G.SKILL PIS F3-17600CL7D-4GBPIS 2200 7-10-10-28 1.65V P55 Series

[ZenEffect]

Very good work and interesting result- I haven't made further tests on mini aus yet or on UD5 which I got today, with celeron 530 will be difficult anyway as low frequency is not interesting. The 2133 9-9-9 run with about 1,5V no matter which cpu frequency, but as for benching even 8-9-8 is too slow I will rather test some hyper if 8gigs run at good speed and timings, seems to be the easier way

it seems that a bit more work needs to be done to achieve c7, however.... c8 2200+ is definately doable with all 4 slots occupied. this is going off topic since the ram im currently testing is in another gskill thread. http://www.xtremesystems.org/forums/...=1#post4962438

[El Gappo]

May of dropped a channel, not checked, first boot with new old sticks

[badatgames18]

@ el gappo.. very nice on amd! vdimm?

i'll be testing the newer 2200cl7 black pcb vs the older 2200cl7 green pcb.
you guys think there will be any difference? are they both the same pcb with different colors or different?




nope the green pcb seems to be same thing

how were the older posts getting tRCD 9

[ZenEffect]

since these are psc based kits, its asking quite a bit to get them to trcd 9 1.65v.

[badatgames18]

since these are psc based kits, its asking quite a bit to get them to trcd 9 1.65v.

i understand, but previous members were able to get 2k with 6-9-6 only 1.65v... i can't even get 7-9-7

i can boot, but very unstable... maybe those guys got lucky and got bbse or something

i have 2 sets of these.. both can't do it, maybe third time is the charm?

[sin0822]

I can't get down to 9 either. Maybe they went subzero?

[badatgames18]

I can't get down to 9 either. Maybe they went subzero?

i don't think so sin.. if you look back.. a few got 6-9-6 28 1T with 1.65v 2000MHz+
i can't even get close to that... they must have been different ic.. most likely bbse. We have meh psc modules

examples:

2220 CL6 Max everest test with 1.65V Vdimm

6-9-7-27-72 with +2200Mhz seems to give good bandwidth

And that ? +2400Mhz CL6 SS done

All on air ... but Vdimm to 1.78V

snip

2100 6-9-6-28 1t 1.65
3dmarks passed

and more on the previous pages

[BeepBeep2]

There are several revisions and dies of PSC, however for the most part they act the same.

My kit did 6-10-6-27 @ 2100 on AMD, however at 1.77v. CL and tRCD are weak, especially tRCD. 2000 6-9-6 was doable in 32M, however at 1.75v

[sin0822]

I can get 6,10,7,28 T1 at 2200. Just not tighter until 2000. I might move them over to llano to see how they really run.

[ZenEffect]

well, its not really a apples to apples comparison when comparing p55 to p67/z68. imc on sandy is alot harsher than on lynnfield/clarkbar. p55 6-9-6 is entirely feasable with psc... not so much on p67/z68

[sin0822]

maybe SB-E will be better. We will see in about a month.

[badatgames18]

just bought some F3-16000CL7D-4GBPIS rated for 2000mhz 7-9-7

as soon as i get them on monday.. will post the results and compare with the 2200cl7
just hope they aren't to degraded from previous owner :/

anyone have these? i'm hoping they are binned higher than the 2200cl7

[websmile]

I don't know if psc is so tight anyway, at least if I look at hese for example

I should have bought some heatspreaders for these and then sell them at 2200 C7 or 2133 C7-10-7 :p

[ZenEffect]

2200 7-10-7-25 1T should be possible @ 1.65v with most kingston and gskill pi or black ripjawsX 2200 kit. what voltage is that at websmile?

[BeepBeep2]

He was at 1.65v

[badatgames18]

yep.. all the pi i have are able to do 7-10-7 easy... 7-10-7 2250+ blck limited was fine for me @ 1.65v


psc is not tight at all.. especially on sandy. 6-10-6 was the best i can do with my 2200cl7 pi kit.. green pcb.. however my black pcb can do 6-9-6 with 1.82v don't know where my screen shot is for that though lol

i don't remember but i saw someone post something about psc doing 6-9-6 with 1.72v and my goal is to find one
hoping the 7-9-7 2000mhz pi will do it or the gskill flare 7-9-7 2000mhz that will be comming in sometime this week also...

going to post results when i get home

I don't know if psc is so tight anyway, at least if I look at hese for example

I should have bought some heatspreaders for these and then sell them at 2200 C7 or 2133 C7-10-7 :p

i just noticed the spd! is that stock or was it flashed lol.. very nice find!

