** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

**xbiusx** · 02-04-2009, 12:17 PM

Hi, i need some advices to reach over 500 FSB, now i`m stable at 500x8 but my intentions are reach 530x8 or the max as i can. But my first attempts were frustrating. With 510x8 i got my CPU stable ran ORTHOS 1h small FTT and no errors. But blend test gave error before 1min, so there is some wrong with my settings about the memory. And please take a look and let me know what can i do.

Bios F7 settings

Code:

****** Gigabyte EP45 UD3P Bios F7 ******

E8500 500 X 8 4000MHz 

Robust Graphics Booster.........................[ Auto     ] 
CPU Clock Ratio.................................[ 8        ] 
Fine CPU Clock Ratio............................[ 0        ] 
CPU Frequency 4.0GHz...........................[ 500 x 8  ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled  ] 
CPU Host Frequency (Mhz)........................[ 510      ] 
PCI Express Frequency (Mhz).....................[ 102      ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv   ] 
PCI Express Clock Drive.........................[ 900mv   ] 
CPU Clock Skew..................................[ 0ps] 
MCH Clock Skew..................................[ 0ps     ] 

******DRAM Performance Control******

Performance Enhance.............................[ Standard ] 
Extreme Memory Profile (XMP)....................[ Disabled ] 
(G) MCH Frequency Latch.........................[ 400MHz   ] 
System Memory Multipler.........................[ 2.00D    ] 
Memory Frequency 1066...........................[ 1000      ] 
DRAM Timing Selectable..........................[ Manual   ] 

CAS Latency Time................................[ 5        ] Tried auto
tRCD............................................[ 5        ] Tried auto
tRP.............................................[ 5        ] Tried auto
tRAS............................................[ 18       ] Tried auto

******Advanced Timing Control******

tRRD............................................[ 4        ] [Auto] 
tWTR............................................[ 4        ] [Auto] 
tWR.............................................[ 8        ] [Auto] 
tRFC............................................[ 54       ] [Auto] Tried 54 ~ 72
tRTP............................................[ 4        ] [Auto] 
Command Rate (cmd)..............................[ 2T       ] 

******Channel A Timing Settings******     

Static tRead Value        [ 11 ] ................[ 9     ] Tried 9,10,11
tRD Phase0 Adjustment     [ 1 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ Auto     ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Channel B Timing Settings******     

Static tRead Value        [ 11 ] ................[ 9     ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ Auto     ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Disabled ] 
CPU Vcore         [ 1.25000 ]...................[ 1.36250 ] Tried ~ 1.37500
CPU Termination   [ 1.20    ]...................[ 1.28  ]
CPU PLL           [ 1.50    ]...................[ 1.5000  ]  
CPU Reference     [ 0.760   ]...................[Normal     ] 

MCH Core          [1.100    ]...................[ 1.400   ]  Tried 1.420
MCH Reference     [0.760    ]...................[ 0.750     ] ET6 show 0.720 Tried 0.700
MCH/DRAM Refernce [0.900    ]...................[ Normal     ] 
ICH I/O           [1.500    ]...................[ 1.500     ] 
ICH Core          [1.100    ]...................[ 1.100   ] 

DRAM Voltage      [1.800    ]...................[ 2.060    ] Tried ~ 2.100
DRAM Termination  [0.900    ]...................[ Normal   ] 
Channel A Ref     [0.900    ]...................[ Normal     ] 
Channel B Ref     [0.900    ]...................[ Normal     ]  

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Enabled  ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled  ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Enabled  ]

*******Integraed Peripherals******
Legacy USB Storage Detect.......................[ Disabled  ]

Thanks!

**Touche** · 02-04-2009, 04:34 PM

Try this and then go for lower volts/timings if it's stable:

Code:

****** Gigabyte EP45 UD3P Bios F7 ******

E8500 510 X 8 4080MHz 

Robust Graphics Booster.........................[ Auto     ] 
CPU Clock Ratio.................................[ 8        ] 
Fine CPU Clock Ratio............................[ 0        ] 
CPU Frequency 4.0GHz...........................[ 510 x 8  ]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled  ] 
CPU Host Frequency (Mhz)........................[ 510      ] 
PCI Express Frequency (Mhz).....................[ 100      ] 
C.I.A 2 [Disabled] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv   ] 
PCI Express Clock Drive.........................[ 900mv   ] 
CPU Clock Skew..................................[ 0ps] 
MCH Clock Skew..................................[ 0ps     ] 

