DFI LP UT X58-T3EH8 - First bench, bios screens etc

**Shadowjump** · 04-30-2009, 02:32 PM

Meh, it was the CPUs after all!

Just changed to a D0 and with lower voltages i am doing 4.2 24/7

**eva2000** · 04-30-2009, 03:25 PM

yeah cpu plays an important part

**Marvin54** · 04-30-2009, 09:58 PM

eva2000:

The chipset is well cool, keep it as cold?

**Praz** · 05-02-2009, 07:33 AM

DFI LP UT X58-T3eH8, 02/17 BIOS
i7 920
3x2GB OCZ PC3-15000 Reaper CL9 1866MHz 9-9-9-28
3x2GB OCZ PC3-14400 Reaper CL8 1800MHz 8-8-8-26
200x20, Memory 1600MHz 7-7-7-24
HT On, Turbo Off
OCZ 120GB Apex
SAPPHIRE 4870 Crossfire
Green Slots Used For Memory

click for larger image

click for larger image

Code:

Genie BIOS Setting

Main BIOS Page
 Exit Setup Shut down:............Mode 2
 O.C. Fail Retry Counter:.........Enabled
 O.C. Fail CMOS Reload:...........Disabled

 PPM Function:....................Enabled
 Turbo Mode Function:.............Disabled
x 1 core Max Turbo Ratio:.........22x
x 2 core Max Turbo Ratio:.........21x
x 3 core Max Turbo Ratio:.........21x
x 4 core Max Turbo Ratio:.........21x
 CPU Non-Turbo Clock Ratio:.......20x

 * BCLK/UCLK/QPI Controller Settings *
 QPI Control Settings:............Enabled
 QPI Link Fast Mode:..............Enabled
 QPI Frequency:...................Auto
 CPU Base Clock(BCLK):............200 Mhz
 Boot Up CPU Base Clock:..........Auto
 PCIE Clock:......................100 Mhz
 DRAM Frequency:..................BCLK*08 Mhz
 UnCore Frequency:................BCLK*16 Mhz

 CPU Spread Spectrum:.............Disabled
 PCIE Spread Spectrum:............Disabled

CPU Feature
 Set VR Current Limit Max:........Enabled
 Thermal Management Control:......Enabled
 EIST Function:...................Enabled
 CxE Function:....................Auto
 Execute Disable Bit:.............Enabled
 Virtualization Technology:.......Enabled

  ***** Logical Processor Setting *****
 Intel HT Technology:.............Enabled
 Active Processor Cores:..........All

DRAM Timing
 Channel Interleave Setting:......Auto
 Rank Interleave Setting:.........Auto
 Memory LowGap:...................1536M

 DRAM Command Rate:...............1N
 CAS Latency Time (tCL):..........7
 RAS# to CAS# Delay (tRCD):.......7
 Precharge Delay (tRP):...........7
 RAS# Precharge (tRAS):...........24
 REF to ACT Delay (tRFC):.........Auto
 Write to PRE Delay (tWR):........Auto
 Rank Write to Read (tWTR):.......Auto
 ACT to ACT Delay (tRRD):.........Auto
 Row Cycle Time (tRC):............Auto
 Read CAS# Precharge (tRTP):......Auto
 Four ACT WIN Time (tFAW):........Auto

