Quote Originally Posted by rhia View Post
Hi guys, I'm looking for some help in getting my system stable.
I can load Win7 with no probs 21x215 at 1.4Vcore and 1.35uncore, but I get BSOD after 5-10mins of Prime95 (Errors 0x00000101 and 0x00000124).
I've upped the voltages up a bit, to 1.45Vcore and 1.4uncore, which I think is the highest safe for 24/7???, , temps are good 45idle and 66under load.
Here are my bios settings:
Code:
BIOS 0901
Target CPU Frequency 4.504MHz
Target DRAM Frequency 1715MHz

LN2 Mode [Disabled]***
QPI Loadline Calibration [Enabled]***

Sync Mode [Enabled]
AI Overclock Tuner [Manual]
OC From CPU level Up [Auto]
CPU Ratio Setting [21]
CPU Turbo Power Limit [Disabled]

>CPU Configuration----------------------------
CPU Ratio Setting [21]
C1E Support [Disabled]
Hardware Prefetcher [Enabled]
Adjacent Cache Line Prefetcher [Enabled]
Intel(R) Virtualiyation Tech [Enabled]
CPU TM Function [Enabled]
Execute Disable Bit [Enabled]
Intel(R) HT Technology [Disabled]
Active Processor Cores [All]
A20M []
Intel(R) SpeedStep(TM) Tech [Disabled]
Intel(R) C-STATE Tech [Disabled]
----------------------------------------------

BCLK Frequency [214]
PCIE Frequency [102]
DRAM Frequency [1715]
UCLK Frequency [3432]
QPI Link Data Rate [7723]

Memory Configuration Protect [Disabled]

>DRAM Timing Control--------------------------
CAS# Latency [8]
RAS# to CAS# Delay [8]
RAS# PRE Time [8]
RAS# ACT Time [24]
RAS# to RAS# Delay [Auto]
REF Cycle Time [Auto]
WRITE Recovery Time [Auto]
READ to PRE Time [Auto]
FOUR ACT WIN Time [Auto]
Back-To-BackCAS# Delay [Auto]

Timing Mode [1]
Round Trip Latency on CHA [Auto]
Round Trip Latency on CHB [Auto]
Round Trip Latency on CHC [Auto]

WRITE To READ Delay(DD) [Auto]
WRITE To READ Delay(DR) [Auto]
WRITE To READ Delay(SR) [Auto]
READ To WRITE Delay(DD) [Auto]
READ To WRITE Delay(DR) [Auto]
READ To WRITE Delay(SR) [Auto]
READ To READ Delay(DD) [Auto]
READ To READ Delay(DR) [Auto]
READ To READ Delay(SR) [Auto]
WRITE To WRITE Delay(DD) [Auto]
WRITE To WRITE Delay(DR) [Auto]
WRITE To WRITE Delay(SR) [Auto]
----------------------------------------------

CPU Differential Amplitude [Auto]
CPU Clock Skew [Auto]
IOH Clock Skew [Auto]
------------ Extreme Engine Digi+ ------------
Digi+ PWR Mode [X-Power]
PWR Volt. Control [Auto]
Load-Line Calibration [50%]
CPU Voltege OCP [Enabled]
CPU PWM Frequency [Auto]

Extreme OV [Disabled]
Extreme OC [Auto]

CPU Voltage [1.45]
CPU PLL Voltage [1.81]
QPI/DRAM Core Voltage [1.4]
DRAM Bus Voltage [1.65]

>DRAM REF Voltages----------------------------
DRAM DATA REF Voltage on CHA []
DRAM CTRL REF Voltage on CHA []
DRAM DATA REF Voltage on CHB []
DRAM CTRL REF Voltage on CHB []
DRAM DATA REF Voltage on CHC []
DRAM CTRL REF Voltage on CHC []
----------------------------------------------

IOH Voltage [1.23]
IOH PCIE Voltage [1.5]

ICH Voltage [1.1]
ICH PCIE Voltage [Auto]

---------- Spread Spectrum Control -----------
CPU Spread Spectrum [Disabled]
DRAM Spread Spectrum [Disabled]
Any help would be greatly appreciated
Too low vCore, IMO. VTT is probably more then enough for that UnCore speed, but it's not easy to run CPU @ 4.5GHz.

Quote Originally Posted by angel_dust View Post
What do you all think of BIOS 1005 so far?? Are they more stable than the previous releases and dose everything still function as it should?
Good. Probably best of both paths of development 100x and 00xx. 0011 and 1004 shared same BIOS template, so you could cross-load settings into each other. 1005 could be merger of two.