** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[rubber5]

ok i have notest thay my q9450 @2.66ghz gives me no better results even at 3.5ghz im getting 17245 in 3d mark 06 instead of 13314 but in fallout 3 im getting 50fps no matter what i do with overclocking v-sink is disabled so i dont know why its happining
Has anyone got any ideas why this is happining or is it just me been a idiot and not doing something

thanks guys
im so gelous on the overclocks your getting wish i had the balls to push my rig that far

sorry for spelling

[Loco23]

I had 9450@3.92 on water, vCore 1.525. UD3P can more than 3.5GHz.

[rubber5]

I had 9450@3.92 on water, vCore 1.525. UD3P can more than 3.5GHz.

mine is on air but did you notace a difference in fps in games

[Jupiler]

Yep

Thanks.
Nice Q9650 you have there. What batch#?

[Loco23]

This my stable settings:

MB Intelligent Tweaker(M.I.T.) 

Robust Graphics Booster .................: Auto 
CPU Clock Ratio .........................: 8x 
Fine CPU Clock Ratio.....................: +0.0 
CPU Frequency ...........................: 3.92GHz (490x8) 


********** Clock Chip Control ************ 

>>>>> Standard Clock Control 
CPU Host Clock Control...................: Enabled 
CPU Host Frequency (Mhz) ................: 490Mhz 
PCI Express Frequency (Mhz) .............: 100 

C.I.A.2 .................................: Disabled 

>>>>> Advanced Clock Control [Press Enter] 
CPU Clock Drive..........................: 800mV 
PCI Express Clock Drive..................: 900mV 
CPU Clock Skew (ps)......................: 0ps 
MCH Clock Skew (ps)......................: 0ps 


********** DRAM Performance Control ****** 

Performance Enhance......................: Turbo] 
Extreme Memory Profile (X.M.P.)..........: Disabled 
(G)MCH Frequency Latch...................: 333 
System Memory Multiplier ................: 2.40B 
Memory Frequency (Mhz) ..................: 1176 
DRAM Timing Selectable ..................: Manual 

Standard Timing Control 
CAS Latency Time.........................: 5 
tRCD ....................................: 5 
tRP'.....................................: 5 
tRAS.....................................: 15 

>>>>> Advanced Timing Control [Press Enter] 
>>>>> Channel A Timing Settings [Press Enter] 
Static tRead Value.......................: 8 
>>>>> Channel B Timing Settings [Press Enter] 
Static tRead Value.......................: 8 

********** Motherboard Voltage Control *** 
>>>>> CPU 
CPU Vcore................................: 1.525 change this for your CPU
CPU Termination..........................: 1.36 
CPU PLL..................................: 1.57 
CPU Reference............................: 0.901 

>>>>> MCH/ICH 
MCH Core.................................: 1.36 
MCH Reference............................: 0.863 
MCH/DRAM Reference.......................: Auto 
ICH I/O..................................: 1.5 
ICH Core.................................: 1.1 

>>>>> DRAM 
DRAM Voltage.............................: 2.18 change this for your RAM
DRAM Termination.........................: Auto 
Channel A Reference......................: Auto 
Channel B Reference......................: Auto 


Advanced Settings 

Limit CPUID Max. to 3....................: Disabled 
No-Execute Memory Protect................: Enabled 
CPU Enhanced Halt (C1E)..................: Disabled 
C2/C2E State Support.....................: Disabled 
C4/C4E State Support.....................: Disabled 
CPU Thermal Monitor 2(TM2) ..............: Enabled 
CPU EIST Function........................: Disabled 
Virtualization Technology................: Disabled

[Loco23]

mine is on air but did you notace a difference in fps in games

I don't know, did't do any tests.

[bluestang]

Alright overclocking experts...I'm trying to get my system at 8.5x500 FSB with 2.40B RAM multi for 1200 MHZ. After I adjust settings in BIOS (or ET6 after boot), what are the first tests I should run? Prime small, large or blend? Or 32m Pi run? Or memtest from USB key? Also, what failures mean what in specific tests when it happens quickly or after testing a while? I think this info would help everyone out instead of just trying to jump into a Prime blend for 8+ hours. Thanks!!!

