^^Thanks for the encouragement, I'll keep pushing and let you know how it goes
^^Thanks for the encouragement, I'll keep pushing and let you know how it goes
P95 failed after 1hr 15min. Raised the vcore from 1.280 to 1.296 and trying again...
Hi everyone , today I tried to set 8x565 but it was impossible for me , so I need some help, if someone can post BIOS settings for 8x565. My CPU is 8600 (Q822A444), MB MIIF and 4GB Corsair Dominator 1:1(1130). I need a point to start pls help.
Q9650 CPU @ 4.410GHz (9*490) | ASUS Maximus II Formula | 2*2GB OCZ Blade LV 1200, 5-5-5-15@1230Mhz | 750GB Hitachi | ASUS 9800GTX+ (850/1300/2000) | Water cooled Coolermaster Cosmos S & Hiper 670W | NEC MultiSync® 20WGX2Pro
I have used the supplied Asus fan on the PWM beside the back panel which also helps cool the NB thanks to the heat pipe and the psu fan is sucking air over the other set which has a huge heatsink on it so I really dont think it would be worthwhile to watercool them. Asus knew this board would get watercooled, they even collaborated with Swiftech to produce a NB block just for it http://www.performance-pcs.com/catal...ducts_id=24408Originally Posted by CryptiK
Nevin, best place to start is the guide Simps wrote I think. http://www.xtremesystems.org/forums/...postcount=2718
dx58so
w3520@4100
4x1gb corsair ddr3-1333
gtx 295
TR ultra-x, 2 scythe ultrakaze push/pull
xclio stablepower 1000
vista ultimate
[SIGPIC][/SIGPIC]
-------------------------------
would you crunch if you thought it would save her life?
maybe it will!
This is my setting for the E8400 (Stable)
I will be getting the Q9650 soon
I would like to know if I can use the same setting or where to modify
Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : AUTO
CPU Ratio Control : Manual
- Ratio CMOS Setting : 9
FSB Frequency : 450
CPU Clock Skew : Normal
North Bridge Clock Skew : Normal
FSB Strap to North Bridge : Auto
DRAM Frequency: DDR2-850 MHz
Dram Clock Skew CH1 A1 : Normal
DRAM Clock Skew CH1 A2 : Normal
Dram Clock Skew CH1 B1 : Normal
Dram Clock Skew CH1 B2 : Normal
DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : 5
Row Refresh Cycle Time : 60
Write Recovery Time : 8
Read to Precharge Time : 5
Read to Write Delay (S/D) : Auto
Write to Read Delay (S) : Auto
Write to Read Delay (D) : Auto
Read to Read Delay (S) : Auto
Read to Read Delay (D) : Auto
Write to Write Delay (S) : Auto
Write to Write Delay (D) : Auto
Write to PRE Delay : Auto
Read to PRE Delay : Auto
PRE to PRE Delay : Auto
ALL PRE to ACT Delay : Auto
ALL PRE to REF Delay : Auto
DRAM Static Read Control: disabled
Dram Read Training : disabled
MEM OC Charger : disabled
Ai Clock Twister : Moderate
Transaction Booster : Manual
Common Performance Level: 10
Pull-In of CHA PH1 Disabled
Pull-In of CHA PH2 Disabled
Pull-In of CHA PH3 Disabled
Pull-In of CHA PH4 Disabled
Pull-In of CHA PH5 Disabled
Pull-In of CHB PH1 Disabled
Pull-In of CHB PH2 Disabled
Pull-In of CHB PH3 Disabled
Pull-In of CHB PH4 Disabled
Pull-In of CHB PH5 Disabled
PCIE Frequency : 100
CPU Voltage : 1.36250v
CPU PLL Voltage : 1.51325v
FSBT : 1.2v
DRAM Voltage : 2.1v
North Bridge Voltage : 1.32525v
South Bridge Voltage 1.5 : 1.5
South Bridge Voltage 1.1 : 1.1
CPU GTL Reference 0 : Auto
CPU GTL Reference 1 : Auto
CPU GTL Reference 2 : Auto
CPU GTL Reference 3 : Auto
North Bridge GTL Reference : AUTO
DDR2 Channel A REF Voltage : AUTO
DDR2 Channel B REF Voltage : AUTO
North Bridge DDR Reference : AUTO
Load Line Calabration : Enabled
CPU Sread Spectrum : Disabled
PCIE Spread Spectrum : Disabled
CPU Configuration:
Ratio CMOS Setting: 9
C1E Support: Disabled
Max CPUID Value Limit: Disabled
Intel Virtualization Tech: Enable
CPU TM Function: Disabled
Execute Disable Bit: Enabled
Load-Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
Rich Martin
Spec:
Q9650 @ 4050 MHz @ 1.29v
Maximus II , P45 chipset
GeForce GTX 260
Corsair XMS2 DHX DDR2PC6400 (4 GB)
(2) Seagate 320 RAID 0, (2) 1TB SATA II
PS. Corsair VX550W
Cooling Master ATCS 840
Windows Vista Ultimate x64
Cooling: Swiftech H20-220 Apex Ultra
Using only 1.22v-1.24v now and trying to get cpu 24/7 stable @ 3.9ghz...