[websmile]

yep.. all the pi i have are able to do 7-10-7 easy... 7-10-7 2250+ blck limited was fine for me @ 1.65v


psc is not tight at all.. especially on sandy. 6-10-6 was the best i can do with my 2200cl7 pi kit.. green pcb.. however my black pcb can do 6-9-6 with 1.82v don't know where my screen shot is for that though lol

i don't remember but i saw someone post something about psc doing 6-9-6 with 1.72v and my goal is to find one
hoping the 7-9-7 2000mhz pi will do it or the gskill flare 7-9-7 2000mhz that will be comming in sometime this week also...

going to post results when i get home



i just noticed the spd! is that stock or was it flashed lol.. very nice find!

These are 1066 and 1333 value rams / honor belongs to a friend who found them ^^

P.S. Voltage was as said at 1,65v with the 1066s and 1,62 ca with the 1333

[korkutkaya]

Hey guys.

I am using G.SKILL PIS F3-17600CL7D-4GBPIS kit on my Sandy Bridge(Asus Maximus IV Extreme) mobo perfectly.
I am planning to upgrade my system to 8GB.So thinking about getting another kit of G.SKILL PIS F3-17600CL7D-4GBPIS.
However I have doubt 2xkits works at their specs on a SB mobo.Any idea?

Regard Korkut

[badatgames18]

i tried before with 4x2 2200cl7 (same pi in op)..
i couldn't get them to work, best i could do was cl8, but that was a while ago.. maybe with more tweaking it is possible. Higher vccio is probably going to be needed.. along with a few other things.

if you run 2T, it should be no problem.. (although you'll have a pretty big loss)

[korkutkaya]

i tried before with 4x2 2200cl7 (same pi in op)..
i couldn't get them to work, best i could do was cl8, but that was a while ago.. maybe with more tweaking it is possible. Higher vccio is probably going to be needed.. along with a few other things.

if you run 2T, it should be no problem.. (although you'll have a pretty big loss)

Thanks alot for your input.I will go for other Gskill models for Sandy Bridge systems. mems are too expensive
to take the risk.

[trans am]

I bought mine 2 years ago. its still the best 2x2gb ddr3 kit ive ever had. F317600CL7D-4GBPIS
mine are confirmed bbse 1st run 2200 7-10-10-28 pi kits. Ive run cas 6-9-6 to 2050 on crappy i3 imc days. all my highest submissions on hwbot were on this kit. I think I paid $179 at newegg at the time. they are priceless.

[hiwa]

they are still rox on all platforms, SB-E include.

[BeepBeep2]

I bought mine 2 years ago. its still the best 2x2gb ddr3 kit ive ever had. F317600CL7D-4GBPIS
mine are confirmed bbse 1st run 2200 7-10-10-28 pi kits. Ive run cas 6-9-6 to 2050 on crappy i3 imc days. all my highest submissions on hwbot were on this kit. I think I paid $179 at newegg at the time. they are priceless.

Problem with these kits though seems to be that they prefer tRCD = CL +3/4...

I can run 2050 6-10-6 24/7, 32M 2055 6-9-6 (1.75v)...

tRCD 10 is almost a must for me :/

[hiwa]

Problem with these kits though seems to be that they prefer tRCD = CL +3/4...

I can run 2050 6-10-6 24/7, 32M 2055 6-9-6 (1.75v)...

tRCD 10 is almost a must for me :/

with SB_E we have to set it +4 always with low latencies

[BeepBeep2]

with SB_E we have to set it +4 always with low latencies

Haha I know, maybe this kit does better CL latency at +4 compared to the kits that prefer +2/+3 and is therefore better for SB-E

For the former AMD AM3 platform, 7-9-7 flares were king for benching...up to 2200 7-9-7 in 32M. However I can do 2100 6-10-6 with this kit...7-9-7 is stuck at same 2050 as 6-9-6 ...32M was easy at 2150 7-10-7 though.