Right now this is about as fast as I can get it stable..Originally Posted by C-N
Have you been into windows @ 1000 or so & had a look at what the board is setting auto using memset? Perhaps tRFC is too tight or maybe even the performance level too low.
I also found adjusting the DRAM Skews & RCOMP models allowed me to boot 4 1gb sticks well over 1200mhz & 2.4v
I am sure I seen OCZ Tony running 8gb of something at a decent speed on either a P35,X38,X48 or P45 DFI (which all play about the same) have you has a search/google about for people running 8gb on one of these DFI's?
CNCode:Thermal Management Control.......... - Disabled PPM(EIST) Mode...................... - Disabled Limit CPUID MaxVal.................. - Disabled CIE Function........................ - Disabled Execute Disable Bit................. - Disabled Virtualization Technology........... - Disabled Core Multi-Processing............... - Enabled >DRAM Timing: Enhance Data transmitting........... - Auto Enhance Addressing.................. - Auto T2 Dispatch......................... - Auto >Clock Setting Fine Delay Press Enter: DLL And RCOMP Settings.............. - Auto Ch1 Dram Defaul Skew................ - Model 0 Ch2 Dram Defaul Skew................ - Model 0 RCOMP Settings...................... - Model 2 Fine Delay Step Degree.............. - 70ps Ch1 Clock Crossing Setting.......... - Auto DIMM1 Clock Fine Delay.............. - Current[1346ps] DIMM2 Clock Fine Delay.............. - Current[1346ps] Ch1 Control0 Fine Delay............. - Current[166ps] Ch1 Control1 Fine Delay............. - Current[166ps] Ch1 Control2 Fine Delay............. - Current[124ps] Ch1 Control3 Fine Delay............. - Current[110ps] Ch1 Command Fine Delay.............. - Current[262ps] Ch2 Clock Crossing Setting.......... - Auto DIMM3 Clock Fine Delay.............. - Current[1346s] DIMM4 Clock Fine Delay.............. - Current[1346ps] Ch2 Control0 Fine Delay............. - Current[14ps] Ch2 Control1 Fine Delay............. - Current[56ps] Ch2 Control2 Fine Delay............. - Current[0ps] Ch2 Control3 Fine Delay............. - Current[0ps] Ch2 Command Fine Delay.............. - Current[110ps] Ch1 Ch2 Common Clock Setting........ - Auto Ch1 RDCAS GNT-Chip Delay............ - Auto Ch1 WRCAS GNT-Chip Delay............ - Auto Ch1 Command To CS Delay............. - Auto . Ch2 RDCAS GNT-Chip Delay............ - Auto Ch2 WRCAS GNT-Chip Delay............ - Auto Ch2 Command To CS Delay............. - Auto Flex Memory Mode..................... - Auto CAS Latency Time (tCL)............... - 5 RAS# to CAS# Delay (tRCD)............ - 5 RAS# Precharge (tRP)................. - 5 Precharge Delay (tRAS)............... - 15 All Precharge to Act................. - Auto REF to ACT Delay (tRFC).............. - Auto Performance Level.................... - Auto >Read delay phase adjust Press Enter: Channel 1 Phase 0 Pull-In........... - Auto Channel 1 Phase 1 Pull-In........... - Auto Channel 1 Phase 2 Pull-In........... - Auto Channel 1 Phase 3 Pull-In........... - Auto Channel 1 Phase 4 Pull-In........... - Auto Channel 2 Phase 0 Pull-In........... - Auto Channel 2 Phase 1 Pull-In........... - Auto Channel 2 Phase 2 Pull-In........... - Auto Channel 2 Phase 3 Pull-In........... - Auto Channel 2 Phase 4 Pull-In........... - Auto Write to PRE Delay (tWR)............ - Auto Rank Write to Read (tWTR)........... - Auto ACT to ACT Delay (tRRD)............. - Auto Read to Write Delay (tRDWR)......... - Auto Ranks Write to Write (tWRWR)........ - Auto Ranks Read to Read (tRDRD).......... - Auto Ranks Write to Read (tWRRD)......... - Auto ALL PRE to Refresh.................. - Auto >Voltage Settings: CPU VID Control..................... - Auto 1.3450v CPU VID Special Add................. - Disabled CPU VID Special Add................. - 110.15% DRAM Voltage Control................ - 2.21v SB Core/CPU PLL Voltage............. - 1.55v NB Core Voltage..................... - 1.322v CPU VTT Voltage..................... - 1.200v Vcore Droop Control................. - Disabled Clockgen Voltage Control............ - 3.45v GTL+ Buffer Strength................ - Strong CPU GTL 0 REF Volt.................. - 0.6250 CPU GTL 2 REF Volt.................. - 0.6250 CPU GTL 1 REF Volt.................. - 0.6250 CPU GTL 3 REF Volt.................. - 0.6250 North Bridge GTL 0 REF Volt......... - 0.6250 North Bridge GTL 1 REF Volt......... - 0.6250 FSB Vref............................ - Auto Genie BIOS Settings: Exist Setup Shutdown................ - Mode 2 Exist Shutdown After AC loss........ - Enabled AC Shutdown Free.................... - Enabled O.C Clock Fail Retry Counter........ - 1 O.C Clock Fail CMOS Reloaded........ - Disabled CPU Clock Ratio..................... - 10 Target CPU Clock.................... - 3400 MHz CPU Clock........................... - 340 Boot Up Clock....................... - Auto CPU Clock Amplitude................. - 800mV CPU Clock0 Skew..................... - 100ps CPU Clock1 Skew..................... - 100ps DRAM Speed.......................... - Auto (A manual set at any ratio crashes) Target DRAM Speed................... - 1022MHz PCIE Clock.......................... - 100mhz PCIE Slot Config.................... - 1x 1x CPU Spread Spectrum................. - Disabled PCIE Spread Spectrum................ - Disabled
Reply With Quote
Bookmarks