Results 1 to 25 of 1681

Thread: **Official DFI LanParty UT 790FX-M2R Review/Overclock/Guide Thread**

Threaded View

  1. #11
    Registered User
    Join Date
    Dec 2007
    Location
    Orlando, FL
    Posts
    49
    Spread Spectrum - Disabled
    CPU Host/HTT Clock - 246MHz
    CPU Host/HTT Boot Up Clock - 230MHz
    CPU Host/HTT Adjust Gap - 2MHz
    PCIE Clock - 100MHz

    Onboard LAN1 - Disabled
    Onboard LAN2 - Enabled
    Onboard 3132 Mode - Disabled

    CPU VID Control - 1.42500V
    CPU VID Special Add - Auto
    CPU NB Voltage Control - 1.30000V
    CPU NB VID Special Add - Auto
    DRAM Voltage Control - 2.07V
    SB PLL 1.2V Voltage - 1.40V
    NB Core Voltage - 1.330 V
    NB PCIE Voltage - 1.120 V
    NB HT Voltage - 1.350 V

    Virtualization - Disabled
    AMD K8 Cool&Quiet control - Disabled
    NPT Fid control - x11
    CPU-NB DID - 1
    CPU-NB FID - 04
    AMD CPU stepping - P0

    HT Link Width - 16bit
    HT Link Frequency - 1.6GHz
    IH Flow-Control Mode - Disabled
    HT Link Tri-State - Disabled
    2x LCLK Mode - Disabled
    UnitID Clumping - Disabled

    Timing Mode - Manual
    Memory Clock Value or Limit - DDR 800
    DCTs Mode - Unganged
    CKE based powerdown - Per Channel
    Memclock tri-stating - Disabled
    2T Mode - Enabled
    CAS Latency Time - 4 CLK
    Precharge delay (tRAS) - 12 CLK
    DRAM RAS# Precharge - 4 CLK
    DRAM RAS# to CAS# Delay - 4 CLK
    Bank to Bank Cmd (TRRD) - 2CLK
    TRC - 16T
    TRTP - 2 CLK - 4 CLK
    Write Recovery (TWR) - 3 CLK
    Write-Read Command (TWTR) - 2 CLK
    TRFC0-3 - 105.0ns
    Trdrd - 2 CLK
    TrwtTO - 3 CLK
    Twrrd - 0 CLK
    Twrwr - 1 CLK
    CS/ODT Pin Fine Delay - Enabled
    TLB Cache Mode - Enabled
    Bank Swizzle Mode - Enabled
    Auto Tweak Performance - Enabled
    Optimal Performance Mode - Enabled
    DRAM Drivers Weak Mode - Normal Drive
    Output Driver Comp. - Auto

    Advanced Chipset Features:
    Memory Hole - Disabled
    Memory Hole Remapping - Enabled
    Auto Optimize Bottom IO - Enabled
    Bottom of (31:24) IO space - C0
    System BIOS Cacheable - Disabled

    Onboard FDC Controller - Disabled
    Onboard Serial Port - Disabled
    Onboard IRDA Select - Disabled
    CIR Port Address - Disabled

    PCIE Configuration:
    Secondary Dual Slot Config - Auto
    P2P b/w Primary/Secondary - Enabled
    GPP Power Limit, W - 25

    GFX Port 1/3/4:
    Gen2 High Speed Mode - Disabled
    Link ASPM - Disabled
    Link Width - Auto
    Slot Power Limit, W - 75
    PCIE GPP Link Width - 2.1.1.1.1

    NB-SB Port Features:
    Link ASPM - Disabled
    VC1 Traffic Support - Disabled

    HD Azalia Audio - Disabled
    OnChip SATA Controller - Enabled
    OnChip SATA Type - Native IDE

    IDE DMA transfer access - Enabled
    Primary IDE Controller - Disabled

    OnChip USB Controller - Enabled
    USB EHCI Controller - Enabled
    OnChip USB KBC Controller - Enabled
    USB Mouse Support - Disabled

    ACPI Suspend Type - S1(POS)
    C2 Disable/Enable - Disabled
    Soft Off by PWRBTN - Instant-Off
    PowerOn by PCI Card - Disabled
    ACPI XSDT Table - Disabled
    HPET Support - Enabled
    POWER ON Function - BUTTON ONLY
    PWRON After PWR-Fail - On
    ATC Alarm Resume - Disabled

    Init Display First - PCIEX
    Resources Controller By - Auto
    PCI/VGA Palette Snoop - Disabled
    Assign IRQ for VGA - Enabled
    Assign IRQ For USB - Enabled
    PCI Latency Timer (Per 8CLK) - 8
    INT Pin 1 to 8 Assignment - Auto
    PCI Express relative items, Maximum Payload Size - 128
    Last edited by Iketh; 01-26-2008 at 10:43 PM. Reason: listed incorrect voltages
    ASUS Maximus IV Gene-Z/Gen 3
    Intel 2600K 3117B310 @ 4400MHz, ~1.35v (+0.06 offset, 0% LLC), 1.8v PLL, P95 27.7
    G.Skill 2x4GB @ 2133MHz, 10-11-11-30-2t, 1.6v BIOS
    Saphire 6870 @ 940/1140
    Intel SSD X25-M 80GB
    Seagate ST1000DM003
    Seasonic SS-460FL Active PFC F3 Fanless
    Cooler Master Hyper 212 Evo w/ 2x120mm Gelid WING12PL
    SilverStone TJ08B-E

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •