DTV DRAGON,welcome.for you bios template to be smaller ,after you copied it and are ready to post
click the Go Advance button below,then on top you will see the # button click it and paste you template
in between the two[CODE] [CODE] things that appear.this will make you template look like this when its posted
Code:
******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ AUTO ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 4.5GHz............................[ 430x9] 3.87

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 430]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[8 00mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]

******DRAM Performance Control******

Performance Enhance.............................[ STANDARD ]

(G) MCH Frequency Latch.........................[ 333]
System Memory Multipler.........................[ 240B ]
Memory Frequency 1333...........................[ 1032 ]
DRAM Timing Selectable..........................[ AUTO ]

CAS Latency Time................................[ 9]
tRCD............................................[ 9]
tRP.............................................[ 9]
tRAS............................................[ 24]

******Advanced Timing Control******

tRRD[4].........................................[ 4]
tWTR[4].........................................[ 5]
tWR[13].........................................[ 10 ]
tRFC[68] .......................................[ 74 ]
tRTP[4].........................................[ Auto ]
Command Rate (cmd)[0]...........................[ Auto ]

******Channel A Timing Settings******

Static tRead Value [ 11 ] ................[ 11 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******

Static tRead Value [ 11] ................[ 11 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ DISABLED ]
CPU Vcore [ 1.25 ]...................[ 1.2875]
CPU Termination [ 1.20 ]...................[ AUTO ]
CPU PLL [ 1.55]...................[ AUTO]
CPU Reference [ 0.805]...................[ AUTO]

MCH Core [ 1.100 ]...................[ 1.26 ]
MCH Reference [ 0.760 ]...................[ AUTO ]
MCH/DRAM Refernce [ 0.900 ]...................[ Auto ]
ICH I/O [ 1.500 ]...................[ AUTO ]
ICH Core [ 1.100 ]...................[ AUTO]

DRAM Voltage [ 1.5]...................[ 1.64]
DRAM Termination [ 0.900 ]...................[AUTO]
Channel A Ref [ 0.900 ]...................[ DONT HAVE ]
Channel B Ref [ 0.900 ]...................[ DONT HAVE ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]__________________
now i would recommend not using auto for any of your voltages
while overclocking.as the board will set voltage very high.
like vtt and pll.
try setting these voltages for that OC ok?

Load-Line Calibration...........................[ enabled]
CPU Vcore [ 1.25 ]...................[ 1.30v]
CPU Termination [ 1.20 ]...................[ 1.22v]
CPU PLL [ 1.55]...................[ 1.57v]
CPU Reference [ 0.805]...................[ normal]

MCH Core [ 1.100 ]...................[ 1.30v ]
MCH Reference [ 0.760 ]...................[ normal ]
MCH/DRAM Refernce [ 0.900 ]...................[ normal ]
ICH I/O [ 1.500 ]...................[ normal ]
ICH Core [ 1.100 ]...................[ normal]

DRAM Voltage [ 1.5]...................[ 1.64]
DRAM Termination [ 0.900 ]...................[normal]

if this works we can start lowering voltages.keep us posted.

***********************************