** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[radaja]

andre I still can figure out how to "take a pic" of the bios like you guys have and posted it. I know once you get a screen shoot you can upload it to imageshack and post it . Anyway I changed my settings to mirror Jsquire and it booted fine up to 425FSB. I tried 450 and it wouldn't get past the windows load screen I'm thinking this chip needs more than 1.4Vcore? What do think?

if you mean the bios template scrollbox then this will help you.
just copy and paste and heres how to put it into a scroll box.

first at the bottom of the page where the reply box is,hit the go advance button.
then when your in the advance reply page,up on top of the reply box you can see
the button that looks like this #,click it and you will now see in the reply box this appear.
[code][code]
paste your template between the two [code] boxes and the template will now be inside
a scroll box when you post it.

but if you mean actual pics of you bios screen then you need to upload the pics like you did
and then post the link address to the piscs.

[systemviper]

andre I still can figure out how to "take a pic" of the bios like you guys have and posted it. I know once you get a screen shoot you can upload it to imageshack and post it . Anyway I changed my settings to mirror Jsquire and it booted fine up to 425FSB. I tried 450 and it wouldn't get past the windows load screen I'm thinking this chip needs more than 1.4Vcore? What do think?

usually a load screen bsod is more Vcore.....

[bignick]

First I get how to post the bios once it's in my pics folder. And I also get how to upload it and post on the thread what I don't get is how to "copy" or "take a pic" and move it into a folder so I can do those things. It might be the most simple step but I just can't get that part. Never done a screen shot of the bios before. But anyway I had to increase Vcore up to 1.5V in the bios to make it stable at 450Mhz and that was to much, I couldn't keep the temps down. It runs 75-76C at 100% load so I guess I'm looking for a new processor now I was hoping to get at least 500Mhz and the chip might do it but not on air.... I'm gonna look for a E8600. Thanks guys

[bignick]

Whats the Vcore droop on these boards anyone measure it yet? And if it's like what the other gigabyte boards are is there a mod? Also what program do you use to measure Vdroop?

[andressergio]

First I get how to post the bios once it's in my pics folder. And I also get how to upload it and post on the thread what I don't get is how to "copy" or "take a pic" and move it into a folder so I can do those things. It might be the most simple step but I just can't get that part. Never done a screen shot of the bios before. But anyway I had to increase Vcore up to 1.5V in the bios to make it stable at 450Mhz and that was to much, I couldn't keep the temps down. It runs 75-76C at 100% load so I guess I'm looking for a new processor now I was hoping to get at least 500Mhz and the chip might do it but not on air.... I'm gonna look for a E8600. Thanks guys

you can just take a pic of your bios settings mate and up it here
http://imageshack.us/

or just use one of the templates posted and edit it and re post

Whats the Vcore droop on these boads anyone measure it yet? And if it's like what I think it is is there a mod? Also what program do you use to measure Vdroop?

no need to mod anything mate just enable LLC

cheers
Sergio

[kagula323]

First I get how to post the bios once it's in my pics folder. And I also get how to upload it and post on the thread what I don't get is how to "copy" or "take a pic" and move it into a folder so I can do those things. It might be the most simple step but I just can't get that part. Never done a screen shot of the bios before. But anyway I had to increase Vcore up to 1.5V in the bios to make it stable at 450Mhz and that was to much, I couldn't keep the temps down. It runs 75-76C at 100% load so I guess I'm looking for a new processor now I was hoping to get at least 500Mhz and the chip might do it but not on air.... I'm gonna look for a E8600. Thanks guys

you must use a foto camera for actually taking a pic of bios settings screen ... and then download it to your pc and post it to imageshack

[Dark-Energy]

Been a while since I've updated in this whole thread I gotta catch up; been busy with things lately. I'll try to get on MSN sometime Sergio and go Uruguay!

To update my board doesn't seem to like frequency latch of 400 and I figured this out after some games were crashing. I ran prime custom 8k and it passed, however blend failed after a few seconds and I even got a BSOD a few times . It wasn't responding to any bios settings so I changed it to 333 latch and it seems to be fine and stable, it passed both blend and custom 8k now, and no more crashing or nasty BSOD Although, my ram latency shot up 20ns and read times went down, I think this is typical but will it really affect performance in games?

I raised vcore up a tiny bit after Sergio helped me as I was getting BSODs again and I thought I fixed it by doing this; but I guess murphy's law is right. I am running LLC at 1.43125 in bios and I'm pretty sure this is borderline safe for 24/7 as I've been running this for a few weeks but didn't notice instability cause I was just browsing the web for most of that time. I'll try lowering it tommorow and I'm pretty sure it will be fine. Temps are too high for my liking in Prime 8k, it hits 70C and I want to stay under 65C, and this was after reseating with IC7 compound and attaching 2 Gentle Typhoons to the rad in push/pull. Couldn't imagine what temps would have been before

[andressergio]

Been a while since I've updated in this whole thread I gotta catch up; been busy with things lately. I'll try to get on MSN sometime Sergio and go Uruguay!

