Asus M3A79-T Deluxe

[XRogerX]

well i got everything install , but i do have a question everest is showing me these readings , does this look wrong for temps and volt

Field Value
Sensor Properties
Sensor Type ITE IT8720F (ISA E80h)
GPU Sensor Type Diode (ATI-Diode)
Chassis Intrusion Detected Yes

Temperatures
Motherboard 34 °C (93 °F)
CPU 22 °C (72 °F)
CPU #1 / Core #1 21 °C (70 °F)
CPU #1 / Core #2 18 °C (64 °F)
Aux 38 °C (100 °F)
GPU Diode (DispIO) 42 °C (108 °F)
GPU Diode (MemIO) 49 °C (120 °F)
GPU Diode (Shader) 44 °C (111 °F)
Seagate ST3250820AS 37 °C (99 °F)
Seagate ST3320620AS 42 °C (108 °F)
WDC WD3200AAJS-65RYA0 46 °C (115 °F)

Cooling Fans
CPU 2213 RPM
Chassis 2090 RPM
Power Supply 2064 RPM
GPU 3636 RPM

Voltage Values
CPU Core 1.41 V
+2.5 V 3.01 V
+3.3 V 3.26 V
+5 V 4.92 V
+12 V 9.98 V
+5 V Standby 4.95 V
VBAT Battery 3.34 V


PC Probre is showing me these temps and Volts

VCore - 1.41V
+12V - 12.03v
+5V - 4.92V
+3.3V - 3.26V
CPU TEMP - 37C
MB TEMP - 34C
CPU FAN - 2213
CHASSIS FAN - 2089
CHASSIS2 FAN - 2070

[XRogerX]

anyone?

[demonkevy666]

anyone?

everst hasn't got the 12volt right on any AMD board so far pc probe is correct.

somethings aren't always right.

[Chicken Patty]

everst hasn't got the 12volt right on any AMD board so far pc probe is correct.

somethings aren't always right.

i think however that PC probe temp readings are wrong. it reads about 10ºc higher than everything else.

[MattiasNYC]

Two quick questions I didn't find answers to;

So has anybody has any success running 8GB at 1066?

And if it's not possible is one better off running 8GB with 800 memory instead?

[Chicken Patty]

Two quick questions I didn't find answers to;

So has anybody has any success running 8GB at 1066?

And if it's not possible is one better off running 8GB with 800 memory instead?

most i've ran at 1066 is 2 gigs which is what I run now.

[Jaivan]

most i've ran at 1066 is 2 gigs which is what I run now.

I got 8GB at 1100 5-5-5-16 (no 15 option in bios) on my current board in my sig and has 8GB at 1066 on the M3A79-T

[merkk1]

Well running Men. at 1066 may not be the fastes set-up . For me running my men. @ 1000 and 2500 NB/HT linkspeed is faster than running my men. at 1066 2000 NB/HT link speed . I can not over clock my men. hight enought @ 1066 to beat out the 1000 2500 NB/HT link speed setup . Just something to think about .

[MattiasNYC]

Thanks guys - you rock - I really appreciate it!

[Chicken Patty]

^^ no problem mattias, count on us anytime

[RiverRicer]

everst hasn't got the 12volt right on any AMD board so far pc probe is correct.

somethings aren't always right.

Correct me if I'm wrong, but I believe that Everest and some other voltage monitoring software don't read the 12v correctly if your P/S has multiple 12v rails.

[XRogerX]

well i got my 9950 be today with my Zalman 9700 now to work with the overclock for this

Is anyone running this on Air and overclocked?

[pinoyxpryde]

well i got my 9950 be today with my Zalman 9700 now to work with the overclock for this

Is anyone running this on Air and overclocked?

lots of people, not many with the zalman though i dont think.

[XRogerX]

my memory is running @ddr2 800 so i would have to change this to 533 for ddr2 -1066 ?

[Cyben]

With the new 504 Bios, I was able to go from 3.3 to 3.4 ghz.
M3A79-t

[XRogerX]

With the new 504 Bios, I was able to go from 3.3 to 3.4 ghz.
M3A79-t

im not touching the bios , the last time i did i messed my board so im leaving it alone lol

[demonkevy666]

Correct me if I'm wrong, but I believe that Everest and some other voltage monitoring software don't read the 12v correctly if your P/S has multiple 12v rails.

don't know I never use it anyways. lol

[gOtVoltage]

don't know I never use it anyways. lol

HWmonitor seems to work best.

[demonkevy666]

HWmonitor seems to work best.

all I was getting on that was my hard drive.

now I'm getting all of it wth.... :/

damn vista

[tbone8ty]

im not touching the bios , the last time i did i messed my board so im leaving it alone lol

u probably have to set yur bios to show 1066...most mobos u have to do this i think

[XRogerX]

so i have to set it to what in the bios? 1068?

[gOtVoltage]

so i have to set it to what in the bios? 1068?

Wow how did i miss that Sig... A X2 will not run in 1066 mode...You must raise the HTT to 266 and use a low ram divider to get 1066mhz..

266x2(half divider i believe is 400ram divider so setting ram too 400 and raising HTT to 266 should work...keep the HT @ around 2000 untill you get your ram where you want it..

266HTT and 400ram divider = 532x2 = 1064mhz(1066ram)

I forgot Only Phenoms IMC/integrated memory controler can use the 1066 divider most any Bios ,,unless you have a 2xcore Phenom..K10 the IMC then can access 1066..

If you are using a X2 like in your sig..You must use High HTT to achieve high freqency ram...Youll set your ram timing and the Volts@ the specs of your ram for 1066..

If you dont know what timing to use,,Install CPU-Z and in Memory Tab it will show the timing your curently at..In SPD tab it will show volts/timing to set if your Ram has a EPP setting

Hope that helps ya,
gOtVolTage

P.S. Phenom can run HTT292 with this Mobo,, X2's can run 320+htt..so youll be able to use 266+HTT,, just lower your HT and ram divider till you get to 266htt and 1064mhz on the ram. the Higher the HTT the lower CPU multi you need to set also.

UPDATED,, UPDATED,,
Crap change your sig to Phenom! You had me comfused,,

The info Posted above applies if you cant use 1066 divider or have a X2,,

Set the ram in you Bios to what ever setting is close to 1066 with out going over 1066mhz...The Bios will show exactly what freqency your ram will run(be set at) with each Ram divider if you select manual divider and timing

[XRogerX]

oops sry i forget to change it i have a 9950BE Phenom lol

Ok Fixed

[gOtVoltage]

oops sry i forget to change it i have a 9950BE Phenom lol

Ok Fixed

Its cool been there done that ..

Hope it works.

Your settings will look something like this,,
The higher you adjust the HTTabove 200 it will readjust the dividers to read what your ram will be set to..Keep it at 1066 or lower unless you know the ram clocks above 1066..

Make shure you set the correct volts for your ram to run 1066..some chips have a higher volt value to run 1066 instead of 800. My vipers run 800 @ 1.8volts and 1200 @ 2.3volts. Each Ram manufactur is different when it comes to Volts running 1066.

[XRogerX]

ok i will check , ty for working with me

Ok i just checked mine and i have 400 , 533 ,667 ,800 and 1068