Voltage Setting
 O.C. Shut Down Free:.............Enable O.C.S.D.F
 CPU VID Control:.................1.32500V
 CPU VID Special Add Limit:.......Enabled
 CPU VID Special Add:.............Auto
 Vcore Droop Control:.............Enabled
 DRAM Bus Voltage:................1.680v
 DRAM PWM Switch Frequency:.......Nominal Frequency
 DRAM PWM Phase Control:..........2 Phase Operation
 CPU VTT Special Add:.............Auto
 CPU VTT Voltage:.................1.32v
 VTT PWM Switch Frequency:........Nominal Frequency
 VTT PWM Phase Control:...........2 Phase Operation
 CPU PLL Voltage:.................1.80v
 IOH/ICH 1.1V Voltage:............1.11v
 IOH Analog Voltage:..............1.10v
 ICH 1.5 Voltage:.................1.5v
 ICH 1.05V Voltage:...............1.05v
 DIMM 1/2 DQ/DQSTB Bus VREF:......+00.0%
 DIMM 3/4 DQ/DQSTB Bus VREF:......+00.0%
 DIMM 5/6 DQ/DQSTB Bus VREF:......+00.0%
 ADDR/CMD VREF Control:...........Disabled
x DIMM 1/2 ADDR/CMD Bus VREF:.....110
x DIMM 3/4 ADDR/CMD Bus VREF:.....110
x DIMM 5/6 ADDR/CMD Bus VREF:.....110
 CPU QPI Drive Strength:..........Normal
 IOH QPI Drive Strength:..........Normal

click for larger image

**Praz** · 05-02-2009, 07:34 AM

Windows 7 64Bit

click for larger image

click for larger image

3dx Max 2009 w/V-ray
Time to render: 6min 09sec

click for larger image

TMPGEnc XPress
1GB VOB file ripped from DVD movie

click for larger image

click for larger image

**eva2000** · 05-02-2009, 07:42 AM

Originally Posted by Marvin54

eva2000:

The chipset is well cool, keep it as cold?

you mean my system ? it's open bench setup with 120x25mm thermaltake 81cfm fan over NB

Praz very very nice IMC on that cpu for 12GB and cpu vtt 1.31v!!!

Max BCLK

Super Pi 1M to 32M

System:

i7 920 3836A756
EK Supreme LT 1366 / FESER 480 / MCP655
DFI UT X58-T3EH8 04/28 beta
512MB Inno3D 8800GT OC Edition
6GB Corsair Dominator GT DDR3-2000Mhz 7-8-7-20
750GB Samsung SATAII
Silverstone OP1200 PSU
Dual boot - WinXP Pro SP3 / Vista Ultimate 64Bit SP2

Bios settings used.

Code:

Genie BIOS Setting

CPU Feature
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Disabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

DRAM Timing
Channel Interleave Setting: AUTO
Rank Interleave Setting: AUTO
Memory LowGap: 1792M

DRAM Command Rate: AUTO
CAS Latency Time (tCL): 6
RAS# to CAS# Delay (tRCD): 7
RAS# Precharge (tRP): 6
Precharge Delay (tRAS): 20
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): 31
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): 31
Ch1 Round trip latency: AUTO (-15 to +16)
Ch2 Round trip latency: AUTO (-15 to +16)
Ch3 Round trip latency: AUTO (-15 to +16)
tREFI: AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1.4500v
CPU VID Special Add Limit: Disabled
CPU VID Special Add: 103.30%
Vcore Droop Control: Disabled
DRAM Bus Voltage: 1.71v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: 0.0875v
CPU VTT Voltage: 1.53v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.29v
IOH Analog Voltage: 1.20v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Disabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 19x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: AUTO
CPU Base Clock (BCLK): 230 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 110 Mhz
DRAM Frequency: 8xx Memory multipliers
UnCore Frequency: 16x Uncore multipliers

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

Starting to hit probably thermal limits of my i7 920 3836A756 on H20 cooling as 32M Pi seems to be topping out around 4680mhz with HT disabled. Only managed to shave ~1 second off my best 32M pi time with i7 920.

**msgclb** · 05-05-2009, 07:41 AM

Originally Posted by eva2000

System:

i7 920 3836A756
EK Supreme LT 1366 / FESER 480 / MCP655
DFI UT X58-T3EH8 04/28 beta
512MB Inno3D 8800GT OC Edition
6GB Corsair Dominator GT DDR3-2000Mhz 7-8-7-20
750GB Samsung SATAII
Silverstone OP1200 PSU
Dual boot - WinXP Pro SP3 / Vista Ultimate 64Bit SP2

Does your experience using a Feser Quad with the DFI UT X58 tell you that it's needed or did you just get a good deal

? Ever since I noticed that you went with a quad I've been looking but over here all I see is 'Out of Stock'.

