Quote Originally Posted by Marvin54 View Post
eva2000:

The chipset is well cool, keep it as cold?
you mean my system ? it's open bench setup with 120x25mm thermaltake 81cfm fan over NB

Praz very very nice IMC on that cpu for 12GB and cpu vtt 1.31v!!!


Max BCLK






Super Pi 1M to 32M






System:
  • i7 920 3836A756
  • EK Supreme LT 1366 / FESER 480 / MCP655
  • DFI UT X58-T3EH8 04/28 beta
  • 512MB Inno3D 8800GT OC Edition
  • 6GB Corsair Dominator GT DDR3-2000Mhz 7-8-7-20
  • 750GB Samsung SATAII
  • Silverstone OP1200 PSU
  • Dual boot - WinXP Pro SP3 / Vista Ultimate 64Bit SP2



Bios settings used.

Code:
Genie BIOS Setting

CPU Feature
Set VR Current Limit Max: Disabled
Thermal Management Control: Disabled
EIST Function: Disabled
CxE Function: Disabled
Execute Disable Bit: Disabled
Virtualization Technology: Disabled

***** Logical Processor Setting *****
Intel HT Technology: Enabled
Active Processor Cores: All

DRAM Timing
Channel Interleave Setting: AUTO
Rank Interleave Setting: AUTO
Memory LowGap: 1792M

DRAM Command Rate: AUTO
CAS Latency Time (tCL): 6
RAS# to CAS# Delay (tRCD): 7
RAS# Precharge (tRP): 6
Precharge Delay (tRAS): 20
REF to ACT Delay (tRFC): AUTO
Write to PRE Delay (tWR): AUTO
Rank Write to Read (tWTR): AUTO
ACT to ACT Delay (tRRD): AUTO
Row Cycle Time (tRC): 31
Read CAS# Precharge (tRTP): AUTO
Four ACT WIN Time (tFAW): 31
Ch1 Round trip latency: AUTO (-15 to +16)
Ch2 Round trip latency: AUTO (-15 to +16)
Ch3 Round trip latency: AUTO (-15 to +16)
tREFI: AUTO

Voltage Setting
O.C. Shut Down Free: Enable O.C.S.D.F
CPU VID Control: 1.4500v
CPU VID Special Add Limit: Disabled
CPU VID Special Add: 103.30%
Vcore Droop Control: Disabled
DRAM Bus Voltage: 1.71v
DRAM PWM Switch Frequency: Nominal
DRAM PWM Phase Control: 2 Phase Operation
CPU VTT Special Add: 0.0875v
CPU VTT Voltage: 1.53v
VTT PWM Switch Frequency: Nominal
VTT PWM Phase Control: 2 Phase Operation
CPU PLL Voltage: 1.80v
IOH/ICH 1.1V Voltage: 1.29v
IOH Analog Voltage: 1.20v
ICH 1.5 Voltage: 1.5v
ICH 1.05V Voltage: 1.05v
DIMM 1/2 DQ/DQSTB Bus VREF: -00.0%
DIMM 3/4 DQ/DQSTB Bus VREF: -00.0%
DIMM 5/6 DQ/DQSTB Bus VREF: -00.0%
ADDR/CMD VREF Control: Disabled
x DIMM 1/2 ADDR/CMD Bus VREF: 110
x DIMM 3/4 ADDR/CMD Bus VREF: 110
x DIMM 5/6 ADDR/CMD Bus VREF: 110
CPU QPI Drive Strength: Normal
IOH QPI Drive Strength: Normal

Exit Setup Shut down: Mode 2
O.C. Fail Retry Counter: Enabled
O.C. Fail CMOS Reload: Disabled

PPM Function: Enabled
Turbo Mode Function: Disabled
1 core Max Turbo Ratio: 22x
2 core Max Turbo Ratio: 21x
3 core Max Turbo Ratio: 21x
4 core Max Turbo Ratio: 21x
CPU Non-Turbo Clock Ratio: 19x

* BCLK/UCLK/QPI Controller Settings *
QPI Control Settings: Enabled
QPI Link Fast Mode: Enabled
QPI Frequency: AUTO
CPU Base Clock (BCLK): 230 Mhz
Boot Up CPU Base Clock: AUTO
PCIE Clock: 110 Mhz
DRAM Frequency: 8xx Memory multipliers
UnCore Frequency: 16x Uncore multipliers

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
Starting to hit probably thermal limits of my i7 920 3836A756 on H20 cooling as 32M Pi seems to be topping out around 4680mhz with HT disabled. Only managed to shave ~1 second off my best 32M pi time with i7 920.