******Gigabyte GA-P67A-UD4 Discussion Thread******

[Leeghoofd]

But does it boot at 2400mhz Gaul ? Don't think so... so that ram divider is useless for normal SB...

[Gaul]

But does it boot at 2400mhz Gaul ? Don't think so... so that ram divider is useless for normal SB...

i'm sure it is, but did u'r DDR can touch 1200 mhz ?
we looking for 1200 CL 7/8/7/24 @ 1.65v ( MAX )

[Leeghoofd]

2 questions :

1) I wanna see a video now where your rig boots with the 2400mhz divider...
2) why do you start talking about 1200mhz ?

We bench at 2250mhz CL7-8-7, wtf is 1200Mhz CL7 ?

[dinos22]

LOL i'd love to see you get that divider working with your setup

[stasio]

Asus removed 2400 divider in latest BIOS's for all boards.
http://hardforum.com/showpost.php?p=...postcount=4278

[Gaul]

2 questions :

1) I wanna see a video now where your rig boots with the 2400mhz divider...
2) why do you start talking about 1200mhz ?

We bench at 2250mhz CL7-8-7, wtf is 1200Mhz CL7 ?

800 aka 1600
933 aka 1866
1066 aka 2133
1200 aka 2400

i think my Gskill F3-12800CL9D-4GBECO can't touch 2400
so i can't try div 2400

[Leeghoofd]

it worked with some early ES samples mate, doesn't work with current retails... it just doesn't post... We've got rams that could handle them frequencies ( with loose timings) it just doesn't post...

[Demo]

So I tried the bios today, multi step is there.. which level is probably the best to use?

I just need 1.380V at max load and no less than 1.000v at idle.. level4? or just turn off multi step and enabled standard LLC?

[stasio]

F6h is out.

[hersounds]

link & what's new stasio...thanks

[stasio]

In my sig.

[Andrea deluxe]

tryed

ok back to llc disabled and enabled.

more stable and great performance.

[dejanbinladen]

no levels or what ???

[Gaul]

sorry can't post anything coz had ASUS board now

[bluestang]

^^ then stay off this thread.

[Frost_Bite]

sorry can't post anything coz had ASUS board now

Definitely one of the most worthless comments in this thread...awesome job!

I just downloaded the new BIOS and will give it a try tomorrow morning. I don't see how it can be much more stable than F6F but if it gets me my final 100MHz then I'll be happy. I don't use the mult-level LLC options so they won't be missed by me. I'll post my results up once I get some time to play with it.

[ProStreetCamaro]

Question for you guys. I have the UD5 board but that thread has been stone cold dead for a while so I will ask here. I used to run 5.0 rock stable with my old NON B3 board. Once I received my B3 board I could no longer get 5.0 stable. Anybody else run into this issue or is my 2600K degrading?

Also what is with everybody switching to the Z68 boards? From my understanding the only thing over the P67 it offers is the use of the on chip gpu to do either video out or rendering. So I cant figure out what I am missing out on by not getting a Z68 board? Must be some reason everybody is switching to the Z68?

[stasio]

F6i is out.

[dejanbinladen]

F6i is out.

after few runs of 32M for gigabyte compettion my bclk doesnt respond any more, not for a 0,1mhz, i removed batery few times, cleared bios, and its the same, later i ll flash to older one, this one is bad

[dejanbinladen]

6 core ivy maybe, now i really wonder ....

http://www.pohrani.com/?8/2L/4qkWhz64/6core1155.jpg




F5 officialy supports 22nm ivy bridge

[stasio]

F6i is special Beta BIOS for GB Germany,they adjust some voltages,as per they request.

[hersounds]

F6F the american overclocker standar ...why more?

[stasio]

F6 is out.

[chucupis]

F6 is out.

What are the improvements of this bios compared with f5? this one has more than LLC enable/disable?

EDIT: Already testing it, it has llc until LVL 10, try to post some feedback vs f5

best regards from venezuela

[FL00D]

What are the improvements of this bios compared with f5? this one has more than LLC enable/disable?

EDIT: Already testing it, it has llc until LVL 10, try to post some feedback vs f5

best regards from venezuela

Cheers for the info mate. Keep us informed please. Ta.

Best,