**Praz** · 05-05-2009, 03:09 PM

DFI LP UT X58-T3eH8, 04/28 BIOS
i7 920
3x2GB OCZ PC3-14400 Reaper 1800MHz 8-8-8-26
225x18, Memory 1800MHz 8-8-8-24
HT On, Turbo Off
OCZ 30GB Vertex
OCZ 120GB Apex
SAPPHIRE 4870 Crossfire
OCZ 1000WProXStream - 4 Rail Modified To Single Rail

click for larger image

click for larger image

Code:

Genie BIOS Setting

Main BIOS Page
 Exit Setup Shut down:............Mode 2
 O.C. Fail Retry Counter:.........Enabled
 O.C. Fail CMOS Reload:...........Disabled

 PPM Function:....................Disabled
 Turbo Mode Function:.............Disabled
x 1 core Max Turbo Ratio:.........22x
x 2 core Max Turbo Ratio:.........21x
x 3 core Max Turbo Ratio:.........21x
x 4 core Max Turbo Ratio:.........21x
 CPU Non-Turbo Clock Ratio:.......18x

 * BCLK/UCLK/QPI Controller Settings *
 QPI Control Settings:............Enabled
 QPI Link Fast Mode:..............Enabled
 QPI Frequency:...................Auto
 CPU Base Clock(BCLK):............225 Mhz
 Boot Up CPU Base Clock:..........Auto
 PCIE Clock:......................100 Mhz
 DRAM Frequency:..................BCLK*08 Mhz
 UnCore Frequency:................BCLK*16 Mhz

 CPU Spread Spectrum:.............Disabled
 PCIE Spread Spectrum:............Disabled

CPU Feature
 Set VR Current Limit Max:........Enabled
 Thermal Management Control:......Disabled
 EIST Function:...................Enabled
 CxE Function:....................Auto
 Execute Disable Bit:.............Enabled
 Virtualization Technology:.......Enabled

  ***** Logical Processor Setting *****
 Intel HT Technology:.............Enabled
 Active Processor Cores:..........All

DRAM Timing
 Channel Interleave Setting:......Auto
 Rank Interleave Setting:.........Auto
 Memory LowGap:...................1536M

 DRAM Command Rate:...............1N
 CAS Latency Time (tCL):..........8
 RAS# to CAS# Delay (tRCD):.......8
 Precharge Delay (tRP):...........8
 RAS# Precharge (tRAS):...........24
 REF to ACT Delay (tRFC):.........74
 Write to PRE Delay (tWR):........Auto
 Rank Write to Read (tWTR):.......Auto
 ACT to ACT Delay (tRRD):.........5
 Row Cycle Time (tRC):............Auto
 Read CAS# Precharge (tRTP):......Auto
 Four ACT WIN Time (tFAW):........20
 Ch1 Round trip latency...........Auto
 Ch1 Round trip latency...........Auto
 Ch1 Round trip latency...........+1
 tREFI............................Auto

