** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

**OC Nub** · 06-10-2009, 07:03 PM

I was having trouble with a UD3P, would get bsod with any OC, ran fine before. Switched out all hardware, tried different case thinking it was a wire grounduing out. Today i get a new UD3P (not an RMA, ordered a new one), put everything together and same thing, boots fine at stock only. tried 2 cpu's 3 sets of ram, different gfx card, 2 different HDD's one with a fresh install, flashed bios. Left the back off of the case to have axcess to all case wires, I tried unplugging fan wires 1 at a time, restart try different wires, and still will not oc. I am stumped. Anyone have any ideas what may be causing this?

**Hoss331** · 06-10-2009, 07:16 PM

Originally Posted by nugzo

Nice work Hoss331. Would you mind posting your bios settings using this template? Thanks a lot!! Again Great Job!!

Thanks, this is what I used for the spi 32m and prime runs. Its not final yet since im still playing with the ram.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.5GHz............................[ 500 x 9.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 500      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv  ]
PCI Express Clock Drive.........................[ 1000mv  ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 50ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 266      ]
System Memory Multipler.........................[ 2.50A    ]
Memory Frequency 1066...........................[ 1250     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[3].........................................[ 3       ]
tWTR[3].........................................[ 3       ]
tWR[6]..........................................[ 6       ]
tRFC[54]........................................[ 54      ]
tRTP[3].........................................[ 3       ]
Command Rate (cmd)[0]...........................[ 2T      ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 6 ] ................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 5 ] ................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15    ]...................[ 1.40625 ]
CPU Termination   [ 1.20    ]...................[ 1.300   ]
CPU PLL           [ 1.50    ]...................[ 1.500   ]
CPU Reference     [ 0.760   ]...................[ 0.848   ]
 
MCH Core          [ 1.100   ]...................[ 1.400   ]
MCH Reference     [ 0.760   ]...................[ 0.863   ]
MCH/DRAM Refernce [ 0.900   ]...................[ 0.970   ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.100   ]
 
DRAM Voltage      [ 1.800   ]...................[ 1.940   ]
DRAM Termination  [ 0.900   ]...................[ 0.970   ]
Channel A Ref     [ 0.900   ]...................[ 0.970   ]
Channel B Ref     [ 0.900   ]...................[ 0.970   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

more playing ram at 1275

**OC Nub** · 06-11-2009, 03:20 AM

Great price on the q9550, + free shipping. http://www.newegg.com/Product/Produc..._-Pst04Descrip

**DemonEyez** · 06-11-2009, 08:21 AM

Yes! finally I succeeded in running 4500MHz stable. I decided to give it another try, this time with an AC unit blowing in direction of my watercooling rig.
I managed to get my temps down a bit

Before I was runing LinX with 31/ 31/ 37 (stuck) / 29 idle and 81/ 79/ 76/ 76 stressed

But with the AC unit blowing I got 25 / 29 (stuck) / 37 (stuck) /22 idle and 74 / 74 / 71 / 71 stressed

I could even lower vCore a bit, down to 1.425v

So lower ambient temps are key for me running 4500MHz.

After W7 is installed this evening I'll do a Everest run for comparing bandwidth and latency with Ghostleader and Hoss

**andressergio** · 06-11-2009, 02:21 PM

Just some fun run on windows 7 7201

Cheers

Sergio

**nugzo** · 06-11-2009, 02:45 PM

Originally Posted by andressergio

Just some fun run on windows 7 7201

Cheers

Sergio

Awesome work andresergio!!! Would you mind posting your bios template as well? Thanks so much!! Here is a template you can C&P

Code:

******Gigabyte EP45 UD3P******

Robust Graphics Booster.........................[    ] 
CPU Clock Ratio.................................[     ] 
Fine CPU Clock Ratio............................[   ] 
CPU Frequency 4.25GHz...........................[   ]

