G.SKILL PIS F3-17600CL7D-4GBPIS 2200 7-10-10-28 1.65V P55 Series

[SimpleTECH]

Just got a hold of my kit that came directly from G.Skill. Major props to TweakTown for the gift.

Ordered a P55 board last night, so no testing until next week.

I wonder if I could get some decent results out of my X58?

[DeDaL]

Just recieved this sticks week ago.

Very interesting one.

Guys, do you have problems with command rate and dual chanel mode ?

[devil_mcry]

I´dont know..
are renamed.
I´ve posted foto of ICS on this thread

but hs gskill eco same ics of this?
i read this online...

[DeDaL]

Starting to play.....

2600(9-11-9-28-1T-6-90)@1.72v

http://valid.canardpc.com/show_oc.php?id=933433

[borec]

but hs gskill eco same ics of this?

I think no. Eco has new chips... maybe 40nm elpida

to DeDaL:
what problem with CR and dual? I haven´t any problems...
and 2600MHz is great can pass SPI 1M or 32M?

[hiwa]

but hs gskill eco same ics of this?
i read this online...

MY personal Idea :

They are same but different category, means for example Elpida sell mem manufactories BBSE but are all BBSEs are same?
they have a lot of categories with same name, manufactories binn good ic for their highend product (Class A), and ...


all memories from 1600 cl6 to 2250 cl8 are Hyper but they are not same in performnace as we saw before.


PIS is binned IC from last IC's and ECO is mainstream series.


BTW nice freq Dedal cpu under cold?

[DeDaL]

borec The problem is setting high freq at low CL, but prolem is all about CPU's IMC. When you set different Command Rates for cannels, it can helps me to set +70-80MHz with fully working dual channel mode.

hiwa thanks, cpu and memory is still on air. I need to do more preporation before do some subzero job
Did your sticks scaling after 1.72v ?

[hiwa]

borec The problem is setting high freq at low CL, but prolem is all about CPU's IMC. When you set different Command Rates for cannels, it can helps me to set +70-80MHz with fully working dual channel mode.

hiwa thanks, cpu and memory is still on air. I need to do more preporation before do some subzero job
Did your sticks scaling after 1.72v ?

Max on air 1.76 no problem, but when i touch HS was damn Hot !!!
Waiitng for some damage dude

[ci2kla]

Max on air 1.76 no problem, but when i touch HS was damn Hot !!!
Waiitng for some damage dude

I was wondering if this kit will be compatible with EVGA 4X Classified E762... which can do CAS 6 @2Ghz...

[GSKILL TECH]

Should be quite impressive on a E762. Will definitely be compatible.

Thank you
GSKILL TECH

[hiwa]

I was wondering if this kit will be compatible with EVGA 4X Classified E762... which can do CAS 6 @2Ghz...

sorry my second kit sent for review
when they back i'll try for sure

[DeDaL]

Less vDDR - 1.70v
Single channel.

2668MHz(9-11-11-31)

All air
http://valid.canardpc.com/show_oc.php?id=936000

[borec]

nice !!!
go for ln2

[DeDaL]

Thanks bro.



It is somthing wrong with official F6 bios for P55-UD6, cant enable 2200CL7(7-10-10-28) at 1.65v
With F6b bios there are no problem.

[ci2kla]

sorry my second kit sent for review
when they back i'll try for sure

Thanks bro

[devil_mcry]

I think no. Eco has new chips... maybe 40nm elpida

to DeDaL:
what problem with CR and dual? I haven´t any problems...
and 2600MHz is great can pass SPI 1M or 32M?

MY personal Idea :

They are same but different category, means for example Elpida sell mem manufactories BBSE but are all BBSEs are same?
they have a lot of categories with same name, manufactories binn good ic for their highend product (Class A), and ...


all memories from 1600 cl6 to 2250 cl8 are Hyper but they are not same in performnace as we saw before.


PIS is binned IC from last IC's and ECO is mainstream series.


BTW nice freq Dedal cpu under cold?

ok :\ however this kit is very good when I bought the DDR3 me, these were not available

[borec]

I think ECO is very good mems. Some times a little better than PIS, especially with lower timing. But I think his life is very degraded when you pull it on 1,65V+

[devil_mcry]

I think ECO is very good mems. Some times a little better than PIS, especially with lower timing. But I think his life is very degraded when you pull it on 1,65V+

me too :\ if these have new ics it is sure :|

[SF3D]

I will post here few screens from my tests, cause there is no point doing new thread. I got this kit last week after two week delay. Fedex did not do their job as good as usually.

I used cheap ASUS P7P55D Pro motherboard and my i7 870 is the worst of it's kind. On this board, absolutely max bclk is 213MHz

This issue was limiting my tests quite badly, when I tried to find the maximum stable clockspeeds.

These following results should be easily repeatable in any setup, cause my system parts are so crappy.

Setup:

2x2GB G.Skill F3-17600CL7D-4GBPIS (DDR3 2200 7-10-10-10-28 1.65V)
ASUS P7P55D Pro
Intel Core i7 870
Thermaltake 1200W TP
ATI Radeon 4890
Noctua NH12 cooler
Win vista 32-bit

Few Pictures:



Results:

6-9-6 @ 1000MHz ( 1.65V / 1.4Vtt)


6-9-6 @ 1045MHz (1.7V /1.4Vtt)


7-10-7 @ 1100MHz (1.65V / 1.4Vtt)


7-10-8 @ 1150MHz (1.7V / 1.4Vtt)


8-11-10 @ 1250MHz (1.74V / 1.4375V)


After this CL 8 run my BCLK was getting too unstable. This CPU just can't do more on this board

Will need to try later on some more suitable mobo + CPU combo.


Very easy memory kit from G.Skill
Special thanks to Frank!

[dro]

DAMNNNNNNNNNN!

Thank you for showing me that ram can run smoothly on asus p55.
I'm getting one soon then!

[dro]

Anybody tried this kit with MSI GD65?
From the product website, it states that it works with GD80

[GSKILL TECH]

Works great on the GD 55 and 65 as well.

Thank you
GSKILL TECH

[hiwa]

Nice clocks petri, asus is not good for high bclk

[dro]

GSKILL TECH

Thanks there mate!

[kagula323]

anyone know if these F3-17066CL9T-6GBPS are elpida hyper? or how are they clocking on x58? (I have a Gigabyte X58A-UD7 mobo and I7 920)