Voltage Setting
 O.C. Shut Down Free:.............Enable O.C.S.D.F
 CPU VID Control:.................1.36875
 CPU VID Special Add Limit:.......Disabled
 CPU VID Special Add:.............103.77%
 Vcore Droop Control:.............Enabled
 DRAM Bus Voltage:................1.650v
 DRAM PWM Switch Frequency:.......Nominal Frequency
 DRAM PWM Phase Control:..........2 Phase Operation
 CPU VTT Special Add:.............Auto
 CPU VTT Voltage:.................1.34v
 VTT PWM Switch Frequency:........Nominal Frequency
 VTT PWM Phase Control:...........2 Phase Operation
 CPU PLL Voltage:.................1.80v
 IOH/ICH 1.1V Voltage:............1.15v
 IOH Analog Voltage:..............1.10v
 ICH 1.5 Voltage:.................1.5v
 ICH 1.05V Voltage:...............1.05v
 DIMM 1/2 DQ/DQSTB Bus VREF:......-00.0%
 DIMM 3/4 DQ/DQSTB Bus VREF:......-00.0%
 DIMM 5/6 DQ/DQSTB Bus VREF:......-00.0%
 ADDR/CMD VREF Control:...........Disabled
x DIMM 1/2 ADDR/CMD Bus VREF:.....110
x DIMM 3/4 ADDR/CMD Bus VREF:.....110
x DIMM 5/6 ADDR/CMD Bus VREF:.....110
 CPU QPI Drive Strength:..........Strong
 IOH QPI Drive Strength:..........Normal

click for larger image

CPU-Z Validation

**Praz** · 05-05-2009, 03:10 PM

Windows 7 64Bit

click for larger image

click for larger image

3dx Max 2009 w/V-ray
Time to render: 5min 56sec

click for larger image

TMPGEnc XPress
1GB VOB file ripped from DVD movie

click for larger image

click for larger image

**eva2000** · 05-05-2009, 05:37 PM

nice Praz, total SSD based system I see

Originally Posted by msgclb

Does your experience using a Feser Quad with the DFI UT X58 tell you that it's needed or did you just get a good deal

? Ever since I noticed that you went with a quad I've been looking but over here all I see is 'Out of Stock'.

Well feser 480 was selling at feser 360 prices here locally as retailer was doing a special to make up for the fact he didn't have feser 360 stock - so choice was obvious

4//28 looking sweet indeed 8x 32M Super Pi instance via HyperPi @DDR3-2080Mhz 7-8-7-20 1T at 1.725v bios set vdimm = 1.730v real DMM vdimm.

New SG Skin used http://i4memory.com/f80/dfi-ut-x58-t...n-skins-17321/

Both cstkl1 and my DFI contact suggested with 4/28 bios, I check out setting BOOT Up CPU Base Clock to around 180-185bclk for better perrformance and stability. Seems to work as first test has me reducing my required CPU VTT volts from 1.43v to 1.37v for 8x 32M Pi test!!!!

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: AUTO
CPU Base Clock (BCLK): 200 Mhz
Boot Up CPU Base Clock: 185 Mhz
PCIE Clock: 104 Mhz
DRAM Frequency: 10x Memory multipliers
UnCore Frequency: 20x Uncore multipliers

Bumped CPU VTT from 1.37v bios to 1.39v bios and IOH/ICH v1.1 from 1.11 to 1.13v for Linx stability

**Peakr** · 05-05-2009, 11:02 PM

Any word on DFI putting this awesomeness into a bios for the DK?

**eva2000** · 05-05-2009, 11:29 PM

DFI DK X58 and JR X58 4/28 beta here http://i4memory.com/f80/dfi-dk-x58-t...-public-17312/

**Peakr** · 05-05-2009, 11:43 PM

Sweet.THX!

**Praz** · 05-07-2009, 09:20 AM

Originally Posted by eva2000

nice Praz, total SSD based system I see

Thanks Eva. With no conventional hard drives the system feels so much smoother. Had a bit of time last night and it looks lke 230 BCLK might have a chance at 24/7 stability. It's passing 20 runs of LinX. Haven't tried other benches yet.

**cstkl1** · 05-08-2009, 02:42 AM

Will post pic and more results later on higher vdimm..

For DFI x58's

I find memtest hci and memtest86+ is fake on vdimm
hyperpi is somewhat fake cause all u need is to have stable vtt voltages
it will accept lower vdimm a lot by around 0..05v
prime95 set large fft then custom change run fft to 5.4gb is the best for vdimm
linx is best for vcore and ioh/ich voltages.

