** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

[zsamz_]

Enjoy the best DDR2 on earth T !!! the fan looks awesome for them

1300 was easy on my old set
i'm full blown into ddr3 now
radaja got me a set of the supertalent to play with
hypers like d9 now

[radaja]

thats just what you thinkthey my precious now

[the_real_7]

ya i heard about those supertalent I gotta see Everest latency on those i see they do some tight ddr 3 timings be great also on a p55

[zsamz_]

thats just what you thinkthey my precious now

np bud
dang your 980x is shipped
and in the usa as we speak

ya i heard about those supertalent I gotta see Everest latency on those i see they do some tight ddr 3 timings be great also on a p55

i had crap hypers on evga p55 and was good ti'll they dies
even did 2k cas7
the death was peacefull cause i got refunded
good hypers is somethin else

[andressergio]

i had crap hypers on evga p55 and was good ti'll they dies
even did 2k cas7
the death was peacefull cause i got refunded
good hypers is somethin else

aint 2200 CL8 Stalents good hypers ? the newer chips that GT's uses ?

[andressergio]

Guys

I want to watercool my MCH is worth it ? i cant find a block for the USB3P other than the MCW30

any help will be apreciated

[Jor3lBR]

Guys

I want to watercool my MCH is worth it ? i cant find a block for the USB3P other than the MCW30

any help will be apreciated

Hey Sergio, people had success with this block here:

EK-NB/SB 5 http://www.performance-pcs.com/catal...ducts_id=23638

[zsamz_]

aint 2200 CL8 Stalents good hypers ? the newer chips that GT's uses ?

after seein radaja's results .....
i think they all the same chips
n people payin more for the 2200 and 2000 cas7
gtx2 is binned just to make sure no crap chips pass and for speed
i rather have a set that can do 1800+ cas6 than 2200 cas7
if i can have 1600 cas5 24/7 i be in heaven
my best hypers do 1740z cas 6 and with 1.65v i was testing for more but my bios was corrupting
and i just bought an evga 3xsli just in case the rexIII goes belly up lol
when i get time i gonna test some more this time 1.7v

[andressergio]

Hey Sergio, people had success with this block here:

EK-NB/SB 5 http://www.performance-pcs.com/catal...ducts_id=23638

thanks mate

[Rebound]

Radaja,

i am running on a q9550 C1 1.25 vid

[andressergio]

after seein radaja's results .....
i think they all the same chips
n people payin more for the 2200 and 2000 cas7
gtx2 is binned just to make sure no crap chips pass and for speed
i rather have a set that can do 1800+ cas6 than 2200 cas7
if i can have 1600 cas5 24/7 i be in heaven
my best hypers do 1740z cas 6 and with 1.65v i was testing for more but my bios was corrupting
and i just bought an evga 3xsli just in case the rexIII goes belly up lol
when i get time i gonna test some more this time 1.7v

ya i bought the 2200 CL8 lets hope i got a good one

[the_real_7]

After me and Sergio been working all day to get somewhere with this ram being it's a little picky with this board, becuase it a version 1.1. But after some tinkering and putting the ram settings at stock and putting the Drive Strength Profile to oc - 1200 the board stabled out and did a 8k 8k in prime and actually started to work fine with the 240B divider .. timings are loose as hell at moment...... but will work on more tomorrow , any one else have a 1.1 v

 [code]******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Standard ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.5    ]
CPU Frequency 4.5GHz............................[ 500 x 8.5]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 500      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 900mv   ]
PCI Express Clock Drive.........................[ 900mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 50ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
Extreme Memory Profile (X.M.P)..................[ Profile1 ]
(G) MCH Frequency Latch.........................[ 333      ]
System Memory Multipler.........................[ 2.40B    ]
Memory Frequency 1066...........................[ 1200     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ 4       ]
tWTR[4].........................................[ 4       ]
tWR[13].........................................[ 13      ]
tRFC[68] .......................................[ 50      ] 
tRTP[4].........................................[ 4       ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 9       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ auto       ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ auto       ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ auto       ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto       ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ oc-1200 ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ auto    ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ auto    ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ oc -1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.1875  ]...................[ 1.4250  ]
CPU Termination   [ 1.20    ]...................[ 1.300   ]
CPU PLL           [ 1.50    ]...................[ 1.570   ]
CPU Reference     [ 0.760   ]...................[ 0.886   ] 
 
MCH Core          [ 1.100   ]...................[ 1.460   ] 
MCH Reference     [ 0.760   ]...................[ 0.901   ]
MCH/DRAM Refernce [ 0.900   ]...................[ Auto    ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.200   ] 
 
DRAM Voltage      [ 1.800   ]...................[ 2.200   ] 
DRAM Termination  [ 0.900   ]...................[ Auto    ]
Channel A Ref     [ 0.900   ]...................[ Auto    ]
Channel B Ref     [ 0.900   ]...................[ Auto    ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ][/code] 

[andressergio]

After me and Sergio been working all day to get somewhere with this ram being it's a little picky with this board, becuase it a version 1.1. But after some tinkering and putting the ram settings at stock and putting the Drive Strength Profile to oc - 1200 the board stabled out and did a 8k 8k in prime and actually started to work fine with the 240B divider .. timings are loose as hell at moment...... but will work on more tomorrow , any one else have a 1.1 v

