D-tek nozzles

[RickCain]

What is Shizzle ?

the goods, the best, ftw, etc

[nikhsub1]

What is Shizzle ?

Well technically it is slang. In this instance it is meant to convey 'the bomb' or 'la bomba' or in simpler words 'very good'.

[Jedda]

Combo of sizzle and a word I can't get past the frolicing fruit.
Translates as 'hot sh..'

[disruptfam]

hot sizzle!!!!!

[the highlander]

Sadly... using the qcore nozzles... no change... 0 difference...

[disruptfam]

Sadly... using the qcore nozzles... no change... 0 difference...

wow.... a few people are getting zero improvement with the quad nozzle... that suck's

[pak]

SOmeone put the 4.5 on a quad.

--pak

[911us]

Well technically it is slang. In this instance it is meant to convey 'the bomb' or 'la bomba' or in simpler words 'very good'.

oh..I got it,yes it is "shizzle"

[LinusTech]

SOmeone put the 4.5 on a quad.

--pak

I'll get around to it eventually, but I've been busy. I'm sure Scott will release results in 4-6 months (j/k man... ) if you can wait for his.

[dembones]

installed the quad nozzle last night, noticing about a 1 degree change, but still waiting on TIM to settle

[iadstudio]

I know mx-2 says faster curing times, but what is the best way to cure it and how long should it take?

???

[AndyM]

I cant decide if I should put a second pump in my loop while installing these nozzles. I played around with the flow charts some, and still cant decide if getting more operating pressure would be beneficial or not. So here's what I got...D5 pump pushing through a Fuzion, EK G80 block, MCW30, and 2 EK Mosfet blocks. Add in 2 PA rads and 2 restrictive looking elbows to this mess. I'm kinda thinking more pressure for more 'squirt' might be a good idea here, so whatcha guys think...I have room for a second D5, should I or not? Are you guys with fairly loaded up loops finding the 1-2C gains those on CPU only loops are getting with the nozzles?

[marauder16]

I cant decide if I should put a second pump in my loop while installing these nozzles. I played around with the flow charts some, and still cant decide if getting more operating pressure would be beneficial or not. So here's what I got...D5 pump pushing through a Fuzion, EK G80 block, MCW30, and 2 EK Mosfet blocks. Add in 2 PA rads and 2 restrictive looking elbows to this mess. I'm kinda thinking more pressure for more 'squirt' might be a good idea here, so whatcha guys think...I have room for a second D5, should I or not? Are you guys with fairly loaded up loops finding the 1-2C gains those on CPU only loops are getting with the nozzles?

make two loops?

[Petra]

I'm sure Scott will release results in 4-6 months (j/k man... ) if you can wait for his.

If there's anyone around here who deserves to get poked fun at for taking forever, it would be me... After all, the only people who have even seen performance data from my live CPU/TTV combo testbed are Quoc and a few people over at Enzotech.

I'm getting there, though... slowly but surely... plodding along...

[maxwedge]

I just got a new block and nozzle kit from sidewinder, took it apart to put the intake seal in and couldn't believe black silicone was used between the top plate and the o-ring! What a waste of a perfectly good good o-ring.

If it don't leak then whatever I guess. Nice block though otherwise.

[iadstudio]

I don't think it's silicone, it's just injection molded in the block. it's a good idea to clean up the excess injection meterial before you assemble the loop.

[maxwedge]

No it's silicone. I work with the stuff. Looks to me like an assembly line procedure to simplify assembling them but what the hey...if it don't leak then it's ok.

I just don't believe in using silicone with a good rubber gasket.

[iadstudio]

so are you saying the entire gasket is silicone?

[Petra]

Looks to me like an assembly line procedure to simplify assembling them but what the hey...if it don't leak then it's ok.

That's exactly what it is... you get a prize (and, no, it's not cake)

<-- prize

[Martinm210]

That's exactly what it is... you get a prize (and, no, it's not cake)

<-- prize

[axemanrio]

Any idea where the nozzle kits are available in UK?

[Waterlogged]

No it's silicone. I work with the stuff. Looks to me like an assembly line procedure to simplify assembling them but what the hey...if it don't leak then it's ok.

I just don't believe in using silicone with a good rubber gasket.

...and if I had to venture a guess as to which silicone, it'd be RTV Black from Permatex.

[911us]

I got 2 packs from Petra this week and I planned to use them for my 2 quads but it seem like no improvement throught some reports.Should I install quad nozzles ?

[maxwedge]

so are you saying the entire gasket is silicone?

No, the gasket is rubber its just that it's glued to the top with black silicone which is unnecessary with a rubber gasket. It's no big deal, I was just stating something I'm seeing and I don't know if they all came that way. I'll take a pic after work tomorrow.

..and if I had to venture a guess as to which silicone, it'd be RTV Black from Permatex.

If I could tell that (brand) then I could make a lot more money than what I do now doing something else.

[iadstudio]

ooooooooooh. Someone told me it was an injection molded washer. I saw the silicone mess just the same and shaved it away after I took the block apart. That makes more sense. Thanks for the explanation.

BTW. Not saying I know this first hand or anything, but a little solicone in your DDC impeller might make it pretty noisy and cause you to think it's failing. Just saying, it could happen