Test rig
I7 920
DFI UT X58 the8
Kingston Hyperx T1 3x2gb 2000mhz CL8
GTx285 sli.

1.65v set DMM Read 1.648 load

2100mhz 8-8-8-24 1n

had to abort linx but i did find the exact vcore from another method.
will use hr05 later and some fans on the nb. havent placed them yet on this 2nd mobo

**eva2000** · 05-10-2009, 06:56 AM

Originally Posted by Praz

Thanks Eva. With no conventional hard drives the system feels so much smoother. Had a bit of time last night and it looks lke 230 BCLK might have a chance at 24/7 stability. It's passing 20 runs of LinX. Haven't tried other benches yet.

230bclk i7 920 C0 linx stable dam nice!

Originally Posted by cstkl1

Will post pic and more results later on higher vdimm..

For DFI x58's

I find memtest hci and memtest86+ is fake on vdimm
hyperpi is somewhat fake cause all u need is to have stable vtt voltages
it will accept lower vdimm a lot by around 0..05v
prime95 set large fft then custom change run fft to 5.4gb is the best for vdimm
linx is best for vcore and ioh/ich voltages.

Test rig
I7 920
DFI UT X58 the8
Kingston Hyperx T1 3x2gb 2000mhz CL8
GTx285 sli.

1.65v set DMM Read 1.648 load

2100mhz 8-8-8-24 1n

had to abort linx but i did find the exact vcore from another method.
will use hr05 later and some fans on the nb. havent placed them yet on this 2nd mobo

nice.. seem to have gotten the trick to DFI UT X58-T3EH8 Elpida clocking

My latest HD4870x2 Crossfire results

System:

i7 920 3836A756
EK Supreme LT 1366 / FESER 480 / MCP655
DFI UT X58-T3EH8 04/28 beta
2x HD4870x2 Crossfire (Powercolor + Gigabyte flashed to Asus Top bios) with ATI Win7 9.4 (8.612 WHQL)
6GB Corsair Dominator GT DDR3-2000Mhz 7-8-7-20
750GB Samsung SATAII
Silverstone OP1200 PSU
Triple boot - WinXP Pro SP3 / Vista Ultimate 64Bit SP2 / Win7 Ultimate 64bit RC

3dmark2003 get the following error when i start it ??

Problem signature:
Problem Event Name: APPCRASH
Application Name: 3DMark03.exe
Application Version: 3.6.0.0
Application Timestamp: 41da8282
Fault Module Name: fmod.dll
Fault Module Version: 3.6.1.0
Fault Module Timestamp: 3e170d1b
Exception Code: c0000005
Exception Offset: 000109ca
OS Version: 6.1.7100.2.0.0.256.1
Locale ID: 1033
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789

Read our privacy statement online:
http://go.microsoft.com/fwlink/?link...8&clcid=0x0409

If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt

Throw in some wprime

**hadji_a** · 05-12-2009, 06:13 AM

I have a problem getting the 21 multi to work in win7 7100 x64. I have eist and turbo enabled in the bios (4/28) but only seem to get 12 multi (as shown in cpuz and confirmed by results from various benches) within windows. Power plan is set to high performance (min and max are set to 100%). I have no problem using 21 multi in both xp and 2k8.
Any suggestions would be much appreciated.

**eva2000** · 05-12-2009, 06:51 AM

Originally Posted by hadji_a

I have a problem getting the 21 multi to work in win7 7100 x64. I have eist and turbo enabled in the bios (4/28) but only seem to get 12 multi (as shown in cpuz and confirmed by results from various benches) within windows. Power plan is set to high performance (min and max are set to 100%). I have no problem using 21 multi in both xp and 2k8.
Any suggestions would be much appreciated.

