UnOfficial Asus Rampage II Extreme Thread

[DR3]

Just got around to benchmarking my latest rig and was very supprised at the poor results.
Even using the most basic bench of wPrime v1.55, 32M - 8.5+ sec and 1024 is 269.6+ seconds.
This seems very poor to me and when compared to the same CPU and memory of other systems on HWbot.com they are definatly poor.

I have tried almost everything I can think of to no avail.
Any help is truely appreiciated.

System config
MB - Asus Rampage 2 Extreme V2
BIOS - 1306
CPU - i920
RAM - OCZ Blade Series 6GB (3 x 2GB) DDR3 2000 (PC3 16000)
CPU Cooler - VapoChill Lightspeed (Phase Cooler -45C +)
Liquid Cooling - Koolance Exos 2.5 (1000w)
VGA - Sapphire HD4870x2 watercooled
PSU - Thermaltake Toughpower 1200w
HDD - Intel X25-M SSD
----------------------------------------------
AI overclock - manual
OC from CPU level up - auto
OC from Memory level up - auto
CPU Ratio setting - 21
CPU Turbo Power Limit - disable

CPU configuration 
CPU Ratio Setting - 21
C1E Support - disable
Hardware prefetcher - enable
Adjacent Cache line prefetcher - enable 
Intel Virtualization tech - disabled
CPU TM Function - disable
Execute Disabled bit - disabled
Intel HT Technology - disable
Active Processor Cores - all
A20M - disabled
Intel C-STATE tech - disabled

BCLK frequency - 200
PCIE frequency - 100
DRAM frequency - DDR3 1603MHz
UCLK frequency - 3208MHz
QPI frequency - auto

Dram timing control 
1st iformation - Insert Timings Here in 

6-6-6-14-A(5)-A(74)-A(10)-A(7)-A(16)-A(0)
2nd information - Insert Timings Here in 1N-A(55)-A(58)-A(61)
3rd information - Insert Timings Here in 

A(8)-A(8)-A(16)-A(7)-A(7)-A(7)-A(7)-A(6)-A(4)-A(7)-A(7)-A(4)

EPU II phase control - full phase
Load-line calibration - enable
CPU differential amplitude - auto
Extreme OV - disabled


Cpu voltage - 1.40000
CPU PLL voltage - auto
QPI-Dram voltage - auto

IOH voltage - auto
IOH PCIE voltage - auto
ICH voltage- auto
ICH PCIE voltage - auto

DRAM Bus voltage - 1.65681
DRAM REF voltage - auto

Debug mode - string
Keyboard TeakIt comtrol - disabled

CPU spread spectrum - disabled 
PCIE spectrum - disabled
CPU clock skew - auto
IOH clock skew - auto

[2chesapeakes]

Just got around to benchmarking my latest rig and was very supprised at the poor results.
Even using the most basic bench of wPrime v1.55, 32M - 8.5+ sec and 1024 is 269.6+ seconds.
This seems very poor to me and when compared to the same CPU and memory of other systems on HWbot.com they are definatly poor.

I have tried almost everything I can think of to no avail.
Any help is truely appreiciated.

System config
MB - Asus Rampage 2 Extreme V2
BIOS - 1306
CPU - i920
RAM - OCZ Blade Series 6GB (3 x 2GB) DDR3 2000 (PC3 16000)
CPU Cooler - VapoChill Lightspeed (Phase Cooler -45C +)
Liquid Cooling - Koolance Exos 2.5 (1000w)
VGA - Sapphire HD4870x2 watercooled
PSU - Thermaltake Toughpower 1200w
HDD - Intel X25-M SSD
----------------------------------------------
AI overclock - manual
OC from CPU level up - auto
OC from Memory level up - auto
CPU Ratio setting - 21
CPU Turbo Power Limit - disable

CPU configuration 
CPU Ratio Setting - 21
C1E Support - disable
Hardware prefetcher - enable
Adjacent Cache line prefetcher - enable 
Intel Virtualization tech - disabled
CPU TM Function - disable
Execute Disabled bit - disabled
Intel HT Technology - disable
Active Processor Cores - all
A20M - disabled
Intel C-STATE tech - disabled

BCLK frequency - 200
PCIE frequency - 100
DRAM frequency - DDR3 1603MHz
UCLK frequency - 3208MHz
QPI frequency - auto

Dram timing control 
1st iformation - Insert Timings Here in 

6-6-6-14-A(5)-A(74)-A(10)-A(7)-A(16)-A(0)
2nd information - Insert Timings Here in 1N-A(55)-A(58)-A(61)
3rd information - Insert Timings Here in 

A(8)-A(8)-A(16)-A(7)-A(7)-A(7)-A(7)-A(6)-A(4)-A(7)-A(7)-A(4)

EPU II phase control - full phase
Load-line calibration - enable
CPU differential amplitude - auto
Extreme OV - disabled


Cpu voltage - 1.40000
CPU PLL voltage - auto
QPI-Dram voltage - auto

IOH voltage - auto
IOH PCIE voltage - auto
ICH voltage- auto
ICH PCIE voltage - auto

DRAM Bus voltage - 1.65681
DRAM REF voltage - auto

Debug mode - string
Keyboard TeakIt comtrol - disabled

CPU spread spectrum - disabled 
PCIE spectrum - disabled
CPU clock skew - auto
IOH clock skew - auto

From the template it appears you have disable HT. By doing this with wprime you have reduced the number cores to 4 enable HT then set number of threads to 8 and you should score lower times.

[DR3]

From the template it appears you have disable HT. By doing this with wprime you have reduced the number cores to 4 enable HT then set number of threads to 8 and you should score lower times.

In looking at the wPrime scores on HWBot it does seem that all the low scores are with 4 cores and 8 threads so HT must be enabled. Will give it a shot.

Thanks for the keen eye.

[DR3]

From the template it appears you have disable HT. By doing this with wprime you have reduced the number cores to 4 enable HT then set number of threads to 8 and you should score lower times.

Enabling HT did lower the scores, but they are still not inline with others.
Will have to go back and do some benchmarking to find the problem.
I am positive that SpeedStep and C1E have to disabled.
Now to test the other settings to see how they affect things.