** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[gugle]

hello, someone would have a good setup bios to run day-in day a 501x8.5 Q9550 (4.26ghz)
4 combs of memory usage, memory has been tested in Memtest is OK
watercooler CPU and NB

thanks

[bignick]

I'm having issues with getting my E6400 above 350FSB? My old ASUS P5K would do 8x400 daily with 1.4V and no increase to NB voltage. I've tried loosening timings on my ram, bumping core and mch voltage and it won't boot if I play with voltages at all. What am I doing wrong? I've been using ASUS boards all my life and because of this thread I chose a Gigabyte for my last 775 board. This bios is very different than what I'm used to looking at and I'm sure thats the problem.

[andressergio]

hello, someone would have a good setup bios to run day-in day a 501x8.5 Q9550 (4.26ghz)
4 combs of memory usage, memory has been tested in Memtest is OK
watercooler CPU and NB

thanks

hey mate lots of templates to search in this thread to test and have fun

[andressergio]

I'm having issues with getting my E6400 above 350FSB? My old ASUS P5K would do 8x400 daily with 1.4V and no increase to NB voltage. I've tried loosening timings on my ram, bumping core and mch voltage and it won't boot if I play with voltages at all. What am I doing wrong? I've been using ASUS boards all my life and because of this thread I chose a Gigabyte for my last 775 board. This bios is very different than what I'm used to looking at and I'm sure thats the problem.

can you post your settings mate ?

[Jsquire]

edit: tried some different settings and majorly ed up, 2 hours later i've had to repair my win7 install.
Okay i'm back up to 4.2Ghz with my E8500 on a EP45-UD3R 443x9.5
the only settings i've changed are as follows
cpu core - 1.4v
LLC - disabled

[andressergio]

Is there a program that can read bios settings from windows or do i have to manually copy them down?

i dunno if that exists i just take a pic and then make a template...i have them memorized now lol

[Jsquire]

******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [Auto]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0

>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [467]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]

>>>>> Advanced Clock Control..........:
CPU Clock Drive.......................: [900mV]
PCI Express Clock Drive...............: [800mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 50ps]

******** DRAM Performance Control ********

Performance Enhance...................: [Standard]
X.M.P.....[Profile 2]
MCH Frequency................: Auto
System Memory Multiplier (SPD)........: [2.40B]
Memory Frequency(Mhz).................: 1121
DRAM Timing Selectable (SPD)..........: [Auto]

>>>>> Standard Timing Control
x CAS Latency Time................5...: [ Auto]
x tRCD ...........................5...: [ Auto]
x tRP.............................5...: [ Auto]
x tRAS...........................15...: [Auto]

>>>>> Advanced Timing Control.........: [Press Enter]
(All Auto here)

****** Motherboard Voltage Control ******

>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore.....................1.2500V.........: [1.400V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.500V]
CPU Reference..........0.760V.........: [0.810]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.26]
MCH Reference..........0.760V.........: [0.810]
MCH/DRAM Reference.....0.900V.........: [Normal]
ICH I/O................1.500V.........: [Normal]
ICH Core...............1.100V.........: [Normal]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V] 
DRAM Termination.......0.900V.........: [Normal]
Channel A Reference....0.900V.........: [Normal]
Channel B Reference....0.900V.........: [Normal]

I'm trying to get this E8500 stable at 4.2Ghz, any tips?

[andressergio]

******************************
MB Intelligent Tweaker(M.I.T.)
******************************
Robust Graphics Booster ..............: [Auto]
CPU Clock Ratio ......................: [9X]
x Fine CPU Clock Ratio................: +0.0

>>>>> Standard Clock Control
CPU Host Clock Control................: [Enabled]
x CPU Host Frequency(Mhz).............: [467]
PCI Express Frequency(Mhz)............: [100]
C.I.A.2...............................: [Disabled]

>>>>> Advanced Clock Control..........:
CPU Clock Drive.......................: [900mV]
PCI Express Clock Drive...............: [800mV]
CPU Clock Skew........................: [ 0ps]
MCH Clock Skew........................: [ 50ps]

******** DRAM Performance Control ********

Performance Enhance...................: [Standard]
X.M.P.....[Profile 2]
MCH Frequency................: Auto
System Memory Multiplier (SPD)........: [2.40B]
Memory Frequency(Mhz).................: 1121
DRAM Timing Selectable (SPD)..........: [Auto]

>>>>> Standard Timing Control
x CAS Latency Time................5...: [ Auto]
x tRCD ...........................5...: [ Auto]
x tRP.............................5...: [ Auto]
x tRAS...........................15...: [Auto]

>>>>> Advanced Timing Control.........: [Press Enter]
(All Auto here)

****** Motherboard Voltage Control ******

>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore.....................1.2500V.........: [1.400V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.500V]
CPU Reference..........0.760V.........: [0.810]
>>> MCH/ICH
MCH Core...............1.100V.........: [1.26]
MCH Reference..........0.760V.........: [0.810]
MCH/DRAM Reference.....0.900V.........: [Normal]
ICH I/O................1.500V.........: [Normal]
ICH Core...............1.100V.........: [Normal]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V] 
DRAM Termination.......0.900V.........: [Normal]
Channel A Reference....0.900V.........: [Normal]
Channel B Reference....0.900V.........: [Normal]

I'm trying to get this E8500 stable at 4.2Ghz, any tips?

