** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

**dustin_ds3000** · 05-21-2010, 02:16 PM

I need help getting my E8500 to 4.275ghz, my EP45-UD3R is using the F12 BIOS

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9
Fine CPU Clock Ratio...................:.0.5
CPU Frequency .........................: 4.275GHz (450*9.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 450
PCI Express Frequency (Mhz) ...........: 100

C.I.A.2 .................................:[Disabled]


CPU Clock Drive........................: 800
PCI Express Clock Drive................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)....................: 0


DRAM Performance Control
Performance Enhance....................: [Extreme]
Extreme Memory Profile (X.M.P.)........: Profile 2
(G)MCH Frequency Latch.................: AUTO
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ................: 900
DRAM Timing Selectable ................: [Auto]

Motherboard Voltage Control
Voltage Type.………... Manual
LLC....................................: [Enabled]
CPU Vcore….……….........................: 1.38125v
CPU Termination….......................: 1.28v
CPU PLL………………….........................: 1.5v
CPU Referen.………….......................: 0.795v
MCH/ICH
MCH Core…………….....1.100V...............: 1.36v
MCH Reference….…….0.800V...............: 0.790
MCH/DRAM Ref.…......0.900V.............: Normal
ICH I/O……………….....1.500V...............: Normal
ICH Core…………...……1.100V................: Normal

DRAM
DRAM Voltage ……....1.800V..............: 2.000V
DRAM Termination .…0.900V..............: Normal
Channel A Reference 0.900V.............: Normal
Channel B Reference 0.900V.............: Normal

i can run prime95 for about 10 minuets until one core stops, and the highest CPU core temp is 63c

**andressergio** · 05-21-2010, 03:14 PM

Originally Posted by dustin_ds3000

I need help getting my E8500 to 4.275ghz, my EP45-UD3R is using the F12 BIOS

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9
Fine CPU Clock Ratio...................:.0.5
CPU Frequency .........................: 4.275GHz (450*9.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 450
PCI Express Frequency (Mhz) ...........: 100

C.I.A.2 .................................:[Disabled]


CPU Clock Drive........................: 800
PCI Express Clock Drive................: 900
CPU Clock Skew (ps)....................: 50
MCH Clock Skew (ps)....................: 0


DRAM Performance Control
Performance Enhance....................: [Extreme]
Extreme Memory Profile (X.M.P.)........: Profile 2
(G)MCH Frequency Latch.................: AUTO
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ................: 900
DRAM Timing Selectable ................: [Auto]

Motherboard Voltage Control
Voltage Type.………... Manual
LLC....................................: [Enabled]
CPU Vcore….……….........................: 1.38125v
CPU Termination….......................: 1.28v
CPU PLL………………….........................: 1.5v
CPU Referen.………….......................: 0.795v
MCH/ICH
MCH Core…………….....1.100V...............: 1.36v
MCH Reference….…….0.800V...............: 0.790
MCH/DRAM Ref.…......0.900V.............: Normal
ICH I/O……………….....1.500V...............: Normal
ICH Core…………...……1.100V................: Normal

DRAM
DRAM Voltage ……....1.800V..............: 2.000V
DRAM Termination .…0.900V..............: Normal
Channel A Reference 0.900V.............: Normal
Channel B Reference 0.900V.............: Normal

i can run prime95 for about 10 minuets until one core stops, and the highest CPU core temp is 63c

put turbo not extreme and profile1 mate

900/900/0/50

PCIE= 101

for 1,2vtt set .785CPU ref and .80MCH then up vtt to ya current value

try

Cheers

Sergio

**dustin_ds3000** · 05-21-2010, 03:27 PM

Originally Posted by andressergio

put turbo not extreme and profile1 mate

900/900/0/50

PCIE= 101

for 1,2vtt set .785CPU ref and .80MCH then up vtt to ya current value

try

Cheers

Sergio

in the BIOS for Extreme Memory Profile i have Auto, profile2, and disable. No profile1 unless disable is profile1

