Live MB OC Report :: ASUS Rampage Extreme

[cheapseats]

Just got this board, anyone has a template on settings to get 4.0 stable? Will be used for gaming only.

Im using 1003 BIOS and I am running a E8600

Patriot DDR3 PVS34G1600LLK 4GB

hi dctokyo

unless you want higher memory clocks / memory performance, these board settings for 4x1GB could be ok or as a starting point.

Only tested with 32-bit and 0403 BIOS




some test settings not included below (shown as xxxxx): vcore / vDIMM / tRCD / tRP / tRAS / tRFC

AI OVERCLOCK TUNER =========================MANUAL
OC FROM CPU LEVEL ==========================AUTO
OC FROM MEMORY LEVEL UP ====================AUTO
FSB FREQUENCY ==============================498 / 499 / 500 (500 = lowest Everest Read)
CPU RATIO SETTING ==========================8

CPU CLOCK SKEW =============================AUTO
NB CLOCK SKEW ==============================AUTO
FSB STRAP TO NORTH BRIDGE ==================333
PCIE FREQUENCY =============================100
DRAM FREQUENCY =============================1603
DRAM COMAND RATE ===========================1N
DRAM TIMING CONTROL ========================MANUAL
CAS LATENCY ================================7
RAS TO CAS DELAY ===========================xxxxx 
RAS PRE TIME ===============================xxxxx 
RAS ACT TIME ===============================xxxxx 
RAS TO RAS DELAY ===========================AUTO
REF CYCLE TIME =============================AUTO 
WRITE RECOVERY TIME ========================AUTO
READ TO PRE TIME ===========================AUTO
READ TO WRITE DELAY S/D ====================AUTO
WRITE TO READ DELAY S ======================AUTO
WRITE TO READ DELAY D ======================AUTO
READ TO READ DELAY S =======================AUTO
READ TO READ DELAY D =======================AUTO
WRITE TO WRITE DELAY S =====================AUTO
WRITE TO WRITE DELAY D =====================AUTO
WRITE TO PRE DELAY =========================AUTO
READ TO PRE DELAY ==========================AUTO
PRE TO PRE DELAY ===========================AUTO
ALL PRE TO ACT DELAY =======================AUTO
ALL PRE TO REF DELAY =======================AUTO
DRAM STATIC READ CONTROL ===================AUTO
DRAM DYNAMIC WRITE CONTROL =================AUTO

DRAM SKEW CONTROL
DRAM CMD SKEW ON CHANNEL A = AUTO
DRAM CLK SKEW ON DIMM A1 = AUTO
DRAM CLK SKEW ON DIMM A2 = AUTO
DRAM CTL SKEW ON DIMM A1 = AUTO
DRAM CTL SKEW ON DIMM A2 = AUTO

DRAM CMD SKEW ON CHANNEL B = AUTO
DRAM CLK SKEW ON DIMM B1 = AUTO
DRAM CLK SKEW ON DIMM B2 = AUTO
DRAM CTL SKEW ON DIMM B1 = AUTO
DRAM CTL SKEW ON DIMM B2 = AUTO


AI CLOCK TWISTER ===========================MODERATE
AI TRANSACTION BOOSTER =====================MANUAL
PERFORMANCE LEVEL ==========================08

PULL-IN OF CHA PH1 =========================DISABLED
PULL-IN OF CHA PH2 =========================DISABLED
PULL-IN OF CHA PH3 =========================DISABLED
PULL-IN OF CHA PH4 =========================DISABLED
PULL-IN OF CHA PH5 =========================DISABLED
PULL-IN OF CHB PH1 =========================DISABLED
PULL-IN OF CHB PH2 =========================DISABLED
PULL-IN OF CHB PH3 =========================DISABLED
PULL-IN OF CHB PH4 =========================DISABLED
PULL-IN OF CHB PH5 =========================DISABLED

EPU II PHASE CONTROL =======================AUTO
CPU VOLTAGE ================================xxxxx  
LOAD-LINE CALIBRATION ======================DISABLED
CPU PLL VOLTAGE  ===========================1.51V (min)
FSB TERMINATION VOLTAGE  ===================min-1.20V 
CPU GTLVREF 0 ==============================AUTO / +40mV
CPU GTLVREF 1 ==============================AUTO
CPU GTLVREF 2 ==============================AUTO
CPU GTLVREF 3 ==============================AUTO
NB GTLVREF =================================AUTO
NORTH BRIDGE VOLTAGE =======================1.25V (min)
DRAM VOLTAGE ===============================xxxxx
NB DDRVREF =================================AUTO
DDR3 CHANNEL A VREF ========================AUTO
DDR3 CHANNEL B VREF ========================AUTO
SOUTH BRIDGE 1.5 VOLTAGE ===================1.51V (min)
SOUTH BRIDGE 1.05 VOLTAGE ==================1.06V (min)
CPU SPREAD SPRECTRUM =======================DISABLED
PCIE SPREAD SPECTRUM =======================DISABLED

Hello to everyone and what a great bunch of techno wizards you all are.

I need help please as I recently got my hands on a pair of DDR3 Dominator TWIN3X2048-1800C7DF 2x1 Gig and would love to know what would the ideal CPU, RAM & NB Bios seetings be for the highest stable clock.
Matching the RAM is an E8600 and a BFG 8500 512 GTS. CPU, NB & GPU are all watercooled on a Zalman XT which sits under a window and gets me great low temps. Will take pictures and post soon.
Much obliged for any help


PS. Didnt get the chance to change my sig. Doing it now.

nice to see you back buddy

hope to be testing same mems myself by this weekend unless version number is not for me...