finally got the w/c set up and running. got a quick and easy bump to 4400mhz, need suggestions to get 4500+

this is my setup:

ga ep45 ud3r f9
q9650 vid 1.1875
g.skill lv 9600 4x2g
corsair tx750
4870x2

cpu and nb water cooled now, and at the current settings below I run 52/53c prime and 66/67c intelburn- over 20c cooler than hsf before

here are my current settings:


******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 9 ]
Fine CPU Clock Ratio...........................[0]
CPU Frequency ...........................[ 489x9 ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 489 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 1000mv ]
PCI Express Clock Drive.........................[1000mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 50ps ]

******DRAM Performance Control******

Performance Enhance.............................[ Turbo ]
Extreme Memory Profile (X.M.P)..................[ Disabled ]
(G) MCH Frequency Latch.........................[ 333 ]
System Memory Multipler.........................[ 2.40B ]
Memory Frequency 1066...........................[ 1174 ]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[5]
tRCD............................................[5]
tRP.............................................[5]
tRAS............................................[15]

******Advanced Timing Control******

tRRD[4]......................................... auto
tWTR[4].........................................auto
tWR[8]...........................................auto
tRFC[72].........................................(54)
tRTP[4]..........................................auto
Command Rate (cmd)[0]....................auto

******Channel A Timing Settings******

Static tRead Value [ 8 ] ......................auto
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings******

Drive Strength Profile..........................[ auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******

Static tRead Value [ 8 ] .......................auto
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings******

Drive Strength Profile..........................[ auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.2500 ]..........................[ 1.35625 ]
CPU Termination [ 1.200 ]....................[ 1.28 ]
CPU PLL [ 1.500 ]...............................[ 1.50 ]
CPU Reference [ 0.760 ]......................[ 0.863 ]

MCH Core [ 1.100 ].............................[ 1.34 ]
MCH Reference [ 0.760 ]......................[ 0.810 ]
MCH/DRAM Refernce [ 0.900 ]...............[ auto ]
ICH I/O [ 1.500 ].................................[ auto ]
ICH Core [ 1.100 ]...............................[ auto ]

DRAM Voltage [ 1.800 ]........................[ 1.80 ]
DRAM Termination [ 0.900 ]...................[ .90 ]
Channel A Ref [ 0.900 ].......................[ auto ]
Channel B Ref [ 0.900 ]........................[ auto ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
CPU Thermal Monitor.............................[ Enabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Enabled ]

I have tried to get more the past few days, using several different settings and what little I know from reading forums and observing what works and doesn't work in my system. I know the cpu seems to requie less volts than many of you. I spent several weeks testing different bios settings with th hsf, and hit the wall at 4.3g. Frankly, all I know to do is guess and keep trying. Windows 7 doesnt seem to like bios crashes, and I have had to do a complete reinstall from my server several times. If anyone has advise or could point me to a thread that tell the relationship between settings and how to intelligebtly overclock it would be greatly appreciated!

Thanks