******Clock Chip Control******

CPU Host Clock Control..........................[   ] 
CPU Host Frequency (Mhz)........................[       ] 
PCI Express Frequency (Mhz).....................[       ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[   ] 
PCI Express Clock Drive.........................[   ] 
CPU Clock Skew..................................[     ] 
MCH Clock Skew..................................[   ] 

******DRAM Performance Control******

Performance Enhance [Standard] 
Extreme Memory Profile (XMP)....................[   ] 
(G) MCH Frequency Latch.........................[  ]
System Memory Multipler.........................[ ] 
Memory Frequency 1066...........................[ ] 
DRAM Timing Selectable..........................[ ] 

CAS Latency Time................................[      ] 
tRCD............................................[      ] 
tRP.............................................[    ] 
tRAS............................................[   ] 

******Advanced Timing Control******

tRRD............................................[    ] 
tWTR............................................[     ] 
tWR.............................................[    ] 
tRFC............................................[     ] 
tRTP............................................[     ] 
Command Rate (cmd)..............................[      ] 

******Channel A and B Timing Settings******     

Static tRead Value        [ 0 ] ................[      ] 
tRD Phase0 Adjustment     [ 0 ] ................[  ]
tRD Phase1 Adjustment     [ 0 ] ................[   ]
tRD Phase2 Adjustment     [ 0 ] ................[   ]
tRD Phase3 Adjustment     [ 0 ] ................[  ] 

tRD 2rd (Differnt Rank)   [ 0 ] ................[   ]
tWR 2wr (Differnt Rank)   [ 0 ] ................[    ] 
tWR 2rd (Differnt Rank)   [ 0 ] ................[   ] 
tRD 2wr (Same/Difft Rank) [ 0 ] ................[ ] 

Dimm 1 Clock Skew Control.......................[   ] 
Dimm 2 Clock Skew Control.......................[    ] 
DDR Write Training..............................[ ] 

******Channel A and B Driving Settings****** 

Drive Strength Profile..........................[  ] 
Data Driving Pull Up Level......................[  ] 
cmd Driving Pull Up Level.......................[     ] 
ctrl Driving Pull Up Level......................[    ]
clk Driving Pull Up Level.......................[    ]

Data Driving Pull Down Level....................[   ] 
cmd Driving Pull Down Level.....................[  ] 
ctrl Driving Pull Down Level....................[  ] 
clk Driving Pull Down Level.....................[  ]

******Motherboard Voltage Control******

Load-Line Calibration [Enabled] 
CPU Vcore         [ 1.25000 ]...................[ ] 
CPU Termination   [ 1.20    ]...................[ ]
CPU PLL           [ 1.50    ]...................[ ]
CPU Reference     [ 0.760   ]...................[ ]

MCH Core          [1.100    ]...................[ ]  
MCH Reference     [0.760    ]...................[ ] 
MCH/DRAM Refernce [0.900    ]...................[ ] 
ICH I/O           [1.500    ]...................[ ] 
ICH Core          [1.100    ]...................[ ] 

DRAM Voltage      [1.800    ]...................[ ] 
DRAM Termination  [0.900    ]...................[ ] 
Channel A Ref     [0.900    ]...................[ ] 
Channel B Ref     [0.900    ]...................[ ]  

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ ] 
No-Execute memory Protect.......................[ ]  
CPU Enhance Halt (CIE)..........................[ ]  
C2/C2E State Support............................[  ]  
C4/C4E State Support............................[ ] 
CPU Thermal Monitor.............................[  ] 
CPU EIST Function...............................[  ] 
Virtualization Technology.......................[  ]__________________

**The Viper** · 06-11-2009, 03:00 PM

Can someone help me with this issue...I had to scale back my 4.45Ghz OC due to the heat of summer, which left me testing stability at a lower OC, which I havent tested before.
Anyways, I could pass over 10minutes of small FFts P95 before error, yet when I run Blend I can only run 23sec, 3min, 6min or below I get errors (it always varies). Now you would think, raise MCH, raise Vdimm, check RAM subtimings, play with GTLs, check Trd, etc. None of any changing of these options helped, in fact I can run only 1.16MCH, and 1.8Vdimm and pass memtest86 test 5.