*10 minutes later*

Those BIOS settings give the the blue screen after windows starts to load

*10 minutes later*

i changed the MCH ref to .760 and i booted into windows and im running prime95 now

**andressergio** · 05-21-2010, 04:40 PM

Originally Posted by radaja

NoGuru,very nice WCing build.looks like andressergios and yours and mine are family.
all gigabyte,all blue and all look great.

a giga family

Cheers Rob

Sergio

**dustin_ds3000** · 05-21-2010, 05:00 PM

well pime95 failed after a few minutes so i started to try other settings, after getting blue screen after blue screen i just went back to my 9.5x422 4Ghz settings.

**andressergio** · 05-21-2010, 05:15 PM

Originally Posted by dustin_ds3000

well pime95 failed after a few minutes so i started to try other settings, after getting blue screen after blue screen i just went back to my 9.5x422 4Ghz settings.

did u use my settings mate ?

remember that you have to set .785 CPU REF and .80 MCH and put VTT 1.2 then up just VTT to the value you want letting other change alone

you have to try skews

800/800/0/50
900/900/0/50
800/900/50/100

seek wich fits best for ya

MCH on 1,4 if you are pushing

vdimm a bit overvolted

and NO extreme , just use STANDARD to try then you have time to put TURBO

try CUSTOM BLEND 8k to 8k at first if it passes that
go blend all. if fails...notch vcore

Cheers hope it helps

**NoGuru** · 05-21-2010, 06:24 PM

Fan controller is installed.

**Hoss331** · 05-21-2010, 06:33 PM

Originally Posted by dustin_ds3000

I need help getting my E8500 to 4.275ghz, my EP45-UD3R is using the F12 BIOS

i can run prime95 for about 10 minuets until one core stops, and the highest CPU core temp is 63c

Give this a try.

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9
Fine CPU Clock Ratio...................:.0.5
CPU Frequency .........................: 4.275GHz (450*9.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 450
PCI Express Frequency (Mhz) ...........: 100

C.I.A.2 .................................:[Disabled]


CPU Clock Drive........................: 800
PCI Express Clock Drive................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)....................: 0


DRAM Performance Control
Performance Enhance....................: Standard
Extreme Memory Profile (X.M.P.)........: disabled
(G)MCH Frequency Latch.................: 400
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ................: 900
DRAM Timing Selectable ................: [Auto]

Motherboard Voltage Control
Voltage Type.………... Manual
LLC....................................: [Enabled]
CPU Vcore….……….........................: 1.38125v
CPU Termination….......................: 1.26v
CPU PLL………………….........................: 1.50v
CPU Referen.………….......................: 0.798v
MCH/ICH
MCH Core…………….....1.100V...............: 1.32v
MCH Reference….…….0.800V...............: 0.718 - 0.758
MCH/DRAM Ref.…......0.900V.............: Auto
ICH I/O……………….....1.500V...............: 1.500
ICH Core…………...……1.100V................: 1.100

DRAM
DRAM Voltage ……....1.800V..............: 2.000V
DRAM Termination .…0.900V..............: Auto
Channel A Reference 0.900V.............: Auto
Channel B Reference 0.900V.............: Auto

Originally Posted by NoGuru

Fan controller is installed.

Looking good

**systemviper** · 05-21-2010, 06:50 PM

Hi Hoss, great stuff with the uD3P,

I would love to see your template for the Q9650

in the high 4.8+ ghz to 5ghz/////

any chance of that?

best regards/steve

Originally Posted by Hoss331

Give this a try.

