"ASUS P5Q Deluxe discussion".

[douirc]

I not want to go voltage highter
but P 174 and I seen the same 1.42 give 1.34
I am running now just 3712mhz
with truehighroller config but not 480 just 464
Temp carte mere 33 à 35 ° temp core 65° maxi

9654 mo/S 53 ns
Ai overlock manual
Cpu ratio 8
Fsb strap 333
Fsb freq 464 3712mhz
Pci e fre 103
Dram fre 12:10 1114mhz
Dram clk a1a2a3a4 auto
Dram timing manual

1 info 5 5 5 15 3 3 6 5 3
2 info 8 3 5 4 6 4 6
3 info 1 3 5 1 5 5

5 5 5 15 manual
ras to ras auto
row refresh auto
write recovery auto
read to precharge auto

dram static disabled
dram training disabled
mem oc enabled
aicclock twister stronger
ai transaction 8
pull in ( 10) disabled

cpu voltage 1.33125 (1.32”load”)
cpu gtl (o/2) .63
cpu gtl 1/3 .63
cpu pll v 1.56
fsb terminai 1.22
dram 2.18
nb volt 1.26
sbridge 1.2
pcie sata 1.6

load line calibre enable
cpu spread disabled
pcie spread disabled
cpu clock skew auto
nb clock skew auto
pcu margin optimi

cpu ratio 8
c1e sup disabled
all disabled

I can put a second noctua on my cpu but I must put out the asus chipset fan

somebody can me give reference à good Dissipateur Mosfet and Chipset fan to down my mb T°

I wait a new case haf 932

sorry but i have a so bad english

Hi genish...saw you've had fsb as high as 482. Any luck with 500 fsb 1:1? what were your settings?

[Dalten]

Hi guys

I have had the P5Q Deluxe for å few days now and there is something bothering me with this board.
Voltage values for VTT ,SB chipset, NB chipset and VDIMM are not showing in newest Everest Ultimate Edition (v4.60.1500).
Or in the BIOS for that matter. I can set the voltage values, but not see the result real time.

Why is this? Something Asus decided for the P5Q series or bug in BIOS? (I have the 1406 BIOS)
Do you guys have the same 'problem' as me?

What version of the board do you have? it should say on the box or a sticker on the board i think.

[Leeghoofd]

What version of the board do you have? it should say on the box or a sticker on the board i think.

There's nothing wrong with his board , there are NO readouts foreseen via bios... in fact here are not many manufacturers that have these readouts in medium range mobo's, only the MFII has this for the Asus P45 mobo's...

This is what we here all have :




Nothing more and surely nothing less

[genish]

I have going with security and "equilibre"
Temp carte mere 33 à ° temp core 71° maxi un ventilo extrac 120mm

9708 mo/S 52.5 ns
Ai overlock manual
Cpu ratio 8
Fsb strap 333
Fsb freq 475 3800mhz
Pci e fre 104
Dram fre 12:10 1141mhz
Dram clk a1a2a3a4 auto
Dram timing manual

1 info 5 5 5 15 3 3 6 5 3
2 info 8 3 5 4 6 4 6
3 info 1 3 5 1 5 5

5 5 5 15 manual
ras to ras auto
row refresh auto
write recovery auto
read to precharge auto

dram static disabled
dram training disabled
mem oc enabled
aicclock twister stronger
ai transaction 8
pull in ( 10) disabled

cpu voltage 1.40
cpu gtl (o/2) .63
cpu gtl 1/3 .63
cpu pll v 1.56
fsb terminai 1.30
dram 2.20
nb volt 1.28
sbridge 1.2
pcie sata 1.6

load line calibre enable
cpu spread disabled
pcie spread disabled
cpu clock skew auto
nb clock skew auto
pcu margin optimi

cpu ratio 8
c1e sup disabled
all disabled
I have put a 80mm over my memory led blue and red whith fan controleur " just a good sound calibration not very noise just quit"
Ai overlock manual
Cpu ratio 8
Fsb strap auto
Fsb freq 482 3856mhz
Pci e fre 103
Dram fre 12:10 1157mhz
Dram clk a1a2a3a4 auto
Dram timing manual