So I finally and very reluctantly upped my Vcore, which solved the problem...WHATS that all about??? The first 16minutes of P95 tests RAM and MCH, yet I was failing that area, and passing over 10minutes of the most stressful CPU test (small FFTs).

Anyone see any issues or problems?

******Motherboard Intelligent Tweaker (M.I.T.)******

Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 10 ]
Fine CPU Clock Ratio............................[ + 0.0 ]
CPU Frequency 4.15GHz............................[ 415 x 10]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 415 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2.........................................[ Disabled ]

******Advanced Clock Control******

CPU Clock Drive.................................[ 900mv ]
PCI Express Clock Drive.........................[ 800mv ]
CPU Clock Skew..................................[ 50ps ]
MCH Clock Skew..................................[ 50ps ]

******DRAM Performance Control******

Performance Enhance.............................[ Turbo ]
(G) MCH Frequency Latch.........................[ 333 ]
System Memory Multipler.........................[ 2.00B ]
Memory Frequency 800............................[ 830 ]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[ 4 ]
tRCD............................................[ 4 ]
tRP.............................................[ 4 ]
tRAS............................................[ 12 ]

******Advanced Timing Control******

tRRD[3].........................................[ Auto ]
tWTR[3].........................................[ Auto ]
tWR[6]..........................................[ Auto ]
tRFC[54]........................................[ 52 ]
tRTP[3].........................................[ Auto ]
Command Rate (cmd)[0]...........................[ 2T ]

******Channel A Timing Settings******

Static tRead Value [ 8 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel A Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******

Static tRead Value [ 8 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]

tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]

Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]

******Channel B Driving Settings******

Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.216 ]...................[ 1.2375 ]
CPU Termination [ 1.20 ]...................[ 1.200 ]
CPU PLL [ 1.50 ]...................[ 1.500 ]
CPU Reference [ 0.760 ]...................[ 0.7600 ]

MCH Core [ 1.100 ]...................[ 1.28 ]
MCH Reference [ 0.760 ]...................[ 0.6800 ]
MCH/DRAM Refernce [ 0.900 ]...................[ Auto ]
ICH I/O [ 1.500 ]...................[ Auto ]
ICH Core [ 1.100 ]...................[ Auto ]

DRAM Voltage [ 1.800 ]...................[ 1.860 ]
DRAM Termination [ 0.900 ]...................[ Auto ]
Channel A Ref [ 0.900 ]...................[ Auto ]
Channel B Ref [ 0.900 ]...................[ Auto ]

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

**OC Nub** · 06-11-2009, 03:21 PM

I have had that happen also, makes it hard to figure out what v needs to be increased. I have no idea why it happens.

**andressergio** · 06-11-2009, 03:24 PM

no problem mate keep in mind that its just stable on SPI32 and CRYSIS 64 and all other games, as its a low vid 1,1875 can't ibt it...im just playing till 4700 (will be my next)

sorry this is my first time i fill a template

Code:

******Gigabyte EP45 UD3P******

Robust Graphics Booster.........................[  Turbo  ] 
CPU Clock Ratio.................................[  9x   ] 
Fine CPU Clock Ratio............................[   ] 
CPU Frequency 4.60Hz...........................[512x9]

******Clock Chip Control******

CPU Host Clock Control..........................[ enabled  ] 
CPU Host Frequency (Mhz)........................[  512  ] 
PCI Express Frequency (Mhz).....................[  102  ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 900mv  ] 
PCI Express Clock Drive.......................[ 900mv  ] 
CPU Clock Skew.................................[ 0ps    ] 
MCH Clock Skew................................[ 50ps  ] 