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio .......................: 9
Fine CPU Clock Ratio...................:.0.5
CPU Frequency .........................: 4.275GHz (450*9.5)


Clock Chip Control
Standard Clock Control
CPU Host Clock Control.................: [Enabled]
CPU Host Frequency (Mhz) ..............: 450
PCI Express Frequency (Mhz) ...........: 100

C.I.A.2 .................................:[Disabled]


CPU Clock Drive........................: 800
PCI Express Clock Drive................: 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)....................: 0


DRAM Performance Control
Performance Enhance....................: Standard
Extreme Memory Profile (X.M.P.)........: disabled
(G)MCH Frequency Latch.................: 400
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ................: 900
DRAM Timing Selectable ................: [Auto]

Motherboard Voltage Control
Voltage Type.………... Manual
LLC....................................: [Enabled]
CPU Vcore….……….........................: 1.38125v
CPU Termination….......................: 1.26v
CPU PLL………………….........................: 1.50v
CPU Referen.………….......................: 0.798v
MCH/ICH
MCH Core…………….....1.100V...............: 1.32v
MCH Reference….…….0.800V...............: 0.718 - 0.758
MCH/DRAM Ref.…......0.900V.............: Auto
ICH I/O……………….....1.500V...............: 1.500
ICH Core…………...……1.100V................: 1.100

DRAM
DRAM Voltage ……....1.800V..............: 2.000V
DRAM Termination .…0.900V..............: Auto
Channel A Reference 0.900V.............: Auto
Channel B Reference 0.900V.............: Auto

Looking good

**NeoGeo333** · 05-21-2010, 07:11 PM

this is very frustrating o/c in hot summer days is a pita. Just got a new USB3P and man the idle temp for my q6600 is 58-60'C. Even with a/c on is like 53-55'C. Seeing how you guys clock above 3.8ghz is crazy.

**NoGuru** · 05-21-2010, 07:40 PM

Originally Posted by NeoGeo333

this is very frustrating o/c in hot summer days is a pita. Just got a new USB3P and man the idle temp for my q6600 is 58-60'C. Even with a/c on is like 53-55'C. Seeing how you guys clock above 3.8ghz is crazy.

That can't be right, idle 60C

Remount you cooler. Make sure the fan is working.

**Hoss331** · 05-21-2010, 07:55 PM

Originally Posted by systemviper

Hi Hoss, great stuff with the uD3P,

I would love to see your template for the Q9650

in the high 4.8+ ghz to 5ghz/////

any chance of that?

best regards/steve

Thanks, Im not good at keeping track of old settings but this should be pretty close for the 5.0 spi 1m and 4.95 wprime 1024 water runs.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.95GHz...........................[ 550 x 9.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 550      ]
PCI Express Frequency (Mhz).....................[ 101      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv   ]
PCI Express Clock Drive.........................[ 1000mv   ]
CPU Clock Skew..................................[ 100ps    ]
MCH Clock Skew..................................[ 50ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400      ]
System Memory Multipler.........................[ 2.00D    ]
Memory Frequency 1066...........................[ 1100     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 4       ]
tRCD............................................[ 4       ]
tRP.............................................[ 4       ]
tRAS............................................[ 10      ]
 
******Advanced Timing Control******
 
tRRD[3].........................................[ 3       ]
tWTR[3].........................................[ 3       ]
tWR[6]..........................................[ 6       ]
tRFC[54]........................................[ 34      ]
tRTP[3].........................................[ 3       ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 8       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]

tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 8       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15  ].....................[ 1.600   ]
CPU Termination   [ 1.20  ].....................[ 1.520   ]
CPU PLL           [ 1.50  ].....................[ 1.670   ]
CPU Reference     [ 0.760 ].....................[ 1.003   ]
 
MCH Core          [ 1.100 ].....................[ 1.560   ]
MCH Reference     [ 0.760 ].....................[ 0.963   ]
MCH/DRAM Refernce [ 0.900 ].....................[ 1.230   ]
ICH I/O           [ 1.500 ].....................[ 1.500   ]
ICH Core          [ 1.100 ].....................[ 1.100   ]
 
DRAM Voltage      [ 1.800 ].....................[ 2.460   ]
DRAM Termination  [ 0.900 ].....................[ 1.230   ]
Channel A Ref     [ 0.900 ].....................[ 1.230   ]
Channel B Ref     [ 0.900 ].....................[ 1.230   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

These are my current boot settings for 5.1+ and so far are good for spi 1m up to 5.13(570).