A few of us are discussing same experience with win7 at http://i4memory.com/f80/windows-7-df...8-t3eh8-17336/, some findings are VID Special Add set to AUTO fixes it (although i didn't have problems with it set to disabled) and also that cpuz is incorrectly reporting lower multipliers when turbo 21x multi is enabled - as my benchmarks are all showing results reflective of 21x being in place even if cpuz fluctuates for me between 5x, 8x, 12x, 15x, 17x, 18x, 20x and 21x in windows 7

Proof that cpuz reported cpu multiplier fluctuations in Windows 7 is cpuz related as both realtemp 3.20RC4 and coretemp 0.99.5 reported right 21x multi all the time

Fluctuating

**peebi** · 05-12-2009, 06:55 AM

Originally Posted by hadji_a

I have a problem getting the 21 multi to work in win7 7100 x64. I have eist and turbo enabled in the bios (4/28) but only seem to get 12 multi (as shown in cpuz and confirmed by results from various benches) within windows. Power plan is set to high performance (min and max are set to 100%). I have no problem using 21 multi in both xp and 2k8.
Any suggestions would be much appreciated.

Same me
Then I change to xp

**eva2000** · 05-12-2009, 06:58 AM

Originally Posted by peebi

Same me
Then I change to xp

I suspect it's just cpuz misreporting - try with VID Special Add left at AUTO instead of disabled... no problems for me in terms of end result performance

**ci2kla** · 05-12-2009, 07:23 AM

Hey guys got back to DFI since UT-X48-T3RS.

Beta BIOS of 0805 is out anybody tried?

BTW my PWM area temp is getting ultra high...72C @ idle...maybe RMA time?...

**unclewebb** · 05-12-2009, 07:40 AM

The i7 Turbo tool might help you guys understand any problems you're having with your reported multiplier.

http://www.fileden.com/files/2008/3/3/1794507/Turbo.zip

With Core i7 there are two ways to read the multiplier. You can read it directly from a model specific register (MSR) within the processor or the Intel Turbo White Paper recommends that you compare two high performance timers within the CPU every second and calculate the average multiplier.

The i7 Turbo tool uses both of these methods so you can compare. Calculating the multiplier at full load is the most accurate way to read the multiplier but most software doesn't do this because it is a lot easier to just read one value from an MSR. Using Intel's method to calculate the multiplier when the CPU is idle is not 100% accurate but it's pretty close. It may result in the odd random value but 99.9% of the time it seems to be accurate at idle as well. Constant fluctuation at idle in the calculated multiplier is usually a sign that your Minimum processor power state in your Power Options is not in agreement with your EIST/C1E bios settings.

When running high stress programs like LinX, this tool is the best way to check that Turbo mode is staying fully engaged. As soon as the multi starts to drop at full load, that is a sign that Turbo mode is starting to cycle rapidly on and off.

**peebi** · 05-12-2009, 07:43 AM

[QUOTE=eva2000;3784216]I suspect it's just cpuz misreporting - try with VID Special Add left at AUTO instead of disabled... no problems for me in terms of end result performance

Please tell me about vid special add and vtt special add
Why it red mark
Is it save for 24/7

**Praz** · 05-12-2009, 07:50 AM

Originally Posted by eva2000

no problems for me in terms of end result performance

Same here with Win7 RC. Performance, temps and current draw indicate the multiplier is indeed 21x.

**cstkl1** · 05-12-2009, 11:44 AM

Pic kindda big.. but 4.4ghz ht off 2100mhz CL8
currently my fastest linx run 191.7

Thread: DFI LP UT X58-T3EH8 - First bench, bios screens etc

Thread Tools

Search Thread

Rate This Thread

Display

LP UT-X58-T3eH8 - 920 @ 200x20, 12GB Memory @ 1600MHz, Post 1 Of 2

LP UT-X58-T3eH8 - 920 @ 200x20, 12GB Memory @ 1600MHz, Post 2 Of 2

920 @ 225x18 6GB Memory 1800MHz, 8-8-8-24 - Post 1 Of 2

920 @ 225x18 6GB Memory 1800MHz, 8-8-8-24 - Post 2 Of 2

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions