Official GIGABYTE X38-DQ6/X38T-DQ6 Info/BIOS Thread

[TyphooN]

Robust Graphics Booster: AUTO
CPU Clock Ratio: 9X
CPU Host Clock Control: Enabled
CPU Host Frequency(Mhz) : 412
PCI Express Frequency (Mhz) : 100
C.I.A.2 Disabled
Performance Enhance :Extreme
System Memory Multiplier (SPD) 2.40B
Memory Frequency(Mhz):989(501MHz in memset? o.O)
DRAM Timing Selectable :Manual
Standard Timing Control
CAS Latency Time: :5
DRAM RAS# to CAS# :5
DRAM RAS# Precharge :3
Precharge Delay(tRAS) :13
Advanced Timing Control
ACT to ACT Delay(tRRD) :2
Rank Write to READ Delay :3
Write To Precharge Delay :3
Refresh to ACT Delay :43
Read To Precharge Delay :1
tRD :7
tRD Phase Adjustment :13
Command to #CS Timing: : 2T
Clock Driving and Skew Control
CPU/PCIEX Clock Driving Control : 800mv
CPU Clock Skew Control :Normal
(G)MCH Clock Skew Control :Normal
System Voltage Control
DDR2 OverVoltage Control :+0.25v
PCI-E OverVoltage Control :Normal
FSB OverVoltage Control :+0.15v
(G)MCH OverVoltage Control :+0.15v
Loadline Calibration: Enabled
CPU Voltage Control: 1.54375V

CPU is a Q6600, Memory is G.Skill PC8000 2x2gb. I thought that I had it stable with the 2.66D strap with these settings but I could not make it 100% stable, which isn't good enough for me for a 24/7 setting. Richard try out these timings as they are as tweaked as I can get them for this speed.

[truehighroller]

Robust Graphics Booster: AUTO
CPU Clock Ratio: 9X
CPU Host Clock Control: Enabled
CPU Host Frequency(Mhz) : 412
PCI Express Frequency (Mhz) : 100
C.I.A.2 Disabled
Performance Enhance :Extreme
System Memory Multiplier (SPD) 2.40B
Memory Frequency(Mhz):989(501MHz in memset? o.O)
DRAM Timing Selectable :Manual
Standard Timing Control
CAS Latency Time: :5
DRAM RAS# to CAS# :5
DRAM RAS# Precharge :3
Precharge Delay(tRAS) :13
Advanced Timing Control
ACT to ACT Delay(tRRD) :2
Rank Write to READ Delay :3
Write To Precharge Delay :3
Refresh to ACT Delay :43
Read To Precharge Delay :1
tRD :7
tRD Phase Adjustment :13
Command to #CS Timing: : 2T
Clock Driving and Skew Control
CPU/PCIEX Clock Driving Control : 800mv
CPU Clock Skew Control :Normal
(G)MCH Clock Skew Control :Normal
System Voltage Control
DDR2 OverVoltage Control :+0.25v
PCI-E OverVoltage Control :Normal
FSB OverVoltage Control :+0.15v
(G)MCH OverVoltage Control :+0.15v
Loadline Calibration: Enabled
CPU Voltage Control: 1.54375V

CPU is a Q6600, Memory is G.Skill PC8000 2x2gb. I thought that I had it stable with the 2.66D strap with these settings but I could not make it 100% stable, which isn't good enough for me for a 24/7 setting. Richard try out these timings as they are as tweaked as I can get them for this speed.

Go to this site and read and it will help you alot with your settings as they are off and you have tooooo... much voltage going to the cpu!! you have everything I do basicaly check my sig... Here is the site,

http://www.clunk.org.uk/forums/revie...-dq6-blog.html