[Hoss331]

Thanks.
Nice Q9650 you have there. What batch#?

batch is L827A945, 1.15VID

[kagula323]

@ Ghostleader ... how is the Rampage Formula with Dual Cores in overclocking?

[kagula323]

What about E8500 FPO:Q828A339? does anyone have it? it's E0? please post u'r results ... if u have the same fpo or fpo q828 on your E8500

[pangingIII]

8GB (4x2GB) RAM - EP45T-UD3R - Q9550

[bluestang]

Anyone have UD3R on F9 BIOS running 500fsb x 8 or 8.5 with 2.4B mem latch for 2x1GB sticks? I can't get it to post....it tries twice, each with multiples beeps, then resets to default. I was running this setup (500x8 or 525x8) fine before with 2.0B or 2.0D for 1:1 ram with 2x2GB Dominators. But I since bought a Kingston HyperX DDR2-1150 2x1GB kit and want to run 2.4B for 1200mhz. Or am I better off running 450fsb with 2.66D? Any ideas or suggestions?

[stasio]

New BIOS:
GA-EP45-UD3P - F9l
Released 08.05.09

[Don_Dan]

New BIOS:
GA-EP45-UD3P - F9l
Released 08.05.09

Thanks!

Any changes known? Changelog?

[HeXploiT]

I just had the most amazingly simple overclock with the ep45ud3p and an e8500. I finished setting up a friends rig and only had a little time left so I bumped the voltage on his 8500 to 3.7 and bumped the fsb to a nice round number and BANG! a stable 4.08ghz right off the bat.
What a sweet motherboard.

EDIT Sorry I meant 1.37.

[unclewebb]

I finished setting up a friends rig and only had a little time left so I bumped the voltage on his 8500 to 3.7 and bumped the fsb to a nice round number and BANG! a stable 4.08ghz right off the bat.

If you set your friends' core voltage to 3.7 volts then it's surprising his CPU didn't go BANG!!!

[spinejam]

If you set your friends' core voltage to 3.7 volts then it's surprising his CPU didn't go BANG!!!

[rubber5]

sorry to ask again but no one has sed if there getting more frames when thay overclock

like i sed i have a q9450@2.6 and no change in games even when i go to 3.5ghz
i have a gtx280 (no oc) but nothing gives me more frames is it just the 280 cant handle anymore frames or is is something im doing wrong
PLEASE HELP ME
thanks
ps SWEET overclocks im seeing i wish i had the mony to get better frames in my games (sli)

[Angmaar]

sorry to ask again but no one has sed if there getting more frames when thay overclock

like i sed i have a q9450@2.6 and no change in games even when i go to 3.5ghz
i have a gtx280 (no oc) but nothing gives me more frames is it just the 280 cant handle anymore frames or is is something im doing wrong
PLEASE HELP ME
thanks
ps SWEET overclocks im seeing i wish i had the mony to get better frames in my games (sli)

The best thing to do would be overclock your GTX 280. Use EVGA Precision to do the overclocking and use Furmark to test stability.

[rubber5]

The best thing to do would be overclock your GTX 280. Use EVGA Precision to do the overclocking and use Furmark to test stability.

the only thing is that it can get to mid 90c as it is i dont want to burn it out
ps i dont know what the card can go to with the temp
thanks

[simone18]

[rubber5]

with thease sort of overclocks what temp is the northbrige getting are you all watercooling it.
Mine is hitting near 60c but i dont think everest is picking it up right sine its not hot to touch

[Hoss331]

As far as I know there is no nb temp sensor on these boards, just one close to the sb.

[radaja]

with thease sort of overclocks what temp is the northbrige getting are you all watercooling it.
Mine is hitting near 60c but i dont think everest is picking it up right sine its not hot to touch

As far as I know there is no nb temp sensor on these boards, just one close to the sb.

Hoss331 is exactly right.
Rubber try touching the south bridge heatsink whe everest shows 60c.i bet it will be very warm
my new UD3R rev 1.1 SB H/S is very hot compared to my UD3P

[HeXploiT]

If you set your friends' core voltage to 3.7 volts then it's surprising his CPU didn't go BANG!!!

Oops I left out a digit. How about 1.37.