How do I change the VTT voltage?
Last edited by Celcius; 01-27-2009 at 01:38 PM.
Go with Simp's guide - it covers everything basically and even if it would not get u where u want while proceeding with it you will learn all the voltages and how to adjust them (options too) so u can make your adjustments knowing what r u doing.
And if u insist on quick quide:
1. Test highest or target stable ram clock - with mem test 2.1. (u know ram is not a problem)
2. Test target cpu speed with P95 Small ftt. (u know cpu can make it)
3. Test MOBO at target FSB and CPU and RAM with IBT or linx as starter 10 loops and for finall stability 12h+ with P95 blend.
At point 3 u will see what for is vtt :P and GTLs.
But just use Simps guide it is detailed and really good starter.
GL and HF m8
q9550 e0 (lapped) - 3.98@1.326v - True Black (lapped + washer mod) + 2x NF-P12
MF2 - 1802 (washer mod), 2x2 8500 Dominator @1115, Corsair HX 850w
BFG 216 OCX 710/1480/1240 Acer 2216w, Samsung 40" 1080p,
Antec P180 + 3x NF-P12, 1TB WD Black + 3x 500GB WD AAKS
ASUS Xonar D2
eSATA.....
Anyone getting this to work in Windows XP Pro?
I loaded Marvel SATA driver and that completely wracked the system even causing my DVD drive to disappear. Now it is uninstalled. I do have Marvell controller IDE/esata enabled in BIOS.
I am trying to get the Thermaltake BlacX USB & eSATA docking station to work with eSATA. USB works well. Any help?
Post Edit
You should not start a new cpu OC at 4Ghz. At that point there may be multiple problems and if so getting it stable will be a nightmare. You need to work up from a lower point (preferably stock speed with all stock voltages for board/ram/cpu) and find what settings you need to increase and alter along the way.
Start with the ram 1:1 and PL10, later you can try and find what the best divider is for your ram at the FSB you end up at.
Last edited by CryptiK; 01-28-2009 at 06:55 AM.
Ci7 990X::Rampage III Extreme::12GB Corsair Dominator 1866C7GT::2 x EVGA SC Titans in SLI::Corsair AX1200::TJ07::Watercooled
Ci7 920 3849B018::Rampage II Extreme::6GB GSKILL Trident 2000C9 BBSE::EVGA GTX580::Antec Signature SG850::TJ09::Aircooled w/TRUE 120X
grnfinger,is this the WC kit you were talking about?it looks like it has the right block. http://www.coolerguys.com/840556020998.html
_________________________________________________
............................ImAcOmPuTeRsPoNgE............................
[SIGPIC][/SIGPIC]
MY HEATWARE 76-0-0
If you change your NB strap do you have to change your GTL Ref's again?
You mean NB GTL Ref? Not sure really, I choose strap/ram speed etc then tune NB GTL. NB GTL is mostly dependent on FSB and ram speed/timings, but strap can theoretically affect it. Also testing NB GTL Ref using games is also important. You can be stress test stable and crash out of games in seconds/minutes if your NB GTL Ref is not correct.
Ci7 990X::Rampage III Extreme::12GB Corsair Dominator 1866C7GT::2 x EVGA SC Titans in SLI::Corsair AX1200::TJ07::Watercooled
Ci7 920 3849B018::Rampage II Extreme::6GB GSKILL Trident 2000C9 BBSE::EVGA GTX580::Antec Signature SG850::TJ09::Aircooled w/TRUE 120X
Thanks
I'm looking at all the possible values on Simp's guide and noticed that the value for cores 0&2 is always higher than the value for cores 1&3. Is that always going to be true?