 [code]******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Standard ]
CPU Clock Ratio.................................[ 8        ]
Fine CPU Clock Ratio............................[ + 0.5    ]
CPU Frequency 4.5GHz............................[ 500 x 8.5]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 500      ]
PCI Express Frequency (Mhz).....................[ 100      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 900mv   ]
PCI Express Clock Drive.........................[ 900mv   ]
CPU Clock Skew..................................[ 0ps     ]
MCH Clock Skew..................................[ 50ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
Extreme Memory Profile (X.M.P)..................[ Profile1 ]
(G) MCH Frequency Latch.........................[ 333      ]
System Memory Multipler.........................[ 2.40B    ]
Memory Frequency 1066...........................[ 1200     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 5       ]
tRCD............................................[ 5       ]
tRP.............................................[ 5       ]
tRAS............................................[ 15      ]
 
******Advanced Timing Control******
 
tRRD[4].........................................[ 4       ]
tWTR[4].........................................[ 4       ]
tWR[13].........................................[ 13      ]
tRFC[68] .......................................[ 50      ] 
tRTP[4].........................................[ 4       ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 9       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ auto       ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ auto       ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ auto       ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto       ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ oc-1200 ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 9 ] ................[ 8       ]
tRD Phase0 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ] ................[ auto    ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ auto    ]
tWR 2rd (Differnt Rank)   [ 7 ] ................[ auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ oc -1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.1875  ]...................[ 1.4250  ]
CPU Termination   [ 1.20    ]...................[ 1.300   ]
CPU PLL           [ 1.50    ]...................[ 1.570   ]
CPU Reference     [ 0.760   ]...................[ 0.886   ] 
 
MCH Core          [ 1.100   ]...................[ 1.460   ] 
MCH Reference     [ 0.760   ]...................[ 0.901   ]
MCH/DRAM Refernce [ 0.900   ]...................[ Auto    ]
ICH I/O           [ 1.500   ]...................[ 1.500   ]
ICH Core          [ 1.100   ]...................[ 1.200   ] 
 
DRAM Voltage      [ 1.800   ]...................[ 2.200   ] 
DRAM Termination  [ 0.900   ]...................[ Auto    ]
Channel A Ref     [ 0.900   ]...................[ Auto    ]
Channel B Ref     [ 0.900   ]...................[ Auto    ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ][/code] 

Great my friend rev 1.1 is picky on dividers maybe someone who has it can enlight us

[Dark-Energy]

Wow, that's really close to the same bios settings I am using for the same clock. Only difference is you have a Q9650, and faster ram.

[bluestang]

Dualies and Skews...what's recommended for 8x 500-525 FSB for an E8500? It seems critical for Quads, but what about Duals? Thanks!

[andressergio]

Dualies and Skews...what's recommended for 8x 500-525 FSB for an E8500? It seems critical for Quads, but what about Duals? Thanks!

same Blue give those i posted a try

[the_real_7]

Wow, that's really close to the same bios settings I am using for the same clock. Only difference is you have a Q9650, and faster ram.

Hey Dark-Energy so far im stable but it is believed there is a problem with with our 1.1 boards im not saying its not ... but im willing to go farther and say just a difference in settings due to the revisions , please send me your temp plate and a Everest if possible

[bluestang]

same Blue give those i posted a try

Thanks Sergio, 900/900/0/50 I'll try this weekend as I'm hoping to get 8x 500-525 FSB stable on my E8500 with some nice DDR3 RAM speeds also. Will post screenies if, I mean when, I get there.

[systemviper]

5215.58 mhz systemviper Intel Xeon X3380 @5215.6MHz


http://valid.canardpc.com/show_oc.php?id=1236548

[radaja]

X3380
I got some new, well old ddr2 coming from a friend that is killer, I will be posting some results with my x3380 and ud3p over the next few days.

very nice systemviper,you werent kidding when you said you were going
to posp some results with your X3380 in the next few dayssimply amazing results

[l0ud_sil3nc3]

5215.58 mhz systemviper Intel Xeon X3380 @5215.6MHz


http://valid.canardpc.com/show_oc.php?id=1236548

very nice I have been waiting to see a screen shot

[NoGuru]

5215.58 mhz systemviper Intel Xeon X3380 @5215.6MHz


http://valid.canardpc.com/show_oc.php?id=1236548

Nice work SV!

[OC Nub]

After me and Sergio been working all day to get somewhere with this ram being it's a little picky with this board, becuase it a version 1.1. But after some tinkering and putting the ram settings at stock and putting the Drive Strength Profile to oc - 1200 the board stabled out and did a 8k 8k in prime and actually started to work fine with the 240B divider .. timings are loose as hell at moment...... but will work on more tomorrow , any one else have a 1.1 v

Nice work.

I have a rev1.1, it hated 240b. I had to use 250a with the gskill pi's to reach 1200. Finally I gave up and went back to the rev1.0.

[andressergio]

5215.58 mhz systemviper Intel Xeon X3380 @5215.6MHz


http://valid.canardpc.com/show_oc.php?id=1236548

great viper almost close to my 5254

[systemviper]

great viper almost close to my 5254

5254 that is a nice score...

I don't see you on hwbot? i do see Jor3llBR/Elano

@ 5255 mhz in the top spot,

mine is #2 for the silver....

that is my next goal....
going for over 5255 mhz

I almost had it but cpuz froze at 561fsb/ and it was dinner time....
i think i just need to adjust a bit,,, got it up to 549 and need to get
over 553

more to come. then i will go for the lower clock 2D stuff and start playing
with the ram,...