******DRAM Performance Control******

Performance Enhance [Turbo] 
Extreme Memory Profile (XMP)..................[profile1] 
(G) MCH Frequency Latch........................[333mhz ]
System Memory Multipler.........................[2.40B ] 
Memory Frequency 1066.........................[1229] 
DRAM Timing Selectable..........................[manual] 

CAS Latency Time..........................[ 5 ] 
tRCD............................................[ 5 ] 
tRP..............................................[ 5 ] 
tRAS............................................[ 15 ] 

******Advanced Timing Control******

tRRD............................................[ 3  ] 
tWTR...........................................[ 3  ] 
tWR.............................................[ 4  ] 
tRFC............................................[ 50 ] 
tRTP............................................[ 3  ] 
Command Rate (cmd)..............................[ auto ] 

******Channel A and B Timing Settings******     

Static tRead Value           [ 0 ] ................[ 8 ] 
tRD Phase0 Adjustment     [ 0 ] ................[ auto ]
tRD Phase1 Adjustment     [ 0 ] ................[ auto ]
tRD Phase2 Adjustment     [ 0 ] ................[ auto ]
tRD Phase3 Adjustment     [ 0 ] ................[ auto ] 

tRD 2rd (Differnt Rank)    [ 0 ] ..................[ 9 ]
tWR 2wr (Differnt Rank)   [ 0 ] .................[ 7 ] 
tWR 2rd (Differnt Rank)    [ 0 ] .................[ 8 ] 
tRD 2wr (Same/Difft Rank) [ 0 ] ................[ 8 ] 

Dimm 1 Clock Skew Control.......................[auto] 
Dimm 2 Clock Skew Control.......................[auto] 
DDR Write Training..................................[auto ] 

******Channel A and B Driving Settings****** 

Drive Strength Profile.........................[auto] 
Data Driving Pull Up Level....................[auto] 
cmd Driving Pull Up Level.....................[auto] 
ctrl Driving Pull Up Level......................[auto]
clk Driving Pull Up Level.......................[auto]

Data Driving Pull Down Level..................[auto] 
cmd Driving Pull Down Level...................[auto] 
ctrl Driving Pull Down Level....................[auto] 
clk Driving Pull Down Level.....................[auto]

******Motherboard Voltage Control******

Load-Line Calibration [Enabled] 
CPU Vcore         [ 1.18750 ]...................[1,43750v ] 
CPU Termination   [ 1.20    ]...................[1,38 ]
CPU PLL           [ 1.50    ]...................   [1,57 ]
CPU Reference     [ 0.760   ]..................[0,899 ]

MCH Core          [1.100    ]...................[1,46 ]  
MCH Reference     [0.760    ].................[0,914] 
MCH/DRAM Refernce [0.900    ]..............[auto] 
ICH I/O           [1.500    ]...................[1,500 ] 
ICH Core          [1.100    ]..................[1,200 ] 

DRAM Voltage      [1.800    ]..................[2,22 ] 
DRAM Termination  [0.900    ].................[auto ] 
Channel A Ref     [0.900    ]...................[auto ] 
Channel B Ref     [0.900    ]...................[auto ]  

******Advanced BIOS Features******

ALL DISABLED...

Limit CPUID Max to 3............................[ ] 
No-Execute memory Protect..................[ ]  
CPU Enhance Halt (CIE)........................[ ]  
C2/C2E State Support..........................[ ]  
C4/C4E State Support..........................[ ] 
CPU Thermal Monitor............................[ ] 
CPU EIST Function..............................[ ] 
Virtualization Technology......................[ ]

cheers

Sergio

**OC Nub** · 06-11-2009, 03:34 PM

Thats an awesome CPU andressergio, great job with 512fsb.