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 5.1GHz............................[ 567 x 9.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 567      ]
PCI Express Frequency (Mhz).....................[ 101      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv   ]
PCI Express Clock Drive.........................[ 1000mv   ]
CPU Clock Skew..................................[ 100ps    ]
MCH Clock Skew..................................[ 100ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 333      ]
System Memory Multipler.........................[ 2.00B    ]
Memory Frequency 1066...........................[ 1134     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 4       ]
tRCD............................................[ 4       ]
tRP.............................................[ 4       ]
tRAS............................................[ 8       ]
 
******Advanced Timing Control******
 
tRRD[3].........................................[ 4       ]
tWTR[3].........................................[ 4       ]
tWR[6]..........................................[ 8       ]
tRFC[54]........................................[ 26      ]
tRTP[3].........................................[ 4       ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 9       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]

tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 9       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15  ].....................[ 1.640   ]
CPU Termination   [ 1.20  ].....................[ 1.600   ]
CPU PLL           [ 1.50  ].....................[ 1.710   ]
CPU Reference     [ 0.760 ].....................[ 1.038   ]
 
MCH Core          [ 1.100 ].....................[ 1.600   ]
MCH Reference     [ 0.760 ].....................[ 1.013   ]
MCH/DRAM Refernce [ 0.900 ].....................[ 1.270   ]
ICH I/O           [ 1.500 ].....................[ 1.570   ]
ICH Core          [ 1.100 ].....................[ 1.200   ]
 
DRAM Voltage      [ 1.800 ].....................[ 2.540   ]
DRAM Termination  [ 0.900 ].....................[ 1.270   ]
Channel A Ref     [ 0.900 ].....................[ 1.270   ]
Channel B Ref     [ 0.900 ].....................[ 1.270   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

**NeoGeo333** · 05-21-2010, 08:52 PM

Originally Posted by NoGuru

That can't be right, idle 60C

Remount you cooler. Make sure the fan is working.

opened the case and notice way too many micro bubbles in the loop. anyone with advice to take care of that?

**NoGuru** · 05-21-2010, 09:13 PM

Originally Posted by NeoGeo333

opened the case and notice way too many micro bubbles in the loop. anyone with advice to take care of that?

To get the bubbles out you need to shake the case a bit and open the res and bleed them.
I don't think the is your problem though. I would remount the cooler.

**systemviper** · 05-21-2010, 09:16 PM

Thanks mucho Hoss, i was very interested in the skews and a few subtle settings.

I'll give them a shot tomorrow.

best regards/steve

Originally Posted by Hoss331

Thanks, Im not good at keeping track of old settings but this should be pretty close for the 5.0 spi 1m and 4.95 wprime 1024 water runs.

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio...............................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 4.95GHz...........................[ 550 x 9.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 550      ]
PCI Express Frequency (Mhz).....................[ 101      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv   ]
PCI Express Clock Drive.........................[ 1000mv   ]
CPU Clock Skew..................................[ 100ps    ]
MCH Clock Skew..................................[ 50ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 400      ]
System Memory Multipler.........................[ 2.00D    ]
Memory Frequency 1066...........................[ 1100     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 4       ]
tRCD............................................[ 4       ]
tRP.............................................[ 4       ]
tRAS............................................[ 10      ]
 
******Advanced Timing Control******
 
tRRD[3].........................................[ 3       ]
tWTR[3].........................................[ 3       ]
tWR[6]..........................................[ 6       ]
tRFC[54]........................................[ 34      ]
tRTP[3].........................................[ 3       ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 8       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]

tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 8       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15  ].....................[ 1.600   ]
CPU Termination   [ 1.20  ].....................[ 1.520   ]
CPU PLL           [ 1.50  ].....................[ 1.670   ]
CPU Reference     [ 0.760 ].....................[ 1.003   ]
 
MCH Core          [ 1.100 ].....................[ 1.560   ]
MCH Reference     [ 0.760 ].....................[ 0.963   ]
MCH/DRAM Refernce [ 0.900 ].....................[ 1.230   ]
ICH I/O           [ 1.500 ].....................[ 1.500   ]
ICH Core          [ 1.100 ].....................[ 1.100   ]
 
DRAM Voltage      [ 1.800 ].....................[ 2.460   ]
DRAM Termination  [ 0.900 ].....................[ 1.230   ]
Channel A Ref     [ 0.900 ].....................[ 1.230   ]
Channel B Ref     [ 0.900 ].....................[ 1.230   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

These are my current boot settings for 5.1+ and so far are good for spi 1m up to 5.13(570).

Code:

******Motherboard Intelligent Tweaker (M.I.T.)******
 
Robust Graphics Booster.........................[ Auto     ]
CPU Clock Ratio.................................[ 9        ]
Fine CPU Clock Ratio............................[ + 0.0    ]
CPU Frequency 5.1GHz............................[ 567 x 9.0]
 
******Clock Chip Control******
 
CPU Host Clock Control..........................[ Enabled  ]
CPU Host Frequency (Mhz)........................[ 567      ]
PCI Express Frequency (Mhz).....................[ 101      ]
C.I.A 2.........................................[ Disabled ]
 
******Advanced Clock Control******
 
CPU Clock Drive.................................[ 1000mv   ]
PCI Express Clock Drive.........................[ 1000mv   ]
CPU Clock Skew..................................[ 100ps    ]
MCH Clock Skew..................................[ 100ps    ]
 
******DRAM Performance Control******
 
Performance Enhance.............................[ Standard ]
(G) MCH Frequency Latch.........................[ 333      ]
System Memory Multipler.........................[ 2.00B    ]
Memory Frequency 1066...........................[ 1134     ]
DRAM Timing Selectable..........................[ Manual   ]
 
CAS Latency Time................................[ 4       ]
tRCD............................................[ 4       ]
tRP.............................................[ 4       ]
tRAS............................................[ 8       ]
 
******Advanced Timing Control******
 
tRRD[3].........................................[ 4       ]
tWTR[3].........................................[ 4       ]
tWR[6]..........................................[ 8       ]
tRFC[54]........................................[ 26      ]
tRTP[3].........................................[ 4       ]
Command Rate (cmd)[0]...........................[ Auto    ]
 
******Channel A Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 9       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]

tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel A Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Channel B Timing Settings******     
 
Static tRead Value        [ 8 ].................[ 9       ]
tRD Phase0 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase1 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase2 Adjustment     [ 0 ].................[ Auto    ]
tRD Phase3 Adjustment     [ 0 ].................[ Auto    ]
 
tRD 2rd (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2wr (Differnt Rank)   [ 8 ].................[ Auto    ]
tWR 2rd (Differnt Rank)   [ 7 ].................[ Auto    ]
tRD 2wr (Same/Difft Rank) [ 9 ].................[ Auto    ]
 
Dimm 1 Clock Skew Control.......................[ Auto    ]
Dimm 2 Clock Skew Control.......................[ Auto    ]
DDR Write Training..............................[ Auto    ]
 
******Channel B Driving Settings****** 
 
Drive Strength Profile..........................[ 1200    ]
Data Driving Pull Up Level......................[ Auto    ]
cmd Driving Pull Up Level.......................[ Auto    ]
ctrl Driving Pull Up Level......................[ Auto    ]
clk Driving Pull Up Level.......................[ Auto    ]
 
Data Driving Pull Down Level....................[ Auto    ]
cmd Driving Pull Down Level.....................[ Auto    ]
ctrl Driving Pull Down Level....................[ Auto    ]
clk Driving Pull Down Level.....................[ Auto    ]
 
******Motherboard Voltage Control******
 
Load-Line Calibration...........................[ Enabled ]
CPU Vcore         [ 1.15  ].....................[ 1.640   ]
CPU Termination   [ 1.20  ].....................[ 1.600   ]
CPU PLL           [ 1.50  ].....................[ 1.710   ]
CPU Reference     [ 0.760 ].....................[ 1.038   ]
 