******DRAM Performance Control******

Performance Enhance.............................[ Standard ] 
Extreme Memory Profile (XMP)....................[ Disabled ] 
(G) MCH Frequency Latch.........................[ 400MHz   ] 
System Memory Multipler.........................[ 2.00D    ] 
Memory Frequency 1066...........................[ 1000      ] 
DRAM Timing Selectable..........................[ Manual   ] 

CAS Latency Time................................[ 5        ] 
tRCD............................................[ 5        ] 
tRP.............................................[ 5        ] 
tRAS............................................[ 18       ] 

******Advanced Timing Control******

tRRD............................................[ 4        ] [Auto] 
tWTR............................................[ 4        ] [Auto] 
tWR.............................................[ 8        ] [Auto] 
tRFC............................................[ 54       ] [Auto] 
tRTP............................................[ 4        ] [Auto] 
Command Rate (cmd)..............................[ 2T       ] 

******Channel A Timing Settings******     

Static tRead Value        [ 11 ] ................[ Auto    ] Try 12 also
tRD Phase0 Adjustment     [ 1 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ Auto     ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Channel B Timing Settings******     

Static tRead Value        [ 11 ] ................[ Auto    ] Try 12 also
tRD Phase0 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto     ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto     ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto     ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto     ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto     ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto     ] 

Dimm 1 Clock Skew Control.......................[ Auto     ] 
Dimm 2 Clock Skew Control.......................[ Auto     ] 
DDR Write Training..............................[ Auto     ] 

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ Auto     ] 
Data Driving Pull Up Level......................[ Auto     ] 
cmd Driving Pull Up Level.......................[ Auto     ] 
ctrl Driving Pull Up Level......................[ Auto     ]
clk Driving Pull Up Level.......................[ Auto     ]

Data Driving Pull Down Level....................[ Auto     ] 
cmd Driving Pull Down Level.....................[ Auto     ] 
ctrl Driving Pull Down Level....................[ Auto     ] 
clk Driving Pull Down Level.....................[ Auto     ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Disabled ] 
CPU Vcore         [ 1.25000 ]...................[ 1.41250 ] 
CPU Termination   [ 1.20    ]...................[ 1.30  ]
CPU PLL           [ 1.50    ]...................[ 1.5000  ]  
CPU Reference     [ 0.760   ]...................[0.823    ] 

MCH Core          [1.100    ]...................[ 1.400   ]  
MCH Reference     [0.760    ]...................[ 0.783     ] Try 0.783-0.823 + step or two up
MCH/DRAM Refernce [0.900    ]...................[ 1.100     ] 
ICH I/O           [1.500    ]...................[ 1.500     ] 
ICH Core          [1.100    ]...................[ 1.100   ] 

DRAM Voltage      [1.800    ]...................[ 2.200    ] 
DRAM Termination  [0.900    ]...................[1.100   ] 
Channel A Ref     [0.900    ]...................[ 1.100      ] 
Channel B Ref     [0.900    ]...................[ 1.100      ]

**neo mike** · 02-04-2009, 04:39 PM

Why does everybody run there memory 1:1 here ? does the 333, 266 strap work on this board ? maybe tough with a quad, but not with dual core, 1:1 totally stinks, it kills your memory bandwidth.

**Touche** · 02-04-2009, 04:47 PM

Originally Posted by neo mike

Why does everybody run there memory 1:1 here ? does the 333, 266 strap work on this board ? maybe tough with a quad, but not with dual core, 1:1 totally stinks, it kills your memory bandwidth.

Not everyone has memory capable of >1000 MHz. Besides, memory bandwidth is not at all important for Core architecture in real life applications.

Originally Posted by Phunky Phish

Anyone help me tweek these? It runs stable but I leave it in suspend (S3) and when I restarted today it went into a boot cycle.

It's a known issue with these boards. We're still waiting for a fix.

**radaja** · 02-04-2009, 04:55 PM

for me its mainly cause i was having trouble running 5:6 but i got it going but noticed that the clocks i was able to achieve with 5:6,my everest scores were not that much higher than when i ran 1:1.and since i have recently bought a second set of g.skill pc-8800's i figured using 8 gigs at these clocks would be just as good(with lower v dimm).so far it performs very well at 510x8.5 w/8gigs.but now ive noticed that im able to run this clock with the 8gigs at the same volts as with 2gigs,so im might just try 2gigs again running 5:6 and see how far i can push this 9650 now that im getting the hang of it.BY THE WAY-i got a brand new maximus II for my replacement from asus(finally).only took four boards from asus+the original that i bought so i guess 5 is the new lucky number 3.ill be selling it if anyone is interested.not looking to make all my money back,just want to wipe my hands of this ordeal,so it will be cheap.pm me if you interested

**SpeedEuphoria** · 02-04-2009, 05:27 PM

Originally Posted by xbiusx

But blend test gave error before 1min, so there is some wrong with my settings about the memory.