To update my board doesn't seem to like frequency latch of 400 and I figured this out after some games were crashing. I ran prime custom 8k and it passed, however blend failed after a few seconds and I even got a BSOD a few times . It wasn't responding to any bios settings so I changed it to 333 latch and it seems to be fine and stable, it passed both blend and custom 8k now, and no more crashing or nasty BSOD Although, my ram latency shot up 20ns and read times went down, I think this is typical but will it really affect performance in games?

I raised vcore up a tiny bit after Sergio helped me as I was getting BSODs again and I thought I fixed it by doing this; but I guess murphy's law is right. I am running LLC at 1.43125 in bios and I'm pretty sure this is borderline safe for 24/7 as I've been running this for a few weeks but didn't notice instability cause I was just browsing the web for most of that time. I'll try lowering it tommorow and I'm pretty sure it will be fine. Temps are too high for my liking in Prime 8k, it hits 70C and I want to stay under 65C, and this was after reseating with IC7 compound and attaching 2 Gentle Typhoons to the rad in push/pull. Couldn't imagine what temps would have been before

Hey mate how are you ? true a long time

Thanks mate tomorrow we go against my friends of Holland

Nice you figured out settings and temps, keep posting and im on msn all day online

Cheers
Sergio

[andressergio]

you must use a foto camera for actually taking a pic of bios settings screen ... and then download it to your pc and post it to imageshack

kagula how are your tests going ?

[andressergio]

usually a load screen bsod is more Vcore.....

hey System any update ? did u get that QX ?

[OC Nub]

Finally got my camera back Sergio, this was the new loop I built, currently taking things apart to switch mobo's so its even more of a mess than normal. The bottom cap to the new res has a leak to I turned it upside, works fine now though.



Uploaded with ImageShack.us

[NoGuru]

I like the sideways mounted RAD.

[OC Nub]

Thanks, it lines up perfect with the vents on my window ac.

[andressergio]

Finally got my camera back Sergio, this was the new loop I built, currently taking things apart to switch mobo's so its even more of a mess than normal. The bottom cap to the new res has a leak to I turned it upside, works fine now though.



Uploaded with ImageShack.us

wow thats a nice setup Tom want more pics i think you need the HX850 will make your cabling much easier

[andressergio]

Thanks, it lines up perfect with the vents on my window ac.

u say it AC sticked to the rad i guess 1mm da perfect cooling machine

[OC Nub]

Thanks Sergio, the cables are a pita but I am use to it.

[andressergio]

Thanks Sergio, the cables are a pita but I am use to it.

you where right i like the white tubing

[In-Fluence]

Hi all,

Just to let you know that I'm selling all my P45 boards (UD3P, USB3P and MIIF), GSkill PI 9600's and 1296MHz+ capable OCZ reapers.

Details in this thread - further details on my Ebay account

Hopefully any of these in the right hands are bound to go far - all the best

[kagula323]

kagula how are your tests going ?

hi sergio ... I'm currently searchin' for a P55 mobo to have fun with a good i5 650 I have and joining radaja in the core i3 thread ... and nice results ... nice memory u got there

[MrDucky]

So whats your ebay account then i cant find it...

[andressergio]

hi sergio ... I'm currently searchin' for a P55 mobo to have fun with a good i5 650 I have and joining radaja in the core i3 thread ... and nice results ... nice memory u got there

nice man that will be awesome P55 is fast for mem, get the STALENTS and you will see

[radaja]

you where right i like the white tubing

yep that white tubing looks awesome.i like the look of 1/2 ID 3/4 OD and the white just makes it look even thicker.i have the blue and now im using black
and the black is so slimming that i have lost the thick tube look

Hi all,

Just to let you know that I'm selling all my P45 boards (UD3P, USB3P and MIIF), GSkill PI 9600's and 1296MHz+ capable OCZ reapers.

Details in this thread - further details on my Ebay account

Hopefully any of these in the right hands are bound to go far - all the best

if you absolutely dont have to sell all your p45's i would seriously
reconsider keeping the EP45-UD3P because eventually you will yearn to play
with it again.and by then you wont be able to find one.hell sell the MaxII and
one gigabyte and keep the other.i would keep the UD3P and the 9600's:d

[In-Fluence]

Yeah, I know what your getting at - the UD3P has been a lot of fun, but I've spent so long procrastinating and not actually using my machine I feel I need to move on the best way I can. Plus I really need the money to clear debts as I could be out of a job in a few months!
I'm happy with my i7 920 (and new pump & res), and the power it provides is all I'm going to need for a fair while.

To all potential buyers - I'm on ebay UK - go to advanced search - by seller- name 'in-fluence'.

Please note there's NO reserve on the items either, although you can buy them for the prices listed in the for sale section - I'm open to offers too!

[kagula323]

nice man that will be awesome P55 is fast for mem, get the STALENTS and you will see

yes ... was thinkin' about them ... hope when my friend will go to states next time he will be able to get them for me ... I live in Roumania, Europe, so it's kind of hard for me to get good parts at good prices

[andressergio]

yes ... was thinkin' about them ... hope when my friend will go to states next time he will be able to get them for me ... I live in Roumania, Europe, so it's kind of hard for me to get good parts at good prices

ja tell that to me

good luck mate hope you get a nice set