**maxine** · 06-11-2009, 03:46 PM

QX9650 at 515x8.5 waku by Dtek-Fuzion & TripleRad
Gigabyte EP45-UD3P (air + 90cfm fan)
Gigabyte HD4670
2 x 1024mb Crucial BallistiX Tracer pc2-8500
Corsair HX1000

**andressergio** · 06-11-2009, 03:50 PM

Originally Posted by OC Nub

Thats an awesome CPU andressergio, great job with 512fsb.

thank you mate

Cheers
Sergio

**andressergio** · 06-11-2009, 03:52 PM

Originally Posted by maxine

QX9650 at 515x8.5 3D stable (BIOS config in notepad)
Gigabyte EP45-UD3P
Gigabyte HD4670
2 x 1024mb Crucial BallistiX Tracer pc2-8500
Corsair HX1000

great maxine !

Cheers

Sergio

**Jor3lBR** · 06-11-2009, 04:14 PM

Originally Posted by LuKe88

what NB Waterblock do you suggest for my ud3r ?
and for the mosfets are 2 enzotech mst 81 good ?

I have this complete MIPS Freezer Kit (POM) that I organized the group purchase here:

http://www.xtremesystems.org/forums/...d.php?t=210836

It's still in box never used, I will post on sale here in XS and eBay.

Interested please PM me.

**nugzo** · 06-11-2009, 04:15 PM

Originally Posted by andressergio

no problem mate keep in mind that its just stable on SPI32 and CRYSIS 64 and all other games, as its a low vid 1,1875 can't ibt it...im just playing till 4700 (will be my next)

sorry this is my first time i fill a template

Code:

******Gigabyte EP45 UD3P******

Robust Graphics Booster.........................[  Turbo  ] 
CPU Clock Ratio.................................[  9x   ] 
Fine CPU Clock Ratio............................[   ] 
CPU Frequency 4.60Hz...........................[512x9]

******Clock Chip Control******

CPU Host Clock Control..........................[ enabled  ] 
CPU Host Frequency (Mhz)........................[  512  ] 
PCI Express Frequency (Mhz).....................[  102  ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 900mv  ] 
PCI Express Clock Drive.......................[ 900mv  ] 
CPU Clock Skew.................................[ 0ps    ] 
MCH Clock Skew................................[ 50ps  ] 

******DRAM Performance Control******

Performance Enhance [Turbo] 
Extreme Memory Profile (XMP)..................[profile1] 
(G) MCH Frequency Latch........................[333mhz ]
System Memory Multipler.........................[2.40B ] 
Memory Frequency 1066.........................[1229] 
DRAM Timing Selectable..........................[manual] 

CAS Latency Time..........................[ 5 ] 
tRCD............................................[ 5 ] 
tRP..............................................[ 5 ] 
tRAS............................................[ 15 ] 

******Advanced Timing Control******

tRRD............................................[ 3  ] 
tWTR...........................................[ 3  ] 
tWR.............................................[ 4  ] 
tRFC............................................[ 50 ] 
tRTP............................................[ 3  ] 
Command Rate (cmd)..............................[ auto ] 

******Channel A and B Timing Settings******     

Static tRead Value           [ 0 ] ................[ 8 ] 
tRD Phase0 Adjustment     [ 0 ] ................[ auto ]
tRD Phase1 Adjustment     [ 0 ] ................[ auto ]
tRD Phase2 Adjustment     [ 0 ] ................[ auto ]
tRD Phase3 Adjustment     [ 0 ] ................[ auto ] 

tRD 2rd (Differnt Rank)    [ 0 ] ..................[ 9 ]
tWR 2wr (Differnt Rank)   [ 0 ] .................[ 7 ] 
tWR 2rd (Differnt Rank)    [ 0 ] .................[ 8 ] 
tRD 2wr (Same/Difft Rank) [ 0 ] ................[ 8 ] 

Dimm 1 Clock Skew Control.......................[auto] 
Dimm 2 Clock Skew Control.......................[auto] 
DDR Write Training..................................[auto ] 