Its likely MCH ref or even MCH core that is holding you back. Run memtest and loop test #7. If you see tons of errors, raise the MCH core or even raise PL(static tRead) or your mem timings. If you get 1-2 errors in each pass then change the mch reff.

I just got my Q9650

, So far I need different MCH ref settings and likely cpu reff settings for sure. I dont have much time tonight but will be looking back through this thread to try some settings.

**neo mike** · 02-04-2009, 05:39 PM

Hopefully they will fix this issue with the straps, and yes memory bandwidth does matter in everyday use. Im curious what kind of temps you guys are getting on the northbridge ? does this board run hot on nb ?

**Touche** · 02-04-2009, 06:09 PM

Originally Posted by neo mike

Hopefully they will fix this issue with the straps, and yes memory bandwidth does matter in everyday use.

Any benchmarks?

http://www.xbitlabs.com/articles/mem...ory-guide.html

**nugzo** · 02-04-2009, 06:13 PM

Originally Posted by radaja

hey nugzo.what are your bios settings for your 4400 9x490 run?if you could post them it would appreciated,i would like to see if i can get 4400 too.thanks

Originally Posted by Jor3lBR

Radaja I think he uses my template:

http://www.xtremesystems.org/forums/...postcount=1308

I am using that exact template. Ony things different are 490fsb instead of 489 and Memory is 400 2.00D 1:1 for 980mhz for the 8gb. Bandwith is good enough for me. Temps are good under load since i replaced the TRUE with a water loop. F7 bios. This is my 24/7 setup. It gets me 22000 on 3dmark06 and 23000 on Vantage.

**radaja** · 02-04-2009, 06:22 PM

nugzo,very nice .thanks for the info

**SpeedEuphoria** · 02-04-2009, 09:17 PM

Hey I just poped in my Q9650, used Jor3lBR's template and on air I go easily. Clocks just as good if not better than my E8400 E0, just hotter, haven't even let the AS5 settle yet.

1st testing done, booted right up. On to stability now.
1M Spi

32M Spi

I'm sure I can lower the voltage or clock higher this is 1st test!!

Edit: it failed after 30min of OCCT, so on to tweaking, lol.

What's the scoop on removing the "Gigabyte" and "Ultra Durable" covers from the MCH and PWM covers?? As I know that my northbridge is running much hotter than ET6 reports. I thought I saw a couple degree's cooler?

**fatguy1992** · 02-04-2009, 09:34 PM

Nice work SpeedEuphoria

Good luck.

**nugzo** · 02-04-2009, 10:32 PM

Originally Posted by SpeedEuphoria

Hey I just poped in my Q9650, used Jor3lBR's template and on air I go easily. Clocks just as good if not better than my E8400 E0, just hotter, haven't even let the AS5 settle yet.

1st testing done, booted right up. On to stability now.

I'm sure I can lower the voltage or clock higher this is 1st test!!

What's the scoop on removing the "Gigabyte" and "Ultra Durable" covers from the MCH and PWM covers?? As I know that my northbridge is running much hotter than ET6 reports. I thought I saw a couple degree's cooler?

Nice work. I'm using the same template.

Taking the cover off the NB should help a lot if you have a fan blowing on it. As far as i know, there is no NB Temp sensor on this board. Not sure what your seeing in ET6.

**fatguy1992** · 02-04-2009, 10:44 PM

Everest and ET6 both report NB temps, but they are different

Also whats the max safe NB temp?

**spawn447** · 02-04-2009, 10:50 PM

hi, first post on XS . couldn't find the "welcome to the forum " post so i guess just dive in ?

ive been following these threads for a while , right after i bought a Q9650 that is.

guess what happened next ? I ended up building another pc instead of upgrading the one i already have, lol.

need a little advice on my setup, btw thanks for the bios templates guys !!!

