ok sold off my rampage 2 extreme
e8600 only
here is the super stable setup for skewing at 563fsb 1800mhz 8-8-8-24 1t 2x2gb samsung hco team xtreem pc3-16000
[/QUOTE]Code:AI OVERCLOCK TUNER =========================MANUAL OC FROM CPU LEVEL ==========================AUTO OC FROM MEMORY LEVEL UP ====================AUTO FSB FREQUENCY ==============================564 CPU RATIO SETTING ==========================7-8 CPU CLOCK SKEW =============================Delay 200 NB CLOCK SKEW ==============================Normal FSB STRAP TO NORTH BRIDGE ==================333 PCIE FREQUENCY =============================100 DRAM FREQUENCY =============================1800 DRAM COMAND RATE ===========================1N DRAM TIMING CONTROL ========================MANUAL CAS LATENCY ================================8 RAS TO CAS DELAY ===========================8 RAS PRE TIME ===============================8 RAS ACT TIME ===============================24 RAS TO RAS DELAY ===========================AUTO REF CYCLE TIME =============================72/88 WRITE RECOVERY TIME ========================AUTO READ TO PRE TIME ===========================AUTO READ TO WRITE DELAY S/D ====================AUTO WRITE TO READ DELAY S ======================AUTO WRITE TO READ DELAY D ======================AUTO READ TO READ DELAY S =======================AUTO READ TO READ DELAY D =======================AUTO WRITE TO WRITE DELAY S =====================AUTO WRITE TO WRITE DELAY D =====================AUTO WRITE TO PRE DELAY =========================AUTO READ TO PRE DELAY ==========================AUTO PRE TO PRE DELAY ===========================AUTO ALL PRE TO ACT DELAY =======================AUTO ALL PRE TO REF DELAY =======================AUTO DRAM STATIC READ CONTROL ===================AUTO DRAM DYNAMIC WRITE CONTROL =================AUTO DRAM SKEW CONTROL DRAM CMD SKEW ON CHANNEL A = Normal DRAM CLK SKEW ON DIMM A1 = Advance 125 DRAM CLK SKEW ON DIMM A2 = Advance 125 DRAM CTL SKEW ON DIMM A1 = Advance 25 DRAM CTL SKEW ON DIMM A2 = Advance 25 DRAM CMD SKEW ON CHANNEL B = Advance 50 DRAM CLK SKEW ON DIMM B1 = Advance 100 DRAM CLK SKEW ON DIMM B2 = Advance 100 DRAM CTL SKEW ON DIMM B1 = Advance 50 DRAM CTL SKEW ON DIMM B2 = Advance 50 DRAM Read/Dynamic Write = Disabled AI CLOCK TWISTER ===========================MODERATE AI TRANSACTION BOOSTER =====================MANUAL PERFORMANCE LEVEL ==========================09 PULL-IN OF CHA PH1 =========================DISABLED PULL-IN OF CHA PH2 =========================DISABLED PULL-IN OF CHA PH3 =========================DISABLED PULL-IN OF CHA PH4 =========================DISABLED PULL-IN OF CHA PH5 =========================DISABLED PULL-IN OF CHB PH1 =========================DISABLED PULL-IN OF CHB PH2 =========================DISABLED PULL-IN OF CHB PH3 =========================DISABLED PULL-IN OF CHB PH4 =========================DISABLED PULL-IN OF CHB PH5 =========================DISABLED EPU II PHASE CONTROL =======================AUTO CPU VOLTAGE ================================ LOAD-LINE CALIBRATION ======================DISABLED CPU PLL VOLTAGE ===========================1.51 FSB TERMINATION VOLTAGE ===================1.29 CPU GTLVREF 0 ==============================+40 CPU GTLVREF 1 ==============================AUTO CPU GTLVREF 2 ==============================AUTO CPU GTLVREF 3 ==============================AUTO NB GTLVREF =================================AUTO NORTH BRIDGE VOLTAGE =======================1.59 DRAM VOLTAGE ===============================1.9 NB DDRVREF =================================+12.5 DDR3 CHANNEL A VREF ========================+25 DDR3 CHANNEL B VREF ========================+25 SOUTH BRIDGE 1.5 VOLTAGE ===================1.51 SOUTH BRIDGE 1.05 VOLTAGE ==================1.06 CPU SPREAD SPRECTRUM =======================DISABLED PCIE SPREAD SPECTRUM =======================DISABLED
ram skewing
for 500fsb 1600mhz Cl7-7-7-20-1t
use same skewing except no nbdram /dram A/B = Auto, fsb termination 1.12
dram at 1.67 ....nb = 1.25v
400fsb is the same.
vtt for 563 fsb termination issue .....1.19 for IBT stable
but will fail on my test 3 for orthos .. set blend.. then custom min fft 4096... only fsb termination at 1.29 will pass.
theres other ways to force 1.19 to pass for both but will result in weird irregular issues with usb ports.
Reply With Quote
Bookmarks