******Channel A and B Driving Settings****** 

Drive Strength Profile.........................[auto] 
Data Driving Pull Up Level....................[auto] 
cmd Driving Pull Up Level.....................[auto] 
ctrl Driving Pull Up Level......................[auto]
clk Driving Pull Up Level.......................[auto]

Data Driving Pull Down Level..................[auto] 
cmd Driving Pull Down Level...................[auto] 
ctrl Driving Pull Down Level....................[auto] 
clk Driving Pull Down Level.....................[auto]

******Motherboard Voltage Control******

Load-Line Calibration [Enabled] 
CPU Vcore         [ 1.18750 ]...................[1,43750v ] 
CPU Termination   [ 1.20    ]...................[1,38 ]
CPU PLL           [ 1.50    ]...................   [1,57 ]
CPU Reference     [ 0.760   ]..................[0,899 ]

MCH Core          [1.100    ]...................[1,46 ]  
MCH Reference     [0.760    ].................[0,914] 
MCH/DRAM Refernce [0.900    ]..............[auto] 
ICH I/O           [1.500    ]...................[1,500 ] 
ICH Core          [1.100    ]..................[1,200 ] 

DRAM Voltage      [1.800    ]..................[2,22 ] 
DRAM Termination  [0.900    ].................[auto ] 
Channel A Ref     [0.900    ]...................[auto ] 
Channel B Ref     [0.900    ]...................[auto ]  

******Advanced BIOS Features******

ALL DISABLED...

Limit CPUID Max to 3............................[ ] 
No-Execute memory Protect..................[ ]  
CPU Enhance Halt (CIE)........................[ ]  
C2/C2E State Support..........................[ ]  
C4/C4E State Support..........................[ ] 
CPU Thermal Monitor............................[ ] 
CPU EIST Function..............................[ ] 
Virtualization Technology......................[ ]

cheers

Sergio

Thanks a lot! I've been running my 9650 at 4500mhz for as long as this board has been out. I never have any blue screens, locks, restarts, absolutley no stability issues at all. Yet i cant complete P95 or Intel Burn test for any length of time. At this point, it doesnt really matter a whole lot because it does what i want it to do. I just want to try other peoples settings to see what happens. If i'm not mistaken, your 24/7 Clock is 4500mhz right? Do you mind posting your settings for that as well? or maybe just let me know what is different from your above post. Thanks again and i will try your settings now.

**the_real_7** · 06-11-2009, 04:57 PM

Hey guys need a bit of help weird problem not sure when maybe after vista 64 sp2 update my lan started acting up , it disconnects when im in utorrent .. tested router other pcs on network, seems to be isolated to my pc so next I put in a old linksys nic 100 card , I mean this thing this is from like 2000 lmao and its running better than my onboard lans , cant properly check on my dual boot windows 7 cause the utorrent wont work at all cuase of compatibility problems ... so could it be mine lan going bad could it be a setting or is it a sp2 problem , redid newest drivers also and tried both lans , work fine under regular usage in firefox with internet download manager

Update : so far my old lan card is doing much better ill get some screen pics up
I think for sure its a compatibility problem with the new realtek lan drivers and Vista 64 sp2 and not a hardware problem , maybe look into getting a good lan card for like 20 bucks

**DemonEyez** · 06-12-2009, 12:51 AM

Originally Posted by nugzo

Thanks a lot! I've been running my 9650 at 4500mhz for as long as this board has been out. I never have any blue screens, locks, restarts, absolutley no stability issues at all. Yet i cant complete P95 or Intel Burn test for any length of time. At this point, it doesnt really matter a whole lot because it does what i want it to do. I just want to try other peoples settings to see what happens. If i'm not mistaken, your 24/7 Clock is 4500mhz right? Do you mind posting your settings for that as well? or maybe just let me know what is different from your above post. Thanks again and i will try your settings now.

I experienced the exact same thing, also with 4500MHz. ( See my earlier posts) . Only after getting my temps down af few degrees, I could run IBT and P95 error free.