I never had duals but i would go for

1.3 VTT
1.32+ MCH
dont use XMP, just put disabled

900/900/0/50

[Jsquire]

After a little tinkering 4.3Ghz stable after 6 hours, thanks for your help andressergio

[radaja]

I'm trying to get this E8500 stable at 4.2Ghz, any tips?

>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore.....................1.2500V.........: [1.400V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.500V]set to 1.57v
CPU Reference..........0.760V.........: [0.810]set this to normal
>>> MCH/ICH
MCH Core...............1.100V.........: [1.26]set to 1.30v to 1.32v
MCH Reference..........0.760V.........: [0.810]set this to 0.750v
MCH/DRAM Reference.....0.900V.........: [Normal]
ICH I/O................1.500V.........: [Normal]
ICH Core...............1.100V.........: [Normal]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V]
DRAM Termination.......0.900V.........: [Normal]
Channel A Reference....0.900V.........: [Normal]
Channel B Reference....0.900V.........: [Normal]

i have an E8500 on the way and i will post my template for you.this is what worked for my E8400's i had.

[bluestang]

>>> CPU
Load-Line Calibration.................: [Enabled]
CPU Vcore.....................1.2500V.........: [1.400V]
CPU Termination........1.200V.........: [1.280V]
CPU PLL................1.500V.........: [1.500V]set to 1.57v
CPU Reference..........0.760V.........: [0.810]set this to normal
>>> MCH/ICH
MCH Core...............1.100V.........: [1.26]set to 1.30v to 1.32v
MCH Reference..........0.760V.........: [0.810]set this to 0.750v
MCH/DRAM Reference.....0.900V.........: [Normal]
ICH I/O................1.500V.........: [Normal]
ICH Core...............1.100V.........: [Normal]
>>> DRAM
DRAM Voltage...........1.800V.........: [2.10V]
DRAM Termination.......0.900V.........: [Normal]
Channel A Reference....0.900V.........: [Normal]
Channel B Reference....0.900V.........: [Normal]

i have an E8500 on the way and i will post my template for you.this is what worked for my E8400's i had.

What board you running it in?

[radaja]

ill be running it my EP45-UD3P with my cellshocks

[andressergio]

ill be running it my EP45-UD3P with my cellshocks

can't wait u join as again mate

[radaja]

thanks andressergio,hopefully i can post some OCs this weekend
right now im playing with my i3-530 and ud7.

[andressergio]

thanks andressergio,hopefully i can post some OCs this weekend
right now im playing with my i3-530 and ud7.

gogo my friend and GoGo Uruguay against Ghana in some hours

you can call me by ma name...Sergio

Cheers

[andressergio]

After a little tinkering 4.3Ghz stable after 6 hours, thanks for your help andressergio

great to hear that mate

[jjjc_93]

Just a little update from me:

Board is definitely dead, won't even turn on now. And I was looking at pictures of the board, against my board and found that a capacitor was missing just under the SATAII chip.

I have a little bit of saving to do as I just bought a Single Stage Phase unit, but soon I will have a EP45T USB3P.

Still lots of fun to be had

[radaja]

gogo my friend and GoGo Uruguay against Ghana in some hours

you can call me by ma name...Sergio

Cheers

so sergio is your first name?i kept thinking your first name was andres and sergio was your last name i learned something new today.

[andressergio]

so sergio is your first name?i kept thinking your first name was andres and sergio was your last name i learned something new today.

ya im pretty lazy on nicks...my name is Sergio Andrés

Cheers mate

[andressergio]

Just a little update from me:

Board is definitely dead, won't even turn on now. And I was looking at pictures of the board, against my board and found that a capacitor was missing just under the SATAII chip.

I have a little bit of saving to do as I just bought a Single Stage Phase unit, but soon I will have a EP45T USB3P.

Still lots of fun to be had

wow that will be awesome my friend

[radaja]

ya im pretty lazy on nicks...my name is Sergio Andrés

Cheers mate

i see you just switched it around for your username
man im not having any luck whatsoever with my UD7 and i3-530
it has a nice low vid of 1.13v but i can even get 20x200@4000 1600 cl9 to boot
dont know if its the board or the cpu,i need to get another H55M-UD2H to find out.
thank god my E8500 will be here soon,i know i will have better luck with it

[NoGuru]

No time to bench but tossed the E8500 in and booted at 4.56 on second try, should be fun when I get time.
VID is 1.1

[systemviper]

I just picked up a QX6850 that is lapped in a trade, so i will be slammin that into the GIG UD3P tomorrow, should be fun to see what it can do...

Uruguay claimed their first World Cup semi-final appearance in 40 years after a pulsating 4-2 penalty shootout win over heartbroken Ghana

[andressergio]

I just picked up a QX6850 that is lapped in a trade, so i will be slammin that into the GIG UD3P tomorrow, should be fun to see what it can do...

nice chip system enjoy it

whats that quote about us ?

[bignick]

andre I still can figure out how to "take a pic" of the bios like you guys have and posted it. I know once you get a screen shoot you can upload it to imageshack and post it . Anyway I changed my settings to mirror Jsquire and it booted fine up to 425FSB. I tried 450 and it wouldn't get past the windows load screen I'm thinking this chip needs more than 1.4Vcore? What do think?