1 info 5 5 5 15 3 3 6 5 3
2 info 8 3 5 4 6 4 6
3 info 1 3 5 1 5 5

5 5 5 15 manual
ras to ras auto
row refresh auto
write recovery auto
read to precharge auto

dram static disabled
dram training disabled
mem oc enabled
aicclock twister moderate
ai transaction 10
pull in ( 10) disabled

cpu voltage 1.425 (1.34”load”)
cpu gtl (o/2) .63
cpu gtl 1/3 .675
cpu pll v 1.56
fsb terminai 1.30
dram 2.24
nb volt 1.38
sbridge 1.2
pcie sata auto

load line calibre enable
cpu spread disabled
pcie spread disabled
cpu clock skew 400ps
nb clock skew 400ps
pcu margin optimi

cpu ratio 8
c1e sup disabled
all disabled but cpu tm function enabled

but I think mem95 and everest and oct not give me the same T° 71° fore the core one on oct 65° with everest 61° with realtemp

[genish]

i have a haf 932 with 120mm out on the top+ 120mm in on the floor of the case
a noctua nh with a fan 120mm in a fan 120mm*20mm out
2 rh 09 for mofset a 90mm over one
2 sli/fix chipset with fans 80mm
a 4870 with o3+ with fans ( 90mm+50mm+25mm)

[Leeghoofd]

K Genish I have absolutely no clue what you want to achieve or ask, plz pm me, seems you are french ( I can express myself a bit in french)

[gazmatrix]

Hi guys,

I've now build my new system, here's the full spec:

Asus P5Q-E
Q9550, Yorkfield Core 2.83Ghz
(2x2GB) Corsair Dominator DDR2 PC2-8500 1066
XFX GTX 260 (216) Black Edition PCI-E Graphics Card
Corsair 620W HX Modular PSU - ATX12V v2.2 APFC
Coolermaster Cosmos RC-1000 Full Tower Case
Western Digital WD6400AAKS 640GB Hard Drive
Zalman CNPS 9700 LED

I've been running the system for just over a week now, and it's running very sweet... My stock 3D Mark06 score is 14302...

Anyway I want to get a nice overclock for 24/7 use, I'm aiming for 3.6GHz...

So far i've managed to get 3.0GHz which increased my 3D Mark06 score to 15210, and 3.2GHz which increased my 3D Mark06 score to 15808 these are both rock solid stable...

On the above 2 settings, I only changed the voltage for CPU to 1.2250v and the DRAM to 2.0v everything else was set to Auto...

After reading I found the board likes to over-volt when the voltages are set to auto, so for my 3.4Ghz I decided to put all the voltages in my self...

I then tried 3.4GHz which increased my 3D Mark06 score to 17048, but this failed Prime95 on work thread 1, running a Torture Test (in-place large FFTs) after 2 hours...

Here's how I set the Bios for 3.4Ghz, any ideas what to change to increase stabillity?

ASUS P5Q-E Template:

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: 400
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: DDR2-1066MHz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 5
RAS# to RAS# Delay : 15
Row Refresh Cycle Time: AUTO
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: AUTO
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO

CPU Voltage: 1.2250
CPU GTL Voltage Reference (0/2): 0.63
CPU GTL Voltage Reference (1/3): 0.63
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.26
DRAM Voltage: 2.0
NB Voltage: 1.24
NB GTL Reference: AUTO
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.60

Load Line Calibration: AUTO
CPU Spread Spectrum: AUTO
PCIE Spread Spectrum: AUTO
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
CPU Margin: Optimized

Advance CPU Settings
CPU Ratio Setting: 8.5
C1E Suppport: Enabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Enabled
Execute Disable Bit: Enabled

[BababooeyHTJ]

Your GTLs are pretty low for a quad.

[truehighroller]

Not really.

[Leeghoofd]

Hi guys,



ASUS P5Q-E Template:

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: 400
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: DDR2-1066MHz
DRAM Timing Control: Manual

1st Information :

Row Refresh Cycle Time: AUTO --> 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

DRAM Static Read Control: AUTO --> DISABLED
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO

CPU Voltage: 1.2250
CPU GTL Voltage Reference (0/2): 0.63
CPU GTL Voltage Reference (1/3): 0.63
CPU PLL Voltage: 1.56
FSB Termination Voltage: 1.26
DRAM Voltage: 2.0
NB Voltage: 1.24
NB GTL Reference: AUTO
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.60

Load Line Calibration: AUTO
CPU Spread Spectrum: AUTO --> DISABLED
PCIE Spread Spectrum: AUTO --> DISABLED
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
CPU Margin: Optimized --> Try compatible too

First try the above changes plz, if no go, up the Vcore to 1.25 and test again... hope you are on bios 1406. (solved a lot of issues on my P5Q-E)

[gurusan]

What sort of issues did the 1406 bios solve?

