Live MB OC Report :: ASUS Rampage Extreme

[cheapseats]

......Retest with orthos in diagnostic mode
Set to blend.. and then custom min fft 4096 max 4096 priority 10.
try to pass more than 4 hours... take note this is hard.. a lot of test that will pass memtest86/hci memtest will not pass this.........

This fails 4096k test in 1 hour max.


I've included the full settings anyway, in case anyone wants to give them a spin....

worth a bit more work though as 200strap/tRD6 (above 475FSB) gives reasonable performance for CL8.
All other straps are slower with CL8/1:2 at 500FSB.



500x9 / 1000mhz / 200 strap / CL8 / tRD 6 / CT Strong




thanks cstkl1 for the GTL, IBT stability is better than with my GTL

AI OVERCLOCK TUNER =========================MANUAL
OC FROM CPU LEVEL ==========================AUTO
OC FROM MEMORY LEVEL UP ====================AUTO
FSB FREQUENCY ==============================500
CPU RATIO SETTING ==========================09

CPU CLOCK SKEW =============================AUTO
NB CLOCK SKEW ==============================AUTO
FSB STRAP TO NORTH BRIDGE ==================200
PCIE FREQUENCY =============================101
DRAM FREQUENCY =============================2000
DRAM COMAND RATE ===========================1N
DRAM TIMING CONTROL ========================MANUAL
CAS LATENCY ================================8
RAS TO CAS DELAY ===========================8
RAS PRE TIME ===============================8
RAS ACT TIME ===============================24
RAS TO RAS DELAY ===========================AUTO
REF CYCLE TIME =============================AUTO
WRITE RECOVERY TIME ========================AUTO
READ TO PRE TIME ===========================AUTO
READ TO WRITE DELAY S/D ====================AUTO
WRITE TO READ DELAY S ======================AUTO
WRITE TO READ DELAY D ======================AUTO
READ TO READ DELAY S =======================AUTO
READ TO READ DELAY D =======================AUTO
WRITE TO WRITE DELAY S =====================AUTO
WRITE TO WRITE DELAY D =====================AUTO
WRITE TO PRE DELAY =========================AUTO
READ TO PRE DELAY ==========================AUTO
PRE TO PRE DELAY ===========================AUTO
ALL PRE TO ACT DELAY =======================AUTO
ALL PRE TO REF DELAY =======================AUTO
DRAM STATIC READ CONTROL ===================AUTO
DRAM DYNAMIC WRITE CONTROL =================AUTO

DRAM SKEW CONTROL
DRAM CMD SKEW ON CHANNEL A = AUTO
DRAM CLK SKEW ON DIMM A1 = AUTO
DRAM CLK SKEW ON DIMM A2 = AUTO
DRAM CTL SKEW ON DIMM A1 = AUTO
DRAM CTL SKEW ON DIMM A2 = AUTO

DRAM CMD SKEW ON CHANNEL B = AUTO
DRAM CLK SKEW ON DIMM B1 = AUTO
DRAM CLK SKEW ON DIMM B2 = AUTO
DRAM CTL SKEW ON DIMM B1 = AUTO
DRAM CTL SKEW ON DIMM B2 = AUTO


AI CLOCK TWISTER ===========================STRONG
AI TRANSACTION BOOSTER =====================MANUAL
PERFORMANCE LEVEL ==========================06

PULL-IN OF CHA PH1 =========================DISABLED
PULL-IN OF CHA PH2 =========================DISABLED
PULL-IN OF CHA PH3 =========================DISABLED
PULL-IN OF CHA PH4 =========================DISABLED
PULL-IN OF CHA PH5 =========================DISABLED
PULL-IN OF CHB PH1 =========================DISABLED
PULL-IN OF CHB PH2 =========================DISABLED
PULL-IN OF CHB PH3 =========================DISABLED
PULL-IN OF CHB PH4 =========================DISABLED
PULL-IN OF CHB PH5 =========================DISABLED

EPU II PHASE CONTROL =======================AUTO
CPU VOLTAGE ================================1.375 
LOAD-LINE CALIBRATION ======================ENABLED
CPU PLL VOLTAGE  ===========================1.617 
FSB TERMINATION VOLTAGE  ===================1.391 
CPU GTLVREF 0 ============================== +40
CPU GTLVREF 1 ==============================AUTO
CPU GTLVREF 2 ==============================AUTO
CPU GTLVREF 3 ==============================AUTO
NB GTLVREF =================================AUTO
NORTH BRIDGE VOLTAGE =======================1.603 
DRAM VOLTAGE ===============================1.908 
NB DDRVREF ================================= +12.5
DDR3 CHANNEL A VREF ======================== +12.5
DDR3 CHANNEL B VREF ======================== +12.5
SOUTH BRIDGE 1.5 VOLTAGE ===================1.617 
SOUTH BRIDGE 1.05 VOLTAGE ==================1.100
CPU SPREAD SPRECTRUM =======================DISABLED
PCIE SPREAD SPECTRUM =======================DISABLED