Q9650 L826A965
9 x 423 for 3.8 , max temp with IBT 1.9 = 61c
cpu @ 1.25625v bios / 1.23 cpuz/everest

ive booted to 4.5 but it gets too hot with just prime , as soon as i see it hit 65c i stop it. cooling = TRUE (not lapped) antec 120's on high push/pull , case HAF 932. fix??? 120 x 38 fans on cooler or do you think water would get me there ? im thinking this kit : Swiftech H20-220 Apex Ultima

p.s. by there im thinking 24/7

thanks in advance .

**sean222** · 02-04-2009, 11:03 PM

Hey everyone, longgggg time lurker here, I never post! Just wanted to start by saying thanks to Jor3lBR and nugzo, your BIOS settings have helped me alot.

The Q9650 and UD3P truly were made for each other. I'm at 4.25GHz stable, but I'm pretty sure I could run this baby at 4.4 or 4.5 24/7 stable if I had better watercooling. I just have a crappy rad (MCR220). I should've gotten the Thermochill or Faser '3 fan' rad

Oh well.

No success running 509+ FSB at a lower multi

Best I got at a lower multi was 508x8.5, but I think I like 473x9 better. Let's me run my Dominator's at SIGNIFICANTLY better timings.

I'm Prime95, OCCT, and Orthos Stable...but I fail IBT instantly, IBT gets my CPU wayyyy too hot (75C+). I doubt anything I'll ever run will get my CPU that hot so I'm ok with failing that.

Also, thanks to EVERYONE in this thread because it wasn't just nugzo and Jor3lBR that helped me, it was comments posted by many different people in this thread and in nugzo's other UD3 thread.

Good luck to everyone and I hope you can acheive a good stable clock like I have, it's a good feeling!

Screenshot:

My Baby:

Here are my BIOS settings:

Code:

****** Gigabyte EP45 UD3P Bios F7 ******

Robust Graphics Booster.........................[ Auto ] 
CPU Clock Ratio.................................[ 9 ] 
Fine CPU Clock Ratio............................[ 0 ] 

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled  ] 
CPU Host Frequency (Mhz)........................[ 473 ] 
PCI Express Frequency (Mhz).....................[ 100 ] 
C.I.A 2.........................................[ Disabled ] 

******Advanced Clock Control******

CPU Clock Drive.................................[ 1000mv ] 
PCI Express Clock Drive.........................[ 1000mv ] 
CPU Clock Skew..................................[ 0ps ] 
MCH Clock Skew..................................[ 0ps ] 

******DRAM Performance Control******

Performance Enhance.............................[ Standard ] 
Extreme Memory Profile (XMP)....................[ Disabled ] 
(G) MCH Frequency Latch.........................[ 400MHz ] 
System Memory Multipler.........................[ 2.00D ] 
Memory Frequency 1066...........................[ 946 ] 
DRAM Timing Selectable..........................[ Manual ] 

CAS Latency Time................................[ 5  ] 
tRCD............................................[ 5  ] 
tRP.............................................[ 4  ] 
tRAS............................................[ 12 ] 

******Advanced Timing Control******

tRRD............................................[ 3  ] 
tWTR............................................[ 4  ] 
tWR.............................................[ 6  ] 
tRFC............................................[ 55 ] 
tRTP............................................[ 4  ] 
Command Rate (cmd)..............................[ 2T ] 

******Channel A Timing Settings******     

Static tRead Value        [ 11 ] ...............[ 9 ] 
tRD Phase0 Adjustment     [ 1 ] ................[ Auto ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ] 

Dimm 1 Clock Skew Control.......................[ Auto ] 
Dimm 2 Clock Skew Control.......................[ Auto ] 
DDR Write Training..............................[ Auto ] 

******Channel A Driving Settings****** 

Drive Strength Profile..........................[ Auto ] 
Data Driving Pull Up Level......................[ Auto ] 
cmd Driving Pull Up Level.......................[ Auto ] 
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ] 
cmd Driving Pull Down Level.....................[ Auto ] 
ctrl Driving Pull Down Level....................[ Auto ] 
clk Driving Pull Down Level.....................[ Auto ]

******Channel B Timing Settings******     

Static tRead Value        [ 11 ] ...............[ 9 ] 
tRD Phase0 Adjustment     [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment     [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment     [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment     [ 0 ] ................[ Auto ] 

tRD 2rd (Differnt Rank)   [ 8 ] ................[ Auto ]
tWR 2wr (Differnt Rank)   [ 8 ] ................[ Auto ] 
tWR 2rd (Differnt Rank)   [ 7 ] ................[ Auto ] 
tRD 2wr (Same/Difft Rank) [ 9 ] ................[ Auto ] 