**jonathankru** · 06-12-2009, 03:38 AM

I finally got My Cpu Stable enough at 4.6Ghz(with 8 Gigs of ram) to run Vnatgae and 3d Mark06 in Win 7 7201

Physics disabled in Vantage

Thanks to everyone who helped me get this

I still have to see if i can bring vcore down. But my cpu likes lots of volts compared to what everyone one else is using. But my temps are still good

**OC Nub** · 06-12-2009, 04:13 AM

Originally Posted by jonathankru

I finally got My Cpu Stable enough at 4.6Ghz(with 8 Gigs of ram) to run Vnatgae and 3d Mark06 in Win 7 7201

Physics disabled in Vantage

Thanks to everyone who helped me get this

I still have to see if i can bring vcore down. But my cpu likes lots of volts compared to what everyone one else is using. But my temps are still good

Excellent job.

**Alpha&OmegaX** · 06-12-2009, 04:25 AM

wow the ep45-ud3p clocks real well, and to think I just sold mine for another board because I thought it would be better for quad..

**Ghostleader** · 06-12-2009, 08:52 AM

Originally Posted by jonathankru

I finally got My Cpu Stable enough at 4.6Ghz(with 8 Gigs of ram) to run Vnatgae and 3d Mark06 in Win 7 7201

Physics disabled in Vantage

Thanks to everyone who helped me get this

I still have to see if i can bring vcore down. But my cpu likes lots of volts compared to what everyone one else is using. But my temps are still good

Nice to see

Here´s mine EPT45 Q9650 @ 512 ~4,6GHz with 2x2 ram @ 1638 777 21 tRD 9.

3DMark06 are pretty close, you got better VGA points due to higher core clock but I got higher CPU score probably due to better bandwidth and latency from my ram.

Do you run ram @ 1000 CAS5 and with which tRD?
Screenie of bandwidth and latency maybe?

We see the similary tendency with 3DMark Vantage as with the 3DMark06.

It seems like I lose points when I run 3DMark06 with Win 7 64bit compare to XP 32bit with ~1500 points.

**andressergio** · 06-12-2009, 10:22 AM

here's mine

Cheers

Sergio

**Leeghoofd** · 06-12-2009, 10:35 AM

You show off :p

**Hoss331** · 06-12-2009, 10:36 AM

Sergio, it you dont mind rerun that setup under win7, curious to see the difference from xp to 7201.

**jonathankru** · 06-12-2009, 10:45 AM

Originally Posted by andressergio

here's mine

Cheers

Sergio

That is not fair

I can boot @ 4.75Ghz but it is only 1M Super PI stable.
I have to put 1.55V to the CPU though. Not sure if it is good for the CPU.My temps all stay below 68 though.

Originally Posted by Ghostleader

Nice to see

Here´s mine EPT45 Q9650 @ 512 ~4,6GHz with 2x2 ram @ 1638 777 21 tRD 9.

3DMark06 are pretty close, you got better VGA points due to higher core clock but I got higher CPU score probably due to better bandwidth and latency from my ram.

Do you run ram @ 1000 CAS5 and with which tRD?
Screenie of bandwidth and latency maybe?

We see the similary tendency with 3DMark Vantage as with the 3DMark06.

It seems like I lose points when I run 3DMark06 with Win 7 64bit compare to XP 32bit with ~1500 points.

I am running 8 Gigs of ram at 1:1 with 5-5-5-15 pl 9.
I know my ram is holding my oc back. My Bandwidth are between 9200 - 9300 with latency of 58 or so.
When i try go higher i will SS a everst benchmark.
So my slightly higher card gets balanced by your higher memory bandwidth. COOL

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

some fun

515 fsb

FS: UD3P Mips WB Kit (POM) for UD3P/UD3R etc

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: ** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

some fun

515 fsb

FS: UD3P Mips WB Kit (POM) for UD3P/UD3R etc

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P