still waiting andres or jor3lbr for one of you to post those bios settings.in the meantime,heres where im at with my new g.skil9600's and new board.primeblend 2hrs50+min
Code:*****Motherboard Intelligent Tweaker (M.I.T.)****** Robust Graphics Booster.........................[ Auto ] CPU Clock Ratio.................................[ 8 ] Fine CPU Clock Ratio............................[ + 0.5 ] CPU Frequency 3.6GHz............................[ 510 x 8.5 ] ******Clock Chip Control****** CPU Host Clock Control..........................[ Enabled ] CPU Host Frequency (Mhz)........................[ 510 ] PCI Express Frequency (Mhz).....................[ 100 ] C.I.A 2 [Disabled] ******Advanced Clock Control****** CPU Clock Drive.................................[ 1000mv] PCI Express Clock Drive.........................[ 900mv] CPU Clock Skew..................................[ 0ps] MCH Clock Skew..................................[ 50ps] ******DRAM Performance Control****** Performance Enhance.............................[Standard] Extreme Memory Profile (XMP)....................[ Auto ] (G) MCH Frequency Latch.........................[ 266 ] System Memory Multiplier........................[ 2.50A ] Memory Frequency ..............1066.............1275 DRAM Timing Selectable..........................[ Manual ] CAS Latency Time...............[ 5 ].........[ 5 ] tRCD...........................[ 5 ].........[ 5 ] tRP............................[ 5 ].........[ 5 ] tRAS...........................[ 15 ].........[ 15 ] ******Advanced Timing Control****** tRRD...........................[ 4 ]..........[ Auto ] tWTR...........................[ 4 ]..........[ Auto ] tWR............................[ 6 ]..........[ Auto ] tRFC...........................[ 72 ].........[ 55 ] tRTP...........................[ 4 ]..........[ Auto ] Command Rate (cmd).............[ 0 ]..........[ 2 ] ******Channel A Timing Settings****** Static tRead Value [ 8 ] ................[ 8 ] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel A Driving Settings****** Drive Strength Profile..........................[ Auto ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Channel B Timing Settings****** Static tRead Value [ 8 ] ................[ 8 ] tRD Phase0 Adjustment [ 0 ] ................[ Auto ] tRD Phase1 Adjustment [ 0 ] ................[ Auto ] tRD Phase2 Adjustment [ 0 ] ................[ Auto ] tRD Phase3 Adjustment [ 0 ] ................[ Auto ] tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ] tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ] tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ] tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ] Dimm 1 Clock Skew Control.......................[ Auto ] Dimm 2 Clock Skew Control.......................[ Auto ] DDR Write Training..............................[ Auto ] ******Channel B Driving Settings****** Drive Strength Profile..........................[ Auto ] Data Driving Pull Up Level......................[ Auto ] cmd Driving Pull Up Level.......................[ Auto ] ctrl Driving Pull Up Level......................[ Auto ] clk Driving Pull Up Level.......................[ Auto ] Data Driving Pull Down Level....................[ Auto ] cmd Driving Pull Down Level.....................[ Auto ] ctrl Driving Pull Down Level....................[ Auto ] clk Driving Pull Down Level.....................[ Auto ] ******Motherboard Voltage Control****** Load-Line Calibration...........................[ Enabled ] CPU Vcore [ 1.25 ]...................[ 1.418V ] CPU Termination [ 1.20 ]...................[ 1.40 ] CPU PLL [ 1.50 ]...................[ 1.57 ] CPU Reference [ 0.760 ]...................[ 0.911 ]ET6 0.785 MCH Core [ 1.100 ]...................[ 1.44 ] MCH Reference [ 0.760 ]...................[ 0.926 ]ET6 0.80 MCH/DRAM Refernce [ 0.900 ]...................[ Normal ] ICH I/O [ 1.500 ]...................[ Normal ] ICH Core [ 1.100 ]...................[ Normal ] DRAM Voltage [1.8]...................[2.20 ] DRAM Termination [0.9]...................[Normal] Channel A Ref [0.9]...................[Normal] Channel B Ref [0.9]...................[Normal] *****************Advanced BIOS Features********* Limit CPUID Max to 3 ................. [disable] No-Execute memory Protect ............ [disable] CPU Enhance Halt (CIE) ............... [disable] C2/C2E State Support ................. [disable] C4/C4E State Support ................. [disable] CPU Thermal Monitor................... [disable] CPU EIST Function..................... [disable] Virtualization Technology ............ [disable]
Reply With Quote
Bookmarks