Also, VTT = FSB termination voltage right?
hi all.. just want to say thanks to cryptix for give me guide for the washer mode..now nb temp drop from 54c to 34c..so happy coz just litle bit work as easy 123 then the temp all improve..cheer for the good guide..Looks good, the Thermaltake Extreme Spirit vers 1 and II NB/SB cooler works also
i m using tunic tx2 with properly using 1 washer each screww and 2 washer for the n/b..
this my result while oc.e86
last time oc e84..
Yes 0/2 will (usually*) be higher than 1/3 as 0/2 use use the 0.635x multi and 1/3 use the 0.667x multi, and yes, Vtt is FSB termination also denoted as vFSB).
* - you can of course set the GTL Refs to whatever you want, you could use 20/20/20/20 if it worked better for you. Dont limit yourself to a few orthodox choices. try as many combos as you can, just remember/write down what was stable so you don't get lost.
No problem glad it worked out for you. Your temps look very good now, much better than 70*C on NB. Congratulations on reaching 4500 MHz
Last edited by CryptiK; 01-28-2009 at 09:45 AM.
Ci7 990X::Rampage III Extreme::12GB Corsair Dominator 1866C7GT::2 x EVGA SC Titans in SLI::Corsair AX1200::TJ07::Watercooled
Ci7 920 3849B018::Rampage II Extreme::6GB GSKILL Trident 2000C9 BBSE::EVGA GTX580::Antec Signature SG850::TJ09::Aircooled w/TRUE 120X
Afraid I'll be resigning from the MIIF club, I got my replacement back and put it up on eBay and I have a bid. Wish I could say it was fun while it lasted.
when doing the GTL's, is "auto" the same thing as 0mV? i want to set it to +40 for core 0/2 and zero for core 1/3, but there's only choices for -5mV and +10mV with nothing in between.
[SIGPIC][/SIGPIC]
Yes sir thats the one, its a great all in one kit for first timers, and lots of room for upgrades, but really the only upgrade for that kit will be bigger better rad later on
grnfinger,thanks,there is the same kit but the plus version the only difference is the gpu block added for 100 extra,i think i might get that one.
_________________________________________________
............................ImAcOmPuTeRsPoNgE............................
[SIGPIC][/SIGPIC]
MY HEATWARE 76-0-0
Good luck with the sale. Hope you have better experiences with other boards.
Yes 'auto' is the same as '0mv'
Ci7 990X::Rampage III Extreme::12GB Corsair Dominator 1866C7GT::2 x EVGA SC Titans in SLI::Corsair AX1200::TJ07::Watercooled
Ci7 920 3849B018::Rampage II Extreme::6GB GSKILL Trident 2000C9 BBSE::EVGA GTX580::Antec Signature SG850::TJ09::Aircooled w/TRUE 120X
I'm having a lot of fun with my Gigabyte UD3P, and I may get a DFI UT P45 at some point. Of course now that I'm getting rid of my MIIF, I'm sure Asus will release some super BIOS update that fixes all the problems and turns it into a monster memory overclocker
it doubt it.if they havent done it by now,i fear they may never get around to it.im sure theyre working on the latest stuff now.but hope is always a good thing.its what keeps us moving forward in life.
_________________________________________________
............................ImAcOmPuTeRsPoNgE............................
[SIGPIC][/SIGPIC]
MY HEATWARE 76-0-0
After alot of tweaking, This board just refuses 500FSB. I had 490 stable for an hour than it did the same crash as 500FSB, so 485x8.5 is AWESOME.
I used the NB GTL at +30 thanks to Simps, which got it solid no problem. then i put my CPU GTL to +20/-20/+20/-20 which got me 4.144Ghz with 1 NOTCH OF VCORE BUMP!!! I went from 1.3875 @ 450x9 (4.05Ghz) to 485x8.5 (4.14Ghz) with 1.39175!
Amazing. but i tried all GTL differences and 500FSB is a no go, 490 is possible but meh. This is fast.
My memory is slacking now though, currently using 400Mhz strap @ 970 1:1 with the ram, but im getting 1150 ram and i can use the 333 strap and set it to 1177.
Cant wait.
Asus Rampage II Extreme
Intel i7-920 @ 4.2Ghz w/ HT
6GB G.Skill @ 1600Mhz
eVGA / MSI GTX480 SLI
Corsair HX1000w
CoolerMaster HAF932 OG
Corsair H70
the last time i tried esata, it just ruined my windows install.
do you have to plug it all in, then turn the power on?
also, will the speedinghdd ports handle 2 seperate drives not in any raid mode?
i wanna swap back to single drives instead of raid-0, but like the fact that its on a pcie lane rather than the useless pci bottlenecked bus.
Reply With Quote
Bookmarks