Dimm 1 Clock Skew Control.......................[ Auto ] 
Dimm 2 Clock Skew Control.......................[ Auto ] 
DDR Write Training..............................[ Auto ] 

******Channel B Driving Settings****** 

Drive Strength Profile..........................[ Auto ] 
Data Driving Pull Up Level......................[ Auto ] 
cmd Driving Pull Up Level.......................[ Auto ] 
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]

Data Driving Pull Down Level....................[ Auto ] 
cmd Driving Pull Down Level.....................[ Auto ] 
ctrl Driving Pull Down Level....................[ Auto ] 
clk Driving Pull Down Level.....................[ Auto ]

******Motherboard Voltage Control******

Load-Line Calibration...........................[ Enabled ] 
CPU Vcore         [ 1.25000 ]...................[ 1.4000 ] 
CPU Termination   [ 1.20    ]...................[ 1.42 ]
CPU PLL           [ 1.50    ]...................[ 1.59 ]  
CPU Reference     [ 0.760   ]...................[ 0.939 ] 

MCH Core          [1.100    ]...................[ 1.42 ]  
MCH Reference     [0.760    ]...................[ 0.939 ]
MCH/DRAM Reference [0.900    ]..................[ 1.11 ] 
ICH I/O           [1.500    ]...................[ 1.57 ] 
ICH Core          [1.100    ]...................[ 1.2 ] 

DRAM Voltage      [1.800    ]...................[ 2.2 ] 
DRAM Termination  [0.900    ]...................[ Auto ] 
Channel A Ref     [0.900    ]...................[ Auto ] 
Channel B Ref     [0.900    ]...................[ Auto ]  

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ] 
No-Execute memory Protect.......................[ Enabled ]  
CPU Enhance Halt (CIE)..........................[ Disabled ]  
C2/C2E State Support............................[ Disabled ]  
C4/C4E State Support............................[ Disabled ] 
CPU Thermal Monitor.............................[ Disabled ] 
CPU EIST Function...............................[ Disabled ] 
Virtualization Technology.......................[ Disabled ]

*******Integraed Peripherals******
Legacy USB Storage Detect.......................[ Enabled ]

**redrumy3** · 02-04-2009, 11:16 PM

I Just got my board today its rev 1.1 with F6 Bios, I have Q6600, 8GB Gskill DDR2-1000 should i update bios to F7?

Also anyone with Q6600 and this board post bios setting they are using im looking through pages atm so if someone has it already and can post fast i would appreciate that

**Phunky Phish** · 02-04-2009, 11:58 PM

Hey
Anyone had a chance to look over my settings on page 72 #1799 ?

Its the big post as I dont know how to use frames!

Cheers guys, I just need a little help

**redrumy3** · 02-05-2009, 12:13 AM

hmm right now im trying 3.6ghz on Q6600 i know i can do it just trying different voltage, now is Load-Line Calibration bad to have on enabled?

**asap** · 02-05-2009, 12:34 AM

Originally Posted by fatguy1992

Everest and ET6 both report NB temps, but they are different

sorry fatguy, but where can i find on ET6 or everest?

**fatguy1992** · 02-05-2009, 12:58 AM

ET6 is easy tune 6 it comes with the mobo and just google "download everest" and download a trail of the latest version.

**fatguy1992** · 02-05-2009, 01:13 AM

Originally Posted by redrumy3

hmm right now im trying 3.6ghz on Q6600 i know i can do it just trying different voltage, now is Load-Line Calibration bad to have on enabled?

Heres my template for a Q6600 on a UD3P.

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto 
CPU Clock Ratio .......................: 9 
CPU Frequency .........................: 3.6GHz (400X9)

Clock Chip Control 

Standard Clock Control

CPU Host Clock Control.................: [Enabled] 
CPU Host Frequency (Mhz) ..............: 400 
PCI Express Frequency (Mhz) ...........: 100 
C.I.A.2 ...............................: [Disabled] 

Advanced Clock Control

CPU Clock Drive........................: Default
PCI Express Clock Drive................: Default
CPU Clock Skew (ps)....................: 0ps 
MCH Clock Skew (ps)....................: 0ps 

DRAM Performance Control

Performance Enhance....................: Standard
Extreme Memory Profile (X.M.P.)........: Disabled 
(G)MCH Frequency Latch.................: 400MHz 
System Memory Multiplier ..............: 2.0D 
Memory Frequency (Mhz) ................: 800MHz

DRAM Timing Selectable ................:  

Standard Timing Control

CAS Latency Time.......................: 5 
tRCD ..................................: 5 
tRP'...................................: 5 
tRAS...................................: 15 

Advanced Timing Control

Everything In Advanced Timing Control on auto.  

