ASUS Maximus II Formula - new P45 king?

[seban]

Those setting below are 2h Small FTP P95 stable but mostl core 0 and core 3 will fail blend test or linpack affter 2minutes.

Ram is memtest86 2.1 stable for about 6 passes.

If RAM and GTL set to auto in BIOS same thing with Blend test as above.

This template was found here not real adjusting done yet. Probably such fast blend failing and few hours small ftt stable is indication of something obvious - unfortunately not for me ?

Also when we are talking about safe vcore do we mean reading from CpuZ or setting in bios?

Extreme Tweaker
Ai Overclock Tuner : Manual
OC From CPU Level Up : Auto
CPU Ratio Control : Manual
- Ratio CMOS Setting : 8.5
FSB Frequency : 471
CPU Clock Skew : Auto
North Bridge Clock Skew : Auto
FSB Strap to North Bridge : Auto
DRAM Frequency: DDR2-940MHz
Dram Clock Skew CH1 A1 : Auto
DRAM Clock Skew CH1 A2 : Auto
Dram Clock Skew CH1 B1 : Auto
Dram Clock Skew CH1 B2 : Auto


DRAM Timing Control: Manual
CAS# Latency : 5
RAS# to CAS# Delay : 5
RAS# Precharge : 5
RAS# ActivateTime : 15
RAS# to RAS# Delay : 5
Row Refresh Cycle Time : 55
Write Recovery Time : 8
Read to Precharge Time : 5

Read to Write Delay (S/D) : Auto
Write to Read Delay (S) : Auto
Write to Read Delay (D) : Auto
Read to Read Delay (S) : Auto
Read to Read Delay (D) : Auto
Write to Write Delay (S) : Auto
Write to Write Delay (D) : Auto

Write to PRE Delay : Auto
Read to PRE Delay : Auto
PRE to PRE Delay : Auto
ALL PRE to ACT Delay : Auto
ALL PRE to REF Delay : Auto

DRAM Static Read Control: Disabled
Dram Read Training : Disabled
MEM OC Charger : Enabled
Ai Clock Twister : Moderate
Transaction Booster : Manual

Common Performance Level [10]

Pull-In of CHA PH1 Enabled
Pull-In of CHA PH2 Enabled
Pull-In of CHA PH3 Enabled
Pull-In of CHA PH4 Enabled
Pull-In of CHA PH5 Enabled
Pull-In of CHB PH1 Enabled
Pull-In of CHB PH2 Enabled
Pull-In of CHB PH3 Enabled
Pull-In of CHB PH4 Enabled
Pull-In of CHB PH5 Enabled

PCIE Frequency : 100

CPU Voltage : 1.35
CPU PLL Voltage : 1.53975
FSBT : 1.259
DRAM Voltage : 2.012
North Bridge Voltage : 1.35175
South Bridge Voltage 1.5 : 1.5
South Bridge Voltage 1.1 : 1.10

CPU GTL Reference 0 : +50
CPU GTL Reference 1 : +10
CPU GTL Reference 2 : +50
CPU GTL Reference 3 : +10
North Bridge GTL Reference : Auto
DDR2 Channel A REF Voltage : Auto
DDR2 Channel B REF Voltage : Auto
North Bridge DDR Reference : Auto

Load Line Calibration : Enabled
CPU Spread Spectrum : Disabled
PCIE Spread Spectrum : Disabled

Some screenie is coming.

I have planned to let this board go on air for a while now but need to know if TRUE fit vertical (push/pull) or not? Actually TRU-black!!
If not, what other great heatsink fit?

Thanks in advance!

Hi,

True black with two fans work both directions with no problem.