Originally Posted by
RAMMAN
i dont suppose anyone has a template for ddr2-1300 with micron d9 and a ud3 series board, preferably on the 5:8 divider? there must be something im missing. 1200 5-5-5-15 2.2v is stable but im hitting a brick wall in the high 1200s. 1300 5-5-5-15 pl9 2.4 vdimm 1.3 mch 0.8 mch ref errors just seconds into orthos and trying 6-6-6-18 pl10 had no effect on stability. i havent touched any of the drive strength or clock skew settings, maybe thats the key?
you can try mine.
Code:
*****Motherboard Intelligent Tweaker (M.I.T.)******
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ + 0.5 ]
CPU Frequency 3.6GHz............................[ 510 x 8.5 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 510 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 [Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 1000mv]
PCI Express Clock Drive.........................[ 900mv]
CPU Clock Skew..................................[ 0ps]
MCH Clock Skew..................................[ 50ps]
******DRAM Performance Control******
Performance Enhance.............................[Standard]
Extreme Memory Profile (XMP)....................[ Auto ]
(G) MCH Frequency Latch.........................[ 266 ]
System Memory Multiplier........................[ 2.50A ]
Memory Frequency ..............1066.............1275
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time...............[ 5 ].........[ 5 ]
tRCD...........................[ 5 ].........[ 5 ]
tRP............................[ 5 ].........[ 5 ]
tRAS...........................[ 15 ].........[ 15 ]
******Advanced Timing Control******
tRRD...........................[ 4 ]..........[ Auto ]
tWTR...........................[ 4 ]..........[ Auto ]
tWR............................[ 6 ]..........[ Auto ]
tRFC...........................[ 72 ].........[ 55 ]
tRTP...........................[ 4 ]..........[ Auto ]
Command Rate (cmd).............[ 0 ]..........[ 2 ]
******Channel A Timing Settings******
Static tRead Value [ 8 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 8 ] ................[ 8 ]
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 8 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 7 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ]
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration...........................[ Enabled ]
CPU Vcore [ 1.25 ]...................[ 1.418V ]
CPU Termination [ 1.20 ]...................[ 1.40 ]
CPU PLL [ 1.50 ]...................[ 1.57 ]
CPU Reference [ 0.760 ]...................[ 0.911 ]ET6 0.785
MCH Core [ 1.100 ]...................[ 1.40 ]
MCH Reference [ 0.760 ]...................[ 0.926 ]ET6 0.80
MCH/DRAM Refernce [ 0.900 ]...................[ Normal ]
ICH I/O [ 1.500 ]...................[ Normal ]
ICH Core [ 1.100 ]...................[ Normal ]
DRAM Voltage [1.8]...................[2.28 ]
DRAM Termination [0.9]...................[Normal]
Channel A Ref [0.9]...................[Normal]
Channel B Ref [0.9]...................[Normal]
*****************Advanced BIOS Features*********
Limit CPUID Max to 3 ................. [disable]
No-Execute memory Protect ............ [disable]
CPU Enhance Halt (CIE) ............... [disable]
C2/C2E State Support ................. [disable]
C4/C4E State Support ................. [disable]
CPU Thermal Monitor................... [disable]
CPU EIST Function..................... [disable]
Virtualization Technology ............ [disable]
Reply With Quote
Bookmarks