MCH Core          [ 1.100 ].....................[ 1.600   ]
MCH Reference     [ 0.760 ].....................[ 1.013   ]
MCH/DRAM Refernce [ 0.900 ].....................[ 1.270   ]
ICH I/O           [ 1.500 ].....................[ 1.570   ]
ICH Core          [ 1.100 ].....................[ 1.200   ]
 
DRAM Voltage      [ 1.800 ].....................[ 2.540   ]
DRAM Termination  [ 0.900 ].....................[ 1.270   ]
Channel A Ref     [ 0.900 ].....................[ 1.270   ]
Channel B Ref     [ 0.900 ].....................[ 1.270   ]

******Advanced BIOS Features******
 
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ]
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

**NeoGeo333** · 05-21-2010, 11:06 PM

Originally Posted by NoGuru

To get the bubbles out you need to shake the case a bit and open the res and bleed them.
I don't think the is your problem though. I would remount the cooler.

bleed the bubbles out by slowing the pump down a few minutes and opening the res. that took care of the bubbles, remounted cpu block and now idle at 45'C, still think is high for a Q6600 at 3.6ghz at 1.38v?

**In-Fluence** · 05-22-2010, 12:13 AM

A lot better but still a little high for those volts. Is your CPU/cooler surface flat? If you remove the block, is the paste unevenly spread?

**NoGuru** · 05-22-2010, 06:03 AM

Originally Posted by In-Fluence

A lot better but still a little high for those volts. Is your CPU/cooler surface flat? If you remove the block, is the paste unevenly spread?

I agree.

What CPU block do you have, or the whole loop for that matter?
What method of applying TIM do you use?

**NeoGeo333** · 05-22-2010, 01:22 PM

Originally Posted by NoGuru

I agree.

What CPU block do you have, or the whole loop for that matter?
What method of applying TIM do you use?

Im using MX-3 and theres no formal way to apply other than a drop of it in the middle and thats it. Using a XSPC Rasa CPU Acetal block, dont know if its good for Q6600, or should have stock with Swiftech Apogee.

**andressergio** · 05-22-2010, 01:53 PM

Originally Posted by NeoGeo333

Im using MX-3 and theres no formal way to apply other than a drop of it in the middle and thats it. Using a XSPC Rasa CPU Acetal block, dont know if its good for Q6600, or should have stock with Swiftech Apogee.

i use the same just use a card to place a thin layer over the chip

**NeoGeo333** · 05-22-2010, 08:49 PM

I wonder if ambient at 85 to 86'F is the culprit. Hot nights in Puerto Rico is killer, now with a/c at max got it down to 38'C idle.

**truehighroller** · 05-23-2010, 06:21 AM

Originally Posted by NeoGeo333

I wonder if ambient at 85 to 86'F is the culprit. Hot nights in Puerto Rico is killer, now with a/c at max got it down to 38'C idle.

That' why your country ships the coke over here, it's hot LMAO.

**NeoGeo333** · 05-23-2010, 11:41 AM

Originally Posted by truehighroller

That' why your country ships the coke over here, it's hot LMAO.

Sure you know where Puerto Rico is? Its not in Mexico

**OCX600RR** · 05-23-2010, 01:21 PM

Quick Question - I've been running my E8400 at 4.0GHz at 1.2vcore on my P45-UD3P since I received the components, and I've never updated the BIOS on my motherboard. It's still running the F4 BIOS! Are there any advantaged to update to the latest BIOS? I've never messed around with updating BIOS's before, that's why I'm asking.

**NoGuru** · 05-23-2010, 04:18 PM

Originally Posted by OCX600RR

Quick Question - I've been running my E8400 at 4.0GHz at 1.2vcore on my P45-UD3P since I received the components, and I've never updated the BIOS on my motherboard. It's still running the F4 BIOS! Are there any advantaged to update to the latest BIOS? I've never messed around with updating BIOS's before, that's why I'm asking.

Hello fellow Michigander. Not really, if it's working fine no reason too change it.

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: ** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P