Well, I have just recieved my UD3P, the board looks nice, but like always Gigabyte thought that most of users are color-blind.
In comparison to my previous motherboard (ga-x48-ds4) this one have almost twice the options I had before. And that is good from a side and bad (just for now) from other side, because I dont know what does some of those options. And good because I can touch a little bit more.

I attach my Bios options, where I just move slightly some numbers.
And also I bring up (in red fonts) the options wich I dont know what they do, so if someone dont bother, could give me a little explanation.

Thanks in advance.


Template for Gigabyte Users
Code:
******Gigabyte EP45 UD3P******

Q9650 389 X 9 3510MHz 

Robust Graphics Booster.........................[ Auto     ] 
CPU Clock Ratio.................................[ 9        ] 
Fine CPU Clock Ratio............................[ 0        ] 
CPU Frequency 4.35GHz...........................[ 389 x 9  ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled  ] 
CPU Host Frequency (Mhz)........................[ 389      ] 
PCI Express Frequency (Mhz).....................[ 100      ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv   ] 
PCI Express Clock Drive.........................[ 900mv   ] 
CPU Clock Skew..................................[ 0ps      ] 
MCH Clock Skew..................................[ 0ps     ] 

******DRAM Performance Control******

Performance Enhance [Standard] 
Extreme Memory Profile (XMP)....................[ Auto ] 
(G) MCH Frequency Latch.........................[ 333MHz ] ---> If I have an FSB higher than 400 I should use the 400MHz option here??
System Memory Multipler.........................[ 2.40B  ] 
Memory Frequency 1066...........................[ 936 ] 
DRAM Timing Selectable..........................[ Manual ] 

CAS Latency Time................................[ 5        ] 
tRCD............................................[ 5        ] 
tRP.............................................[ 5        ] 
tRAS............................................[ 15       ] 

******Advanced Timing Control******

tRRD............................................[ Auto     ] 
tWTR............................................[ Auto     ] 
tWR.............................................[ Auto     ] 
tRFC............................................[ Auto     ] 
tRTP............................................[ Auto     ] 
Command Rate (cmd)..............................[ Auto     ] 

******Channel A Timing Settings******     

Static tRead Value        [ 7 ] ................[ 8        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ Auto ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Channel B Timing Settings******     

Static tRead Value        [ 7 ] ................[ 8        ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ Auto  ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Motherboard Voltage Control******

Load-Line Calibration [Enabled] 
CPU Vcore         [ 1.25000 ]...................[ 1.27500  ] 
CPU Termination   [ 1.20    ]...................[ 1.260   ] ---> This is VTT? (Which one shouldn be over 1.35/1.40?? And also it refers to Vdrop??
CPU PLL           [ 1.50    ]...................[ 1.500  ]
CPU Reference     [ 0.766   ]...................[ 0.768   ]

MCH Core          [1.1      ]...................[ 1.200  ]  
MCH Reference     [0.760    ]...................[ 0.778   ] 
MCH/DRAM Refernce [0.900    ]...................[ 0.910 ] 
ICH I/O           [1.500    ]...................[ 1.500  ] 
ICH Core          [1.100    ]...................[ 1.100  ] 

DRAM Voltage      [1.800    ]...................[ 2.000    ] 
DRAM Termination  [0.900    ]...................[ 1.000   ] 
Channel A Ref     [0.900    ]...................[ 1.000  ] 
Channel B Ref     [0.900    ]...................[ 1.000  ]  

******Advanced BIOS Features******

CPU Multithreading..............................[ Disabled ] ---> I dont know where is this one. 
Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Disabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Enabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Disabled ]