Hi Donmarkoni,Originally Posted by donmarkoni
Great!Very low vCore, almost default.
No problem, just to check them out once more and I'll edit this post.
EDIT: Here it is, side by side, 220, 222, 225 and 240:
Code:Target CPU Frequency 4180MHz / 4218MHz / 4275MHz / 4080MHz Target DRAM Frequency 1763MHz / 1779MHz / 1803MHz / 1924MHz LN2 Mode: Disabled*** QPI Loadline Calibration: Enabled*** Sync Mode [Enabled] AI Overclock Tuner [Manual] OC From CPU level Up [Auto] 2D Performance Booster [Disabled] CPU Ratio Setting [19.0] CPU Turbo Power Limit [Disabled] >CPU Configuration---------------------------- CPU Ratio Setting [19.0] C1E Support [Enabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetcher [Enabled] MPS and ACPI MADT ordering [Modern] Intel(R) Virtualization Tech [Enabled] CPU TM Function [Disabled] Execute Disable Bit [Enabled] Intel(R) HT Technology [Enabled] Active Processor Cores [All] A20M [Disabled] Intel(R) SpeedStep(TM) Tech [Enabled] Performance/Watt select [Power] Intel(R) C-STATE Tech [Enabled] C State package limit setting [Auto] C1 Auto Demotion [Enabled] C3 Auto Demotion [Enabled] ---------------------------------------------- BCLK Frequency [220] / [222] / [225] / [240] PCIE Frequency [100] / [105] / [105] / [110] DRAM Frequency [1763] / [1779] / [1803] / [1924] UCLK Frequency [3528] / [3560] / [3608] / [3609] QPI Link Data Rate [7940] / [8012] / [8120] / [Slow] Memory Configuration Protect [Disabled] >DRAM Timing Control-------------------------- CAS# Latency 6 [6] RAS# to CAS# Delay 8 [8] RAS# PRE Time 6 [6] RAS# ACT Time 18 [18] RAS# to RAS# Delay 4 [4] REF Cycle Time 72 [72] WRITE Recovery Time 10 [10] READ to PRE Time 6 [6] FOUR ACT WIN Time 24 [Auto] Back-To-BackCAS# Delay 0 [Auto] Timing Mode 1N [1N] Round Trip Latency on CHA 53 [53] / [53] / [53] / [55] Round Trip Latency on CHB 54 [54] / [54] / [54] / [57] Round Trip Latency on CHC 55 [55] / [55] / [55] / [58] WRITE To READ Delay(DD) 8 [Auto] WRITE To READ Delay(DR) 8 [Auto] WRITE To READ Delay(SR) 18 [Auto] READ To WRITE Delay(DD) 7 [Auto] READ To WRITE Delay(DR) 7 [Auto] READ To WRITE Delay(SR) 7 [Auto] READ To READ Delay(DD) 7 [Auto] READ To READ Delay(DR) 6 [Auto] READ To READ Delay(SR) 4 [Auto] WRITE To WRITE Delay(DD) 7 [Auto] WRITE To WRITE Delay(DR) 7 [Auto] WRITE To WRITE Delay(SR) 4 [Auto] ---------------------------------------------- CPU Differential Amplitude [Auto] CPU Clock Skew [Auto] IOH Clock Skew [Auto] ------------ Extreme Engine Digi+ ------------ Digi+ PWR Mode [T-Balanced] PWR Volt. Control [Auto] Load-Line Calibration [Full] CPU Voltege OCP [Enabled] CPU PWM Frequency [Auto] Extreme OV [Disabled]* Extreme OC [Auto] CPU Voltage 1.336 [1.33750] / [1.33750] / [1.36250] / [1.30000] CPU PLL Voltage 1.204 [1.20575] / [1.20575] / [1.20575] / [1.20575] QPI/DRAM Core Voltage 1.296 [1.30000] / [1.30000] / [1.30000] / [1.30000] DRAM Bus Voltage 1.654 [Auto] >DRAM REF Voltages---------------------------- DRAM DATA REF Voltage on CHA [Auto] DRAM CTRL REF Voltage on CHA [Auto] DRAM DATA REF Voltage on CHB [Auto] DRAM CTRL REF Voltage on CHB [Auto] DRAM DATA REF Voltage on CHC [Auto] DRAM CTRL REF Voltage on CHC [Auto] ---------------------------------------------- IOH Voltage 1.111 [Auto] / [1.20575] / [1.25875] / [1.27200] IOH PCIE Voltage 1.508 [Auto] ICH Voltage 1.111 [Auto] ICH PCIE Voltage [Auto] *QPI Voltage OCP [Enabled] *IOH Voltage OCP [Enabled] *DRAM Voltage OCP [Enabled] *QPI PWM Frequency [Auto] *IOH PWM Frequency [Auto] *DRAM PWM Frequency [Auto] ---------- Spread Spectrum Control ----------- CPU Spread Spectrum [Disabled] DRAM Spread Spectrum [Disabled] ***on-board jumper dependant
225MHz, maybe a couple of MHz higher, but didn't tried. 230 is a no go, whatever I do. Tried max 1.4V IOH. I don't know if I should go higher just with air cooling.
BTW, check this post again in couple of minutes if you want to see BIOS settings I used.
You always leave vdram on auto ?
Reply With Quote
Bookmarks