ASUS Maximus II Formula - new P45 king?

[meangreenxp]

Greetings,

Recently I replaced a dead P5W DH deluxe with the M2F. With the P5W I was able to overclock my Q6600 G0 to 3.4GHZ with 24/7 stability for over a year before my motherboard died. The M2F has a great deal of BIOS settings for the overclocker, however the manual doesn't give a detailed explanation of each setting. I have searched the this awesome forum as well as other to get my OC to 3.6Ghz, however it is not 100% stable. I am able to run Prime, Orthos, Everest successfully without any errors, but at times I get the BSOD with trying to put my virtual machine in suspend mode, or attaching certain USB hard drives with a NTFS.SYS error. I would like to get some opinions / suggestions on :

1. voltage settings
2. DRAM Skew settings
3. Mem OC charger / Twister / Booster
4. PCIE fREQ
5. CPU and Mem GTL References
6. various CPU settings

Here is my current BIOS settings:

Asus Maximus Formula II Bios 1307
Crucial Ballistix DDR2PC6400 (4X1GB)
Corsair TX750W PSU
Cpu Q6600 G0

Ai Overclock Tuner: Manual
OC From CPU Level Up: Auto
Ratio CMOS Setting: 9
FSB Frequency: 400
CPU Clock Skew: auto
NB Clock Skew: auto
FSB Strap to North Bridge: 333
DRAM Freq: DDR2-801Mhz
DRAM CLK Skew on Channel A1: Auto
DRAM CLK Skew on Channel A2: Auto
DRAM CLK Skew on Channel B1: Auto
DRAM CLK Skew on Channel B2: Auto
DRAM Timing Control: Manual
 1st Information: 5-5-5-15-3-52-6-3
  CAS# Latency : 5
  RAS# to CAS# Delay : 5
  RAS# Precharge : 5
  RAS# ActivateTime : 15
  RAS# to RAS# Delay : auto
  Row Refresh Cycle Time : auto
  Write Recovery Time : auto
  Read to Precharge Time : auto
 2nd Information : 8-3-5-4-6-4-6
  Read to Write Delay (S/D) :auto
  Write to Read Delay (S) : auto
  Write to Read Delay (D) : auto
  Read to Read Delay (S) : auto
  Read to Read Delay (D) : auto
  Write to Write Delay (S) : auto
  Write to Write Delay (D) : auto
 3rd Information : 14-5-1-6-6
  Write to PRE Delay : auto
  Read to PRE Delay : auto
  PRE to PRE Delay : auto
  ALL PRE to ACT Delay : auto
  ALL PRE to REF Delay : auto

DRAM Static Read Control: Disable
Dram Read Training : Disable
MEM OC Charger : auto
Ai Clock Twister : light
Transaction Booster : auto
PCIE Freq: 100

CPU volt:1.45625
CPU PLL Voltage: 1.50000
FSB Termination Voltage: 1.23250
DRAM Voltage: 2.19750
North Bridge Voltage: 1.23250 
SB 1.5 Voltage: 1.51325
SB 1.1 Voltage: 1.12650

CPU GTL Reference 0 : auto
CPU GTL Reference 1 : auto
CPU GTL Reference 2 : auto
CPU GTL Reference 3 : auto
North Bridge GTL Reference : AUTO
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
North Bridge DDR Reference : AUTO


Ratio CMOS Setting: 9
C1E Support: Disabled
Max CPUID Value Limit: Disabled
Intel Virtualization Tech: Enabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled

Load-Line Calibration: enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled 

Thank you for your input it will be helpful for myself and others I am sure.