ASUS Maximus II Formula - new P45 king?

[kup]

OK 1st thanks for info but its not really any good to anyone.

Need to know if its 1:1 and GTL Values etc.

I gather by your Memory Voltage its not 1:1 (which is harder on NB) unless that's PC6400 your overclocking.

I cannot go for non 1:1 for 5000FSB as my Memory will not do 1200mhz on this Mobo (supposedly it will on other Mobos as its the older Rev and clocks well).

All the Memory settings that can be enabled or disabled should not matter if 1:1 if its at least PC8500 as at 1000mhz it will be underclocked.

Also due to me currently doing some work on PC I have only 4GB installed so it again should be easier even on a Rev A2 NB.

I tried your above settings be it a different NB and CPU but it would have been a good starting point IMO.

I cannot even get to Windows, chucks it after Bios posts.

I have Primed at 500FSB before but it was not for long and no settings were stable for any 2 reboots and even tried it with only 1 Memory Module so 2GB and even a 1GB PC6400 Module I know does 1000MHZ in other Mobos and it still isn't stable.

Sorry, I was just posting the settings I had changed to achieve the clocks.

GTL settings were AUTO, ram was 400 strap, performance level 10, clock twister @ strong, dram static disabled and ram @ 1:1 so @ 1000MHz.

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 6
FSB Frequency : 500 / 510
CPU Clock Skew : Normal
North Bridge Clock Skew : Normal
FSB Strap to North Bridge : 400
DRAM Frequency: DDR2-1000 / 1020 (510MHz)
Dram Clock Skew CH1 A1 : Auto
DRAM Clock Skew CH1 A2 : Auto
Dram Clock Skew CH1 B1 : Auto
Dram Clock Skew CH1 B2 : Auto


DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : auto
Row Refresh Cycle Time : auto
Write Recovery Time : auto
Read to Precharge Time : auto

Read to Write Delay (S/D) : Auto
Write to Read Delay (S) : Auto
Write to Read Delay (D) : Auto
Read to Read Delay (S) : Auto
Read to Read Delay (D) : Auto
Write to Write Delay (S) : Auto
Write to Write Delay (D) : Auto

Write to PRE Delay : Auto
Read to PRE Delay : Auto
PRE to PRE Delay : Auto
ALL PRE to ACT Delay : Auto
ALL PRE to REF Delay : Auto

DRAM Static Read Control: Disabled
Dram Read Training : Disabled
MEM OC Charger : auto
Ai Clock Twister : strong
Transaction Booster : manual
perf level 10
pull in all disabled


PCIE Frequency : 100

CPU Voltage : 1.25
CPU PLL Voltage : 1.5
FSBT : 1.4
DRAM Voltage : 2.3
North Bridge Voltage : 1.4 / 1.5 (510MHz)
South Bridge Voltage 1.5 : 1.5
South Bridge Voltage 1.1 : 1.1

CPU GTL Reference 0 : AUTO
CPU GTL Reference 1 : AUTO
CPU GTL Reference 2 : AUTO
CPU GTL Reference 3 : AUTO
North Bridge GTL Reference : AUTO
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
North Bridge DDR Reference : AUTO

Load Line Calabration : Enabled
CPU Sread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

All 4 cores. I don't have my 520 settings to hand but these are my Prime blend 12hours stable for 500/510MHz.

I don't have any screenies atm but I can get a couple of quick LinX runs tomorrow if people want? I don't see why people would disbelieve what I've said, I thought I'd been around long enough and put enough time and effort into the Rampage Formula thread to not need to provide proof for my clocks.