[carepolice]

Hi guys,

I've now build my new system, here's the full spec:

Asus P5Q-E
Q9550, Yorkfield Core 2.83Ghz
(2x2GB) Corsair Dominator DDR2 PC2-8500 1066
XFX GTX 260 (216) Black Edition PCI-E Graphics Card
Corsair 620W HX Modular PSU - ATX12V v2.2 APFC
Coolermaster Cosmos RC-1000 Full Tower Case
Western Digital WD6400AAKS 640GB Hard Drive
Zalman CNPS 9700 LED

I've been running the system for just over a week now, and it's running very sweet... My stock 3D Mark06 score is 14302...

Anyway I want to get a nice overclock for 24/7 use, I'm aiming for 3.6GHz...

So far i've managed to get 3.0GHz which increased my 3D Mark06 score to 15210, and 3.2GHz which increased my 3D Mark06 score to 15808 these are both rock solid stable...

On the above 2 settings, I only changed the voltage for CPU to 1.2250v and the DRAM to 2.0v everything else was set to Auto...

After reading I found the board likes to over-volt when the voltages are set to auto, so for my 3.4Ghz I decided to put all the voltages in my self...

I then tried 3.4GHz which increased my 3D Mark06 score to 17048, but this failed Prime95 on work thread 1, running a Torture Test (in-place large FFTs) after 2 hours...

Here's how I set the Bios for 3.4Ghz, any ideas what to change to increase stabillity?

ASUS P5Q-E Template:

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: 400
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: DDR2-1066MHz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 5
RAS# to RAS# Delay : 15
Row Refresh Cycle Time: AUTO -> 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: AUTO -> Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO

CPU Voltage: 1.2250 -> Change it to 1.2500
CPU GTL Voltage Reference (0/2): 0.63
CPU GTL Voltage Reference (1/3): 0.63
CPU PLL Voltage: 1.56 -> 1.52 no mind to run that high on this low OC
FSB Termination Voltage: 1.26 -> try 1.14-1.18 should be enought for this OC
DRAM Voltage: 2.0
NB Voltage: 1.24 -> Do you really feel like to need 0.14 increase for 400fsb?
NB GTL Reference: AUTO -> ok
SBridge Voltage: 1.20 -> ok
PCIE SATA Voltage: 1.60 -> ok

Load Line Calibration: AUTO -> enabled
CPU Spread Spectrum: AUTO -> disabled
PCIE Spread Spectrum: AUTO -> disabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
CPU Margin: Optimized

Advance CPU Settings
CPU Ratio Setting: 8.5
C1E Suppport: Enabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Enabled
Execute Disable Bit: Enabled

Hello there, i got Q9550 here and i used to run whit 3400Mhz on first days when i got this chip, but hell yeah its most easiest overclock that there can be! On my situation after 3.8Ghz i will need to start tweaking more to stay stable but that 3.4Ghz should be really easy to obtain.

check out your template for my changes, few more to Leeghoofd advice

After all i would just try change LLC enabled and test stability

[benbenbingo]

hello
2nd time for me to post writing here, I am new to oc, and got this question which i dont understand, i have a p5q pro, p5q deluxe, and q9550, q9650,
and i mix and match them cpus and memory, what i get the best match is p5q pro and q9650 ( i have tried to test almost everything i can, coz original idea is to put the expansive cpu with expansive mb p5q deluxe, but it just wont go anything stable more then 3.85. cheaper board better result? anyone have any answer?

pc1, q9650, asus p5q pro,@4.23, watercool zalman xt pc2. q9550 asus p5q deluxe@3.82-water.zalman 1.v2 pc3. q9450 asus rampage fomular @3.74 zalman 2
flex II 1150 4g,watercool zalman 1.v2 ocz reaper 1055x8g corsair fan corsair 800 cl4 8g corsair fan
asus 3870x2 asus 8600gt silent asus 8600gt silent
case, mac pro g5, motherboard and everything inside case antech case antech
is not attached. case is too small.....(stupit choose) psu. coolermaster 650w psu antech 1000w
psu, zcool 700w

pc4 e5430 skulltrail 3.19 2x2 zalman 1v2....once burned
8g corair apple
asus 3870x2
coolermaster 1000
pus zimatech 1000w

[Leeghoofd]

What sort of issues did the 1406 bios solve?

On my E board I got +500FSB clocking again, LLC started to work properly... and for both boards ( E and Dlx) it got again same quad OC'ability as 0803 bios (even with CME setting)

[gazmatrix]

Wow lots of advice, thanks guys...

