DFI UT X58-T3EH8 continued - Part 2

[Factotum]

do not use C1E - it's 100% crashing for idle. may be it dropped Vcore and x22 multiplier for a core
my settings 200*21 for save energy:

Genie BIOS Setting

CPU Feature
Set VR Current Limit Max: Enabled
Thermal Management Control: Disabled
EIST Function: Enabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

DRAM Timing
Channel Interleave Setting: AUTO
Rank Interleave Setting: AUTO
Memory LowGap: 1536M

DRAM Command Rate: 1N
CAS Latency Time (tCL): 7
RAS# to CAS# Delay (tRCD): 7
RAS# Precharge (tRP): 7
Precharge Delay (tRAS): 19
REF to ACT Delay (tRFC): 60
Write to PRE Delay (tWR): 10
Rank Write to Read (tWTR): 6
ACT to ACT Delay (tRRD): 6
Row Cycle Time (tRC): 30
Read CAS# Precharge (tRTP): 6
Four ACT WIN Time (tFAW): AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: Auto
CPU VID Special Add Limit: Enabled
CPU VID Special Add: 109.92%
Vcore Droop Control: Enabled
DRAM Bus Voltage: 1.620v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: AUTO
CPU VTT Voltage: 1.31
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.11v
IOH Analog Voltage: 1.10v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Enabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 20x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: 4.8GT/s
CPU Base Clock (BCLK): 200 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 100 Mhz
DRAM Frequency: 8x
UnCore Frequency: 16x

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

and Get:
IDLE - 200*12=2400MHz Vcore=1.056V, CPUvtt=1.28V
and full load: