Can anybody help me here?

I can't seem to get my E6600 to 3.6Ghz ...I get a BSOD on Windows startup or sometimes a few minutes into Windows at that speed.
With my previous mobo (680i), I was stable at 3.4Ghz with 1.30625v (1.288v CPU-Z) so voltage shouldn't be too much of an issue...even setting it to 1.4V yields the same result at 3.6Ghz. (Also, yes the RAM is stable if you were wondering)
These are the settings I tried for 3.6Ghz...

Code:
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9.0x
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3600Mhz


Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400 Mhz
PCI Express Frequency (Mhz) .........:100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< Default?
PCI Express Clock Drive.................: <<< Default?
CPU Clock Skew (ps)....................: <<< 0
MCH Clock Skew (ps)...................: <<< 0


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 2.00D
Memory Frequency (Mhz) ..............: 800Mhz
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15

Advanced Timing Control
tRRD...........................................Auto
tWTR..........................................Auto
tWR............................................Auto
tRFC...........................................Auto
tRTP...........................................Auto
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH - Auto
 tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH - Auto
 tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Motherboard Voltage Control
Voltage Type.………... Manual
CPU
CPU Vcore….……….........................:1.35v

CPU Termination…..... tried multiple... 1.26, 1.28, 1.30, 1.32V-none worked .. at most a few seconds into Orthos before BSOD
CPU PLL…………………....1.500V
CPU Reference.…………....Auto

MCH/ICH
MCH Core…………….....1.28V
MCH Reference….…….Auto
MCH/DRAM Ref.….....Auto
ICH I/O……………….....1.500V
ICH Core…………...……1.100V

DRAM
DRAM Voltage ……....1.840V
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Enabled]
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled]
Any suggestions?