Motherboard Voltage Control

CPU

Load-Line Calibration..................: [Enabled] 
CPU Vcore..............................: 1.45
CPU Termination........................: 1.3V
CPU PLL................................: 1.50V
CPU Reference..........................: 0.823 to 0.863 

MCH/ICH

MCH Core...............................: 1.2V  
Reference..........................: 0.823 to 0.863
MCH/DRAM Ref...........................: 1.0v
ICH I/O................................: 1.5V 
ICH Core...............................: 1.100V 

DRAM
DRAM Voltage...........................: 2.0v
DRAM Termination ......................: 1.0v 
Channel A Reference....................: 1.0v
Channel B Reference ...................: 1.0v

Let me know if that works.

**redrumy3** · 02-05-2009, 01:51 AM

Originally Posted by fatguy1992

Heres my template for a Q6600 on a UD3P.

Code:

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto 
CPU Clock Ratio .......................: 9 
CPU Frequency .........................: 3.6GHz (400X9)

Clock Chip Control 

Standard Clock Control

CPU Host Clock Control.................: [Enabled] 
CPU Host Frequency (Mhz) ..............: 400 
PCI Express Frequency (Mhz) ...........: 100 
C.I.A.2 ...............................: [Disabled] 

Advanced Clock Control

CPU Clock Drive........................: Default
PCI Express Clock Drive................: Default
CPU Clock Skew (ps)....................: 0ps 
MCH Clock Skew (ps)....................: 0ps 

DRAM Performance Control

Performance Enhance....................: Standard
Extreme Memory Profile (X.M.P.)........: Disabled 
(G)MCH Frequency Latch.................: 400MHz 
System Memory Multiplier ..............: 2.0D 
Memory Frequency (Mhz) ................: 800MHz

DRAM Timing Selectable ................:  

Standard Timing Control

CAS Latency Time.......................: 5 
tRCD ..................................: 5 
tRP'...................................: 5 
tRAS...................................: 15 

Advanced Timing Control

Everything In Advanced Timing Control on auto.  

Motherboard Voltage Control

CPU

Load-Line Calibration..................: [Enabled] 
CPU Vcore..............................: 1.45
CPU Termination........................: 1.3V
CPU PLL................................: 1.50V
CPU Reference..........................: 0.823 to 0.863 

MCH/ICH

MCH Core...............................: 1.2V  
Reference..........................: 0.823 to 0.863
MCH/DRAM Ref...........................: 1.0v
ICH I/O................................: 1.5V 
ICH Core...............................: 1.100V 

DRAM
DRAM Voltage...........................: 2.0v
DRAM Termination ......................: 1.0v 
Channel A Reference....................: 1.0v
Channel B Reference ...................: 1.0v

Let me know if that works.

awesome, going to give it a try now, i know i can do 3.6 did it on ip35 but this board bios is really different :P
thanks

**Touche** · 02-05-2009, 02:09 AM

Originally Posted by redrumy3

hmm right now im trying 3.6ghz on Q6600 i know i can do it just trying different voltage, now is Load-Line Calibration bad to have on enabled?

Better to leave it disabled if you can.

Originally Posted by Phunky Phish

Hey
Anyone had a chance to look over my settings on page 72?

Its the big post as I dont know how to use frames!

Cheers guys, I just need a little help

I've answered that one. As for the temperatures, many new Core 2 CPUs have stuck sensors up until certain temp. You can use Tcase temp instead (HWMonitor, OCCT, Everest...).

**punx223** · 02-05-2009, 02:14 AM

i have an e8600 well capable of excess of 5.9ghz....

what bios is best for 24/7 and which is best for high fsb?? i havent checked out all the bios, and was wondering id one was better as i am presently on F5

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

why

ok

Finally Stable!

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: ** Official ** Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P

Thread Tools

Search Thread

Rate This Thread

Display

why

ok

Finally Stable!

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

Thread: Official Gigabyte UD3 P45 Series -- EP45-UD3 / EP45-UD3R / EP45-UD3P