Live MB OC Report :: ASUS Rampage Extreme

[Gullo92]

can you help me with overclocking??. i have rampage extreme(with bios 1003) intel q9550 corsair dominator 1800 mhz 2n 2.00V 7 7 7 20(my ram haven't xmp function). help me please. can you post settings with my setup? excuse me for my english i'm italian. this is the settings of rob2k he is a qx9770( in this overclock have multi 8.5 q9550 have multi 8.5) rampage extreme and my ram.

475 settings - BIOS 1003

Extreme Tweaker

Ai Overclock Tuner: Manual
OC From Memory Level Up: Auto
FSB Frequency: 475
CPU Ratio Setting: 8.5

CPU Configuration

CPU Ratio Setting: 8.5
C1E Support: Disabled
CPU TM Function: Enabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled

CPU Clock Skew: Delay 300ps
NB Clock Skew: Delay 200ps
FSB Strap to North Bridge: 400
PCIE Frequency: 101
DRAM Frequency: 1900
DRAM Command Rate: 1N
DRAM Timing Control: Manual
1st Information: 7-7-7-21-8-88-12-6 (7-6-6-20 @ 472)
CAS# Latency: 7
RAS# to CAS# Delay: 7
RAS# Pre Time: 7
RAS# ACT Time: 21
RAS# To RAS# Delay: 8
REF Cycle Time: 88
WRITE Recovery Time: 12
READ to Pre Time: 6
2nd Information : 8-7-6-4-7-4-7
READ to WRITE Delay (S/D): 8
WRITE to READ Delay (S): 7
WRITE to READ Delay (D): 6
READ to READ (S): 4
READ to READ (D): 7
WRITE to WRITE (S): 4
WRITE to WRITE (D): 7
3RD Information: 23-8-1-8-8
WRITE to PRE Delay: 23
READ to PRE Delay: 8
PRE to PRE Delay: 1
ALL PRE to ACT Delay: 8
ALL PRE to REF Delay: 8
DRAM Static Read Control: Disabled
DRAM Dynamic Write Control: Disabled

DRAM Skew Control

DRAM CMD Skew on Channel A: Delay 75ps
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Delay 150ps
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto


Ai Clock Twister: Auto
Ai Transaction Booster: Auto
Common Performance Level: 06 (Auto selected)

EPU II Phase Control: Auto
CPU Voltage: 1.468
Load-Line Calibration: Disabled
CPU PLL Voltage: 1.577
FSB Termination Voltage: 1.418
CPU GTLVerf (0): +50mv
CPU GTLVerf (1): +50mv
CPU GTLVerf (2): +50mv
CPU GTLVerf (3): +50mv
NB GTLVerf: +60mV
North Bridge Voltage: 1.630
DRAM Voltage: 2.05
NB DDRVref: AUTO
DDR3 ChannelA Vref: +12.5mv
DDR3 ChannelB Vref: +12.5mv
South Bridge 1.5 Voltage: 1.577
South Bridge 1.05 Voltage: 1.086
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled


other settings in to bios are default

i have tried with 472 fsb and 475 fsb but the ram is unstable help me!!!