Frequency 1066...........................[ 1200 ] DRAM Timing Selectable..........................[ Manual ] CAS Latency Time................................[ 5 ] tRCD............................................[ 5 ] tRP.............................................[ 5 ] tRAS............................................[ 15 ] ******Advanced Timing Control****** tRRD[4].........................................[ Auto ] tWTR[4].........................................[ Auto ] tWR[13].........................................[ Auto ] tRFC[68] .......................................[ Auto ] tRTP[4].........................................[ Auto ] Command Rate (cmd)[0]...........................[ Auto ] ******Channel A Timing Settings****** Static tRead Value [ 9 ] ................[ 8] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ] ................[ auto ] tWR 2wr (Differnt Rank) [ 8 ] ................[ auto ] tWR 2rd (Differnt Rank) [ 7 ] ................[ auto ] tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ oc1200] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 9 ] ................[ 8] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ oc1200] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ 1.1875 ]...................[ 1.4875v ] CPU Termination [ 1.20 ]...................[ 1.360 ] CPU PLL [ 1.50 ]...................[ 1.50 ] CPU Reference [ 0.760 ]...................[ ] < set 0.745 @ 1.20vtt MCH Core [ 1.100 ]...................[ 1.46v ] MCH Reference [ 0.760 ]...................[ ] < set 0.800 @ 1.200 vtt MCH/DRAM Refernce [ 0.900 ]...................[ normal ] ICH I/O [ 1.500 ]...................[ 1.59 ] ICH Core [ 1.100 ]...................[ 1.2 ] DRAM Voltage [ 1.800 ]...................[ 2.18 ] DRAM Termination [ 0.900 ]...................[ normal ] Channel A Ref [ 0.900 ]...................[ normal ] Channel B Ref [ 0.900 ]...................[ normal ] ******Advanced BIOS Features****** Limit CPUID Max to 3............................[ Disabled ] No-Execute memory Protect.......................[ Disabled ] CPU Enhance Halt (CIE)..........................[ Disabled ] C2/C2E State Support............................[ Disabled ] C4/C4E State Support............................[ Disabled ] CPU Thermal Monitor.............................[ Disabled ] CPU EIST Function...............................[ Disabled ] Virtualization Technology.......................[ Disabled ]
Reply With Quote
Bookmarks