Here's how I'm testing now:

ASUS P5Q-E Template:

JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: 400
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: DDR2-1066MHz
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: AUTO
MEM. OC Charger: AUTO
AI Clock Twister: AUTO
AI Transaction Booster: AUTO

CPU Voltage: 1.2500
CPU GTL Voltage Reference (0/2): 0.63
CPU GTL Voltage Reference (1/3): 0.63
CPU PLL Voltage: 1.52
FSB Termination Voltage: 1.20
DRAM Voltage: 2.0
NB Voltage: 1.20
NB GTL Reference: AUTO
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.60

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : AUTO
NB Clock Skew : AUTO
CPU Margin: Optimized

Advance CPU Settings
CPU Ratio Setting: 8.5
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Enabled
Execute Disable Bit: Enabled

I'm 1 hour in so far running a Torture Test (in-place large FFTs), I'll let you guys know how it goes, and thanks for all the advice...

[gazmatrix]

A little update so far the system is running stable, and I have also disabled "C1E Suppport" I need a program that really tests the stabillity though as Prime95 takes ages... Any ideas?

[Leeghoofd]

Try the Intel Burn test by Agent God, or the LinX, they put loads of stress on the CPU and can be pretty conclusive... do max test and about 20-30 loops (preferably 64bit OS)... so about finished in one hour... OCCT is also over and done in 2 hours...

Yet again I have to say that there's no 100% bulletproof test... running several (not at the same time ofcourse) might be more reassuring

[gazmatrix]

Try the Intel Burn test by Agent God, or the LinX, they put loads of stress on the CPU and can be pretty conclusive... do max test and about 20-30 loops (preferably 64bit OS)... so about finished in one hour... OCCT is also over and done in 2 hours...

Yet again I have to say that there's no 100% bulletproof test... running several (not at the same time ofcourse) might be more reassuring

Thanks, I'll try the Intel Burn Test, do you have a link to the Linx test and I will give that one a go as well...

Cheers Gaz...

[Leeghoofd]

LinX grab here and extract with winrar : LinX

Full thread here : LinX thread

[chouchou]

FYI that 1406 revision of p5q-e bios revised a lot of bugs from previous bios versions... Flashed a buddy's and got his OC to improev atleast 5%. Good luck

[gazmatrix]

LinX grab here and extract with winrar : LinX

Full thread here : LinX thread

Thanks, i'm grabbing it now...

[gazmatrix]

FYI that 1406 revision of p5q-e bios revised a lot of bugs from previous bios versions... Flashed a buddy's and got his OC to improev atleast 5%. Good luck

Yeah I'm running the 1406 and I'ts been a solid Bios for me as well...

[khurios2000]

JumperFree Configuration Settings:

AI Overclock tuner: Manual
CPU Ratio Setting: 9
FSB Strap to North Bridge: Auto
FSB Frequency: 445
PCI-E Frequency: 100
DRAM Frequency: DDR2-1069
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Auto

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: 55
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Enabled
AI Clock Twister: Auto
AI Transaction Booster: Auto
Common Performance Level [10] If I set previous to manual this one is at 5
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED

CPU Voltage: 1.27500
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.52
FSB Termination Voltage: AUTO
DRAM Voltage: 2.1
NB Voltage: 1.30
NB GTL Reference: AUTO
SBridge Voltage: 1.20
PCIE SATA Voltage: 1.50

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
CPU Margin Enhancement: Optimized

Advance CPU Settings
CPU Ratio Setting: 9
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel(R) Virtualization Tech: Disabled
CPU TM Function: Enabled
Execute Disable Bit: Enabled

Got BIOS template from Leeghoofd
30 min OCCT stable
and Intel CPU burn 5X

Bios 1406
2GB Ballistix PC2-6400
E8500 E0

[gazmatrix]

Hi guys,

What would be a safe temp for the Q9550 45nm Yorkfield?

When running LinX on a 20000 problem size for 30 loops the hottest core in Everest hits 73c, is this safe?

The CPU temp is only 55c, I know the Core temps are hotter but 73c does seem quite high, my Zalman is running at 2200rpm so I can increase this if needed...

Oh and I seem to have it rock solid now, with only 1.225v for the CPU...

Thanks for all the help...

[Diablero]

Hi guys,

What would be a safe temp for the Q9550 45nm Yorkfield?

When running LinX on a 20000 problem size for 30 loops the hottest core in Everest hits 73c, is this safe?

The CPU temp is only 55c, I know the Core temps are hotter but 73c does seem quite high, my Zalman is running at 2200rpm so I can increase this if needed...

Oh and I seem to have it rock solid now, with only 1.225v for the CPU...

Thanks for all the help...

.

How is the vcore and cpu clock? it is stock?

for stock, this temp is not